Page 1 of 5 123 ... LastLast
Results 1 to 10 of 44

Thread: Not Running Right After Evo Injector Install

  1. #1
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts

    Not Running Right After Evo Injector Install

    Well I finally got around to installing my Evo 560s today. Everything was going smoothly for once until I fired it up after the install.

    Sounded like a truck at first with 600CC (what the injectors actually flowed) and latencies off the EvoM board. Then tried the latencies from this board and it got a little better. Then put 560CC and got a little better but still doesn't sound right. Wideband says it is running ~16:1 at idle. If I rev it it sputters as the revs rise but if I hold the RPMs steady is sounds about the same as idle. When I let off it will read 12:1 for a second.

    Trims are ~120 low and mid (can't remember exactly) and 100 high. They were about 120/110/100 before the install (didn't reset the computer). The O2 trim fluctuates from 100 to 120.

    CEL came on after a while but when I tried to read it is says speed sensor.. I am not real familiar with Evoscan though so maybe I picked the wrong setting? Evoscan 2.9 and Chrome V2.

    When I disabled injectors they all made an impact (which varied from injector to injector) except #4. Please tell me this is the middle one on the rear bank lol

    I don't see any leaks on the front bank and don't smell any fuel. New O-rings and insulators. Put the retaining clips back in the plugs as well as the metal thing that holds them on the rail.

    Fuel pressure is good.

    Only things I can think of are:
    1. Messed up flash ECU settings (all I changed was injector size and latencies).
    2. Messed up wiring - the wires sound pretty crispy when I was doing the install. I tried wiggling what I could reach and it didn't change anything though.
    3. Forgot to plug something back in/put something back on - I followed the stealth316 tutorial if you are wondering what I removed.
    4. Vacuum leak - I did use a new plenum gasket though.

    What should I do? Any ideas?

    Should I put the stock ones back in (rule out electrical), rearrange the Evo injectors (isolate the problem to one injector), remove plenum and cut back the sheath on the wiring to inspect it/run continuity test, something else? I don't have a compressor here or I would pressure test. Any other ideas? I am busy with school (this past weekend I had some time off) so whatever is the most time efficient is the ticket for me.

    Thank you!
    Last edited by HLxDrummer; 05-05-2013 at 09:17 PM.

  2. #2
    Keeping it real...
    Join Date
    Sep 2010
    Owner Since
    Oct. 2006

    Location
    Reno, NV
    Posts
    448
    Thanks
    20
    Thanked 21 Times in 19 Posts
    What numbers did you use for your injectors?

  3. #3
    Forum User
    Join Date
    Apr 2013
    Owner Since
    2010,HAD 3GTO SINCE 2000 ONE NA AUTO ONE NA MANUAL NOW BEST OF ALL TT MR

    Location
    UK
    Posts
    35
    Thanks
    0
    Thanked 0 Times in 0 Posts
    hi ,mate ,not alot of poeople use the 560 evo injectors over here in uk on gto,s they always seem to have issues < almost imposible to set up on our cars> if you contact rob at evil empire uk he maybe able to tell you more.there is not nothing he dont know about these cars simon
    Last edited by GTO-SIMON; 05-06-2013 at 06:09 AM.

  4. #4
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    I tried these values:

    4.7V/3.312mSec 7.0V/1.680mSec 9.4V/1.032mSec 11.7V/0.672mSec 14.0V/0.432mSec 16.4V/0.264mSec 18.6V/0.144mSec

    and these:

    16V - 0.628
    14V - 0.748
    12V - 0.928
    10V - 1.208
    8V - 1.688
    6V - 1.900

  5. #5
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Evoscan 2.9 can't read/clear CELs. It is broken.

    2014 Exomotive Exocet - #101 "shocker yellow" - 1.8L 5-speed 3.9 torsen FMII powered
    Read more: http://mevowners.proboards.com/threa.../greg-pa-build

    99 Solano Black VR4 - #16 of 287 - ground up restoration - sold
    98 Pearl White VR4 #54 of 231 - 12.84@105mph - 93 Octane 12.50@107mph - 100 Octane with Chromed ECU - sold
    99 Pearl White VR4 #108 of 287 - 3RD place stock car class ECG 11 - Sold
    98 Black VR4: 100% stock - totalled by an Illegal 2-12-08
    95 White Stealth TT - 11.852 @ 118.25 - sold
    95 SSG Stealth TT - 11.981 @ 115.81mph - sold

    "I don't actually work on cars, I just talk about them on the internet."

  6. #6
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Quote Originally Posted by GTO-SIMON View Post
    hi ,mate ,not alot of poeople use the 560 evo injectors over here in uk on gto,s they always seem to have issues < almost imposible to set up on our cars> if you contact rob at evil empire uk he maybe able to tell you more.there is not nothing he dont know about these cars simon
    Huh???

  7. #7
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    Hm.. any other way I can read them? I don't remember if I can with my LCDBC or not.

  8. #8
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Quote Originally Posted by HLxDrummer View Post
    I tried these values:

    4.7V/3.312mSec 7.0V/1.680mSec 9.4V/1.032mSec 11.7V/0.672mSec 14.0V/0.432mSec 16.4V/0.264mSec 18.6V/0.144mSec

    and these:

    16V - 0.628
    14V - 0.748
    12V - 0.928
    10V - 1.208
    8V - 1.688
    6V - 1.900
    The first string of numbers is what I always used with the 560s. I did use 535 for the scaling, but every car is different.

    read the cel with evoscan 2.6, if you email hamish he will get you a license for the older version. See my thread about deleting the ftdxxxx dll in the evoscan 2.6 folder.

  9. #9
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Quote Originally Posted by Greg E View Post
    Huh???
    I believe what Simon is referring to is the problems people run into using the 560s with the stock ecu. It is extremely difficult to get the car to idle stoic.

    They work perfect when setup on the flash ecu.

  10. #10
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    Quote Originally Posted by Forest Gump View Post
    The first string of numbers is what I always used with the 560s. I did use 535 for the scaling, but every car is different.

    read the cel with evoscan 2.6, if you email hamish he will get you a license for the older version. See my thread about deleting the ftdxxxx dll in the evoscan 2.6 folder.

    Ya the first set is what I am using now and which made it run better than the second set.

    I will try to get 2.6 installed again (that is what I was running with V1) and see what that says. I tried pulling the code with my LCDBC but it isn't working right..

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
  • History
  • Information
  • Groups
  • Events
  • Resources
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net