Page 5 of 6 FirstFirst ... 3456 LastLast
Results 41 to 50 of 54

Thread: Custom Arduino keyless entry + auto window/trunk integration...

  1. #41
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Came up with some design flow for the fob/receiver to include passive entry. We'll see how well this works out, the biggest hurdle will be battery life on the fob.

    Last edited by Toni; 11-05-2011 at 02:55 PM.

  2. #42
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    So I got the fob button code working. It now correctly debounces and handles single and double clicks on all 5 buttons only sending one byte for a command. Both the uC and transceiver go into power down modes when there is no button press. It should be in the nA range. My meter reads 0mA I can still go one more power mode lower on the transceiver but then I have to reinitialize it and use another pin. Not sure if it's worth it.

    I ran out of program space to implement the passive entry but I won't be using a tiny2313 that I'm testing on now, most likely attiny44 or 84. The toughest part will be fitting the transceiver board and tiny on the fob board.

  3. #43
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    So I worked on the board this weekend. Had to redesign the above board somewhat. I forgot to add an antenna trace (yea that might help range out a bit), pins to program the chip, can't do it on a bread board since it's surface mount, and the data pins into the transmitter were switched DOH!

    After I milled out the first side I realized I put the antenna underneath the battery Luckily I was still able to put it on the other side. Part of the board didn't mill all the way because the copper layer was lower in that section. This is a main problem with fine cnc milling of pcbs since I use a v bit for the best cut. I manually moved to these sections and cut them deeper but I forgot to lift the cutter up at the end and moved it across two traces, DOH!

    Nothing major so far, I keep going... Hardest thing to solder is the QFN 20...


    Yea, tiny bitch is tiny. The pads for it are .3mm and the space between them is .2mm. Unfortunately, since I use a .2mm v bit, by the time I get it deep enough and any spindle wobble, it's about .3mm. So I extend the gap between the pads to .3mm leaving only .2 for the pad. I ended up cleaning the board after cutting it and two of the pads came off Stupid things are fragile. So I decide to keep going and use wire strands as jumpers. I end up getting it soldered on, programmed, and tested outside of the case. Woohoo!

    So I fit it into the case and give it a go. Stupid thing won't work. Turns out I managed to break some of the connections(fragile) and can't continue. Gonna try another board tonight. Maybe I can make the pads larger and soldered better. This won't be a problem with a real board but I would have wasted money had I sent the first design in.

  4. #44
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    When you send out for boards where do you go? I have a couple of sources I've used that are relatively cheap and great quality.

  5. #45
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Quote Originally Posted by Jimvr4 View Post
    When you send out for boards where do you go? I have a couple of sources I've used that are relatively cheap and great quality.
    I actually haven't had any professionally made yet. Everything up to this point has been soic and larger and my CNC has no problems making it. QFN, etc is a much different animal so I will need one made if I want this thing to last. I was looking at dorkbot (PCB Order | DorkbotPDX) $5 a square inch for three boards shipped no setup fee. Curious, where you have gone? Feel free to pm if you want to keep it private.

    Thanks
    Antoni

  6. #46
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    Sending you a PM

  7. #47
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    All done! Prototype board seems to work pretty well.










  8. #48
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    I was bored and decided to play around with manual mode on the camera...






  9. #49
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Well, in case anyone was wondering where this thread went. I ended up using this as a project for school. Now that I am done I can update my progress.

    Here is a shot of the board made on my cnc.



    Here is an in car test of the unit working in the car.


  10. #50
    I'm Marcus
    Join Date
    Sep 2010
    Owner Since
    '98

    Location
    Denver Colorado
    Posts
    98
    Thanks
    14
    Thanked 49 Times in 28 Posts
    Pretty cool and nice work. I'm super impressed you fabbed your own PCB boards by CNCing them. Some serious tech.

    Duke

    Favorite Car - A 1998 RED VR4 , pretty much stock except: Suspension: '94 ECS Struts Retrofit w/ Tein H-Techs controlled by TechWorks ECS Suspension Controller

    www.renegadetechworks.com Open Source 3000gt ECS Retrofit & Replacement Controllers

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering