Page 452 of 892 FirstFirst ... 352402442450451452453454462502552 ... LastLast
Results 4,511 to 4,520 of 8916

Thread: What did you do today to your 3/S?

  1. #4511
    Forum User
    Join Date
    Sep 2010
    Owner Since
    2002

    Posts
    1,668
    Thanks
    514
    Thanked 388 Times in 259 Posts
    Quote Originally Posted by CoopKill View Post
    I was hell bent on the TSW nurburgring as well, but Nathan's AMR's are half the price at a 3lb gain so This is where I am going...
    Ordered one in grey for test fitment. I really wish they sold them in bronze, but I guess that's a future project if they fit.
    '93 VR4 | 10.57 @ 135 on C16 | 11.29 @ 125 on 93 | ~3275 lbs

  2. #4512
    Forum User Not Verified
    Join Date
    Jan 2011
    Owner Since
    2010

    Location
    az
    Posts
    1,081
    Thanks
    10
    Thanked 3 Times in 3 Posts
    Quote Originally Posted by anyonebutme View Post
    smushed center mains FTL.

    Damn how did that happen !!??
    Ross 9:1 piston, H beam rods with arp bolts, *Forged crank,*Ported head with brian crower 1mm over intake and exhaust valves,*Brian crower valve springs,Oem headgaskets,*Arp headstuds*,T3 hybrid turbos with .63ar,*Tial leaded fuel wastegates with 1bar springs,*Cx racing fmic*,Arc2 in blowthru,*950cc delphis on e85,Jackhammer fuel hanger holding 2 walbros 255 hotwired ,Fuel lab fpr,*Aeromotive fuel filter*Entire fuel system done in ptfe braided black lines,*Beefed up oil cooler,*Gates racing belt*,Ninja performance soild tension setup*,3sx single pass radiator*,Tial q blowoff*,Scanmaster*,Aem twin fire*,3sx fuel rails* battery relocated to trunk, blitz dsbc, aem wideband, autometer oil pressure gauge,And so on....

  3. #4513
    The one. The only. verified
    Join Date
    Sep 2010
    Owner Since
    August 28, 2002

    Location
    SWPA
    Posts
    4,042
    Thanks
    182
    Thanked 699 Times in 529 Posts
    I fired it up. Was going to take it for a ride, but have a flat rear tire. Aired it up, but it went right back down. There is a spot on the rear lip (bead) that is bent.

    [06-05, 19:29] OhioSpyderman: Brian, finding a woman is NOT the answer, you need to shop for a good VACUUM

  4. #4514
    SKADOOSH!!! verified
    Join Date
    Sep 2010
    Owner Since
    2008

    Location
    Prince George
    Posts
    1,295
    Blog Entries
    4
    Thanks
    46
    Thanked 49 Times in 42 Posts
    cleaned it all up, put most of my interior back in, and phoned around to figure out what the hell is going on with my turbo plumbing. I was hoping it'd be here by now... If not for that I could theoretically fire my car up for the first time since the build... after it's all welded up and installed of course.
    Photobucket

  5. #4515
    DR-750 club Not Verified
    Join Date
    Sep 2010
    Owner Since
    I could drive.

    Location
    Portland, Texas
    Posts
    2,546
    Thanks
    96
    Thanked 172 Times in 124 Posts
    I painted my block. Looks way better now.
    July 2014 COTM
    We follow the earth. The earth follows the stars. The stars know their way and though the body dies. The stars will remain, like the waves of the sea and restless slate.

  6. #4516
    Moved it. Under its own power. :] <3

  7. #4517
    Forum User
    Join Date
    Sep 2010
    Owner Since
    2002

    Posts
    1,668
    Thanks
    514
    Thanked 388 Times in 259 Posts
    Can you use stock valve springs on crower 272's spinning up to ~8050 rpm's?

  8. #4518
    Member Not Verified
    Join Date
    Nov 2010
    Owner Since
    2003

    Posts
    2,062
    Thanks
    112
    Thanked 272 Times in 206 Posts
    Quote Originally Posted by keo92stealth View Post
    Damn how did that happen !!??
    Me and Von have differing opinions on the cause. He believes the center mains were too tight when the previous owner "rebuilt" it. I'm going with crank whip. We'll soon know if it self destructs again soon.

  9. #4519
    DR-750 club Not Verified
    Join Date
    Sep 2010
    Owner Since
    I could drive.

    Location
    Portland, Texas
    Posts
    2,546
    Thanks
    96
    Thanked 172 Times in 124 Posts
    I am pretty sure you can.

  10. #4520
    Forum User Not Verified
    Join Date
    Jan 2011
    Owner Since
    2010

    Location
    az
    Posts
    1,081
    Thanks
    10
    Thanked 3 Times in 3 Posts
    Quote Originally Posted by AdamVR4 View Post
    Can you use stock valve springs on crower 272's spinning up to ~8050 rpm's?
    I dont think springs are required for 272s. But your spinning her pretty high there adam . Sure u would feel safer with springs?

Page 452 of 892 FirstFirst ... 352402442450451452453454462502552 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering