Page 5 of 7 FirstFirst ... 34567 LastLast
Results 41 to 50 of 69

Thread: DIY 94-97 to 98-99 Patch Harness Parts

  1. #41
    Quote Originally Posted by yellowstealth View Post
    99 SL ECU showed up today, so I just stuck it in, pulled the stock ROM and saved it, and flashed the VR4 ROM to it. Since that worked, I'm assuming my OBD2/Flash port connections are correct, so here they are:

    OBD2 Pins 4 & 5 to chassis ground
    OBD2 Pin 16 to 12v switched power
    OBD2 Pin 7 to Pin 85 on ECU
    Flash port Pin 26 to Pin 100 on ECU

    I'll post a final spreadsheet when I'm sure of the rest of my connections.
    This great news, I aslo have a 99SL ECU. Did you push a 99VR4 Rom? I haven't started this project since my won't start since November .

  2. #42
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2002

    Location
    Monterey Bay, CA
    Posts
    31
    Thanks
    2
    Thanked 0 Times in 0 Posts
    I did load the 99 vr4 rom. I'm having an issue with evoscan freezing when I try and log in 3000gt/dsm mode. OBD2 will connect, but obviously I want to use the 3000gt mode so I get all the correct sensors and can log knock. I haven't done much other than start the car. It starts right up, idles ok, I backed it out into driveway and pulled back into the garage, but I don't feel comfortable doing anything more until I've got the logger working properly and have verified everything's working as I expect it to.. It's wanting to idle real lean, but I suspect that's just because I don't have my values for the PTE 550 injectors right. I found latency settings for just about every other injector, but not the 550s.

  3. #43
    Pin 1 on the OBD2 plug needs to go to pin 84 diagnostic ground pin. This puts the ECU into MUT mode when ground is present.

    p.s. I'm also running a 99 3000GT VR4 ECU into my 93 car, loving it so far.

  4. #44
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2002

    Location
    Monterey Bay, CA
    Posts
    31
    Thanks
    2
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by BlackStealth View Post
    Pin 1 on the OBD2 plug needs to go to pin 84 diagnostic ground pin. This puts the ECU into MUT mode when ground is present.

    p.s. I'm also running a 99 3000GT VR4 ECU into my 93 car, loving it so far.
    Thanks, I got that one already but hadn't updated. I'm curious did you build your own adapter or purchase one? Also, are you able to log using the 3000gt/dsm mode in evoscan, or are you using MUT-III?

  5. #45
    I can use both modes. One mode is MUT mode, the other mode is OBD2 which encapsulates MUT requests at a slow rate.

    My cable is a boomslang harness which I verified and corrected. Someone was selling the 99 3000GT VR4 ECU, Boomslang conversion harness and OpenPort 2.0 cable so I purchased it all.

  6. #46
    Keeping it real...
    Join Date
    Sep 2010
    Owner Since
    Oct. 2006

    Location
    Reno, NV
    Posts
    448
    Thanks
    20
    Thanked 21 Times in 19 Posts
    Great thread thus far. Been thinking about doing my own harness.

  7. #47
    subscribed.

  8. #48
    www.chromedecu.org verified

    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    DFW
    Posts
    565
    Thanks
    53
    Thanked 53 Times in 36 Posts
    subscribed...
    www.Chromedecu.org
    Plug and Play Flash Ecus, why use a harness when you can just Plug and Play?!
    2 year Warranty on all ECUs.
    A donation of every Plug and Play Flash Ecu sale goes to Greg for more software goodness.
    1999 Flashed Wide body 3000GT VR4, (Its Cianci's prototype car, but don't worry I fixed that.)
    How To Contact Me:
    eMail: apape10@yahoo.com
    3SI: Jesters Deadd
    www.Chromedecu.org

  9. #49
    Forum User verified
    Join Date
    Oct 2010
    Owner Since
    1993

    Location
    St Louis
    Posts
    343
    Thanks
    29
    Thanked 48 Times in 31 Posts
    I have the harnesses for 1g, hybrid, and 2g available through morgon's motorsports (xwire), all come with a reflash plug and the 1g comes with an obdII port.

    You can source all of the parts and DIY - but if you look at the prices of the hard parts and factor in S&H of the hard parts, then factor in your time, your loss of hair, etc, etc, your not saving your self any money and you are def costing yourself TIME. Now I have been fabbing these up for some time now. I make 10 to 20 at a time. I have had to teach my poor gf how to solder and junk because it is just such a PITA.

    So, for the unconvinced:

    Lets look JUST at the 99 ecu plugs:
    28 Pin Plug 1 @ $2.50 ea add 17.00% for average S&H from DigiKey $2.93
    28 Pin Plug Pin Retainer 1 @ $0.75 ea add 17.00% for average S&H from DigiKey $0.88
    30 Pin Plug 1 @ $5.16 ea add 17.00% for average S&H from DigiKey $6.04
    30 Pin Plug Pin Retainer 1 @ $0.75 ea add 17.00% for average S&H from DigiKey $0.88
    35 Pin Plug 1 @ $2.73 ea add 17.00% for average S&H from DigiKey $3.19
    35 Pin Plug Pin Retainer 1 @ $1.18 ea add 17.00% for average S&H from DigiKey $1.38
    Sig (Small) Pin 75 @ $0.38 ea add 17.00% for average S&H from DigiKey $33.35
    Pwr (Large) Pin 18 @ $1.04 ea add 17.00% for average S&H from DigiKey $21.90

    TOTAL $70.55 - Thats just for the 99 ECU side
    Figure about $10 to $13 bucks for the 1G or 2G ecu connector.
    Oh - and if you have a 1G, you need an OBDII Port. And dont forget the mitsu reflash plug.

    So figure at LEAST $100 in parts. No Wait, add solder, heatshrink, and wire. You shouldn't just slap any old wire into those 99 ecu connectors. The pin crimp specification is 1.4mm wide on the signal pin. Soooo if you crimp 1.7mm wide because you are not using ultra thin wall (TXL) wire, you will have to work real real hard in stuffing all those pins in the connector. But I suppose if you want what they pass of as primary wire at your local auto parts store, then by all means have at it.

    Now you got your conversion table - what pin goes to what pin. Don't make a mistake or you might be buying a new ecu. You get everything fabbed up and how much time did you spend? I bet at least an hour or two. Do you figure your lost time with your family and friends is only worth $2.50 hr? Any way you slice it, it is so much nicer to just order the part, slap it in, and walk away . . . that being said . . .

    Von can yell at me later - I have the 1G / hybrid / 2G connectors available through Morgan's Motorsports (xwire). Everything is built with extra thin wall TXL cross-linked polyethylene wire rated at 60v and between -59°F to 275°F. Resistant to moisture, grease, oil, gasoline, and most solvents. It meets or exceeds SAE J1128. Check with xwire for pricing.

  10. The Following User Says Thank You to 99 vr4 For This Useful Post:


  11. #50
    Keeping it real...
    Join Date
    Sep 2010
    Owner Since
    Oct. 2006

    Location
    Reno, NV
    Posts
    448
    Thanks
    20
    Thanked 21 Times in 19 Posts
    What is your price then?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering