Page 5 of 40 FirstFirst ... 3456715 ... LastLast
Results 41 to 50 of 391

Thread: Big Single Build

  1. #41
    I don't own a VR4! Not Verified
    Join Date
    Sep 2010
    Owner Since
    2007

    Location
    Andover, MN
    Posts
    529
    Blog Entries
    1
    Thanks
    3
    Thanked 19 Times in 17 Posts
    OK ladies and gentlemen, I want to put a status update out there because there will be quite a bit of insanity going on with the car.

    Keep in mind with all of the work going in to this project it really is not all in vain. While I really want to be unique and attempt to get a single turbo setup bolted on a SOHC engine and go fast, it really is not about that. I want to build something that is challenging. After all, I really don't have a ton of money tied up in this car, and the existing engine in the car still runs fine. There are many reasons why I didn't pull the engine out of the car and rebuild it, but I won't list them here. Thanks to Josh Mitoska for pulling this engine last minute before the NG and for giving me a killer deal on the entire engine.

    So here's what I am after with this car. I have always liked what NRE does with their engines in terms of the harnesses they build. They build single connector harnesses, so, one of the things that I do plan on doing is to build a single connector engine harness that disconnects near the firewall. One of the reasons I want to do this is to clean up some of the wiring that gets routed every which way across the engine. Also I really dislike having to disconnect all of the plugs off of the main harness just to yank the engine out; it would be much simpler to unplug one plug and yank the engine out with all of the components still plugged in.

    I also never liked the idea of the main fuse box under the hood of the car. I mean I get why it's done, but I would much rather have it relocated inside the car. So that will be taking place as well, this will be a major undertaking as the main fuse box wiring is kinda a cluster.

    Also, since I am really turning this into because racecar status, the interior panels will be coming out. The door locks and power window switches will be relocated to new switch panels in a modified center console and the center console will also be fitted with switches for manual override to any components that are powered by a relay. My thought is to retain existing relays, however install switches that allow me to manually override the relay in the event a relay goes bad or other issues exhibit their ugly head. The interior lighting will go away, the unnecessary electronics will go away, ABS will be deleted, A/C will be deleted, all of the carpc stuff that I originally planned for the car will be put in a different vehicle.

    So what are the plans for the engine?
    Last edited by Boost4VR4; 08-14-2013 at 01:19 AM.
    Your 1993 Dodge Stealth is one of 6351 that received VIN numbers. Based on the order of the serial numbers, your car was the 5212nd out of the 6351 that were made that year.
    Your car was built in the 3rd week of February 1993. Of the 47380 vehicles made at the Nayoga plant, your car was the 40537th vehicle to be created that year.
    There are 281 other cars that were made with both the same interior and exterior color. There are 779 cars with the same exterior color and 2316 cars with the same interior color.
    Note: The production order is assigned based on the order of the serial number.

  2. #42
    Member verified
    Join Date
    Sep 2010
    Owner Since
    Oct '08 - Oct '10

    Location
    Royersford, PA
    Posts
    3,814
    Blog Entries
    1
    Thanks
    1,059
    Thanked 442 Times in 317 Posts
    Where does the CarPC end up?
    R135
    ╚╬╬╝
    - 24

  3. #43
    I don't own a VR4! Not Verified
    Join Date
    Sep 2010
    Owner Since
    2007

    Location
    Andover, MN
    Posts
    529
    Blog Entries
    1
    Thanks
    3
    Thanked 19 Times in 17 Posts
    Quote Originally Posted by DocWalt View Post
    Where does the CarPC end up?
    I am not sure yet. I know for certain that the amplifier that I was going to use for the audio setup will be going in my mom's Jaguar. She wants to upgrade the sound and out of the factory they put the battery in the trunk, so it should be an easy hookup.

  4. #44
    I don't own a VR4! Not Verified
    Join Date
    Sep 2010
    Owner Since
    2007

    Location
    Andover, MN
    Posts
    529
    Blog Entries
    1
    Thanks
    3
    Thanked 19 Times in 17 Posts
    Alright, a lot of things have happened this week, but i did find time to work on the engine. So I started more teardown, I got the torque convertor off of the flexplate and took the flexplate off. Got the engine on the stand and started cleaning up the parts and organized parts. Tomorrow I need to go through and throw some bolts in bags and such. So I cleaned parts and then I started to work on the bottom end. So I took the oil filter housing off, took the oil dipstick tube out, rotated the block and drained the coolant. Unbolted the oil pan off voila:

    Talk about SLUGDGE! The engine did sit for awhile, but I also think before the head gasket blew that this engine had poor oil change routines and the pickup tube is full of sludge. So basic design, 2 bolt mains. Took the girdle off and took a photo of each of the bearings:




    Here are some shots of the main crankshaft journals:




    I loosened the connecting rod bolts and will be pulling the pistons out and sending the block out to a shop to be built.

  5. #45
    I don't own a VR4! Not Verified
    Join Date
    Sep 2010
    Owner Since
    2007

    Location
    Andover, MN
    Posts
    529
    Blog Entries
    1
    Thanks
    3
    Thanked 19 Times in 17 Posts
    So I got a bit accomplished today. Pulled the pistons out, pulled the crankshaft out. Super clean bottom end other than the sludge at first.
    Here are the results:















  6. #46
    Member verified
    Join Date
    Sep 2010
    Owner Since
    Oct '08 - Oct '10

    Location
    Royersford, PA
    Posts
    3,814
    Blog Entries
    1
    Thanks
    1,059
    Thanked 442 Times in 317 Posts
    The bearings all look pretty good, but man, talk about sludge!

  7. #47
    Wrench Monkey Not Verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Rochester, NY
    Posts
    712
    Thanks
    41
    Thanked 26 Times in 19 Posts
    Looks like a Saab I once owned, they're known for poor oil change maintenance causing exactly that. Sludge.
    1997 3000GT VR4 - Solano Black Pearl - E85 - E316G-BIG - All the boost
    1993 3000GT VR4 - Maroon/Blacktop - Back to stock/Restoration
    1994 Stealth R/T - Primer - Parts store

  8. #48
    BAD ASS - I've got one Not Verified
    Join Date
    Sep 2010
    Owner Since
    2/2010

    Location
    L'Anse, MI
    Posts
    2,476
    Thanks
    1,262
    Thanked 594 Times in 488 Posts
    I'm always amazed to see decent bearings on a sludge-pump.

    Looking good, Kev.
    Ranked No. #1 in initial quality

    Idiots, simply by being idiots, seem capable of achieving randomly bad things that are beyond the imaginings of sensible people.

  9. #49
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    nice, if that was a TT with that sludge there would be rods through the block.

    Parting 6 speed
    Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace

  10. #50
    The one. The only. verified
    Join Date
    Sep 2010
    Owner Since
    August 28, 2002

    Location
    SWPA
    Posts
    4,042
    Thanks
    182
    Thanked 699 Times in 529 Posts
    SOHC's definitely can take a beating.

    [06-05, 19:29] OhioSpyderman: Brian, finding a woman is NOT the answer, you need to shop for a good VACUUM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering