Page 4 of 55 FirstFirst ... 234561454 ... LastLast
Results 31 to 40 of 544

Thread: Tuning my DR750s on Chrome

  1. #31
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    I'm curious, I read in a different thread you didn't use the main bearings you bought when you swapped the rod bearings. Did you pull the girdle and check them, or make an assumption based on the good condition of the rod bearings?


    Real Performance Automotive (541)816-4500 www.FB.com/RealPerformanceAuto

  2. #32
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Quote Originally Posted by RealMcCoy View Post
    I'm curious, I read in a different thread you didn't use the main bearings you bought when you swapped the rod bearings. Did you pull the girdle and check them, or make an assumption based on the good condition of the rod bearings?
    the latter, so yeah the mains could've been bad

    Parting 6 speed
    Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace

  3. #33
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    Damn that sucks. I hope the turbo repair isn't too expensive. I would doubt that the turbine shaft got damaged but I seemed to guess wrong on the turbos every single time because it ends up being much more expensive dealing with vendors. If you had a 6G74 block and crank I'd say do a 3.5-3.8L Pampena motor for $3750 but it's a little expensive sourcing a JDM engine. Your best bet may be to buy some Ninja Performance rods, send your motor to Ray, and have him put it together with his custom Ross pistons and race wrist pins. That's probably what I would do.

    Also, I don't know if it's something you want to consider at all for motor safety next time but you could pick up BlackStealth's LCD BC. I love it and it has been a huge lifesaver for me monitoring knock real time in my face with it sitting in the tach gauge. There's plenty of times I would have done a pull and not known I had knock starting at part throttle if I didn't have it there. I know with a flashed ecu you won't have any tune drifting but there's still limited fail safes for knock compared to standalones that can monitor fuel and oil pressures. I would consider the LCD BC next time. $250 is cheap insurance. I also don't think I would trust the oil cooler. It's a risky chance. I've cleaned them out before very thoroughly and not had issues but maybe I got lucky.
    95 RT/TT Billet TD04s E70, DW1000cc injectors, ARC-2 with 92mm maf, 3SX fuel rail loop, hotwired Walbro 416/485, 3" FMIC, single small Krank vent, DR 3.5" downpipe and cat-back, DNP 02 housings, Hallman Pro MBC, BlackStealth LCDBC, AEM wideband, AEM oil pressure, Apexi S1 coilovers with SCE EVO 8/9 adapters, 3SX adjustable control arms, Spec 3+ clutch, Maximal solids/3SX poly motor mounts, Setrab custom SMOC, stock motor 127k miles, stock drivetrain.

  4. #34
    Banned J. Fast's Avatar
    Join Date
    Sep 2010
    Owner Since
    - O - SIX -

    Location
    Colorado, USA
    Posts
    2,711
    Thanks
    405
    Thanked 200 Times in 140 Posts
    WOW! Didn't you just line service that engine?

  5. #35
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    I'm not sure what you mean, but I did replace the rod bearings, the oil pickup, and pan as a precaution. The old bearings had virtually no wear.

  6. #36
    Forum User
    Join Date
    Sep 2010
    Owner Since

    Posts
    503
    Thanks
    11
    Thanked 84 Times in 75 Posts
    Bearing wear on these engines starts with the 2 center mains. After the clearance on the mains gets opened up, you lose pressure to rods 2,3,4,5.

  7. #37
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Well I pulled the front 3 plugs. There is a chalky substance on the ground straps that wipes off easily. Not sure if that would be a lean indicator or burning some oil. I kept an eye on oil consumption and didn't notice any. I can see a gray/black ring down in the porcelain base about a mm off the bottom of the porcelin. There is about one thread worth of black on the plug body.

    I can not positively identify a timing line on the ground strap, when I pull the three rears I will check again. I think I see some faint color just before the bend.

    There is no ground strap erosion, electrode damage, or any specks on the plug at all. Besides the white chalky crap on the ground strap I'd say they look great. I think they may be a bit hot based on the whiteness of the groundstrap, I'll switch to 8 series next time.

  8. #38
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Let's entertain that the engine was running lean for some reason. Wouldn't it have broken one of my fragile 2G ringlands before pounding out the rod bearings?

    Oh I also pulled the intake off the front turbo and it spins freely with no play. I'm still going to send them to DR for inspection or rebuild if they need it.

  9. #39
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Quote Originally Posted by donniekak View Post
    Bearing wear on these engines starts with the 2 center mains. After the clearance on the mains gets opened up, you lose pressure to rods 2,3,4,5.
    Donnie, I appreciate the input, but I've seen enough worn center mains to be aware of that. Usually #6 rod gets worn by the time the centers are worn badly. Like I said all of the rod bearings were perfect when I pulled them. I'll pull the main girdle when I get this thing apart and we can see.

    I'm sure you are worried about localized low oil pressure, but it was decent enough on the gauge. About 20 PSI per thousand rpm with 20 PSI at 850-900 RPM on mobile 1 10w40.

    I kept an eye on the oil pressure yesterday like a hawk and it didn't go down until today when it started knocking it got down to about 10 PSI at idle.

  10. #40
    I AM IMPORT POWER
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Driving Vicki Crazy
    Posts
    1,105
    Thanks
    56
    Thanked 270 Times in 125 Posts
    Well this sux.

    -Chris

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering