Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: I Fail...

  1. #1
    Secret Lurker Man! verified
    Join Date
    Sep 2010
    Owner Since
    7/10/06 or somethin

    Location
    Bend, Oregon
    Posts
    452
    Thanks
    13
    Thanked 20 Times in 14 Posts

    I Fail...

    So, I've finished my 3rd attempt at eliminating leaks and to no avail...did the 120k service, first attempt, cleaned and prepped both surfaces with 600 or 400 (can't remember) wet-n-dry, used gasgasinch on gaskets, torqued everything to spec, let sit over night before adding fluids and starting, had a small leak after a month, so tore it all back down, used fel-pro gaskets, cleaned and prepped the same, this time, installed gaskets dry (no sealants of any type) torqued by feel, sat over night before adding fluids and starting, ended up using an old Right stuff on the oil pan, that didn't dry so it leaked like a sieve, tore it down to find the other gaskets were leaking some as well.....

    THIRD TIME'S A CHARM...fel-pro gaskets again, this time used Roloc green discs on everything, nicely/evenly scuffed up, used permatex copper spray on gaskets, over torqued everything by 2 ft/lbs, let sit over night before adding fluids and starting...after two months, leaks again...

    What the hell am I doing wrong here? Only thing I can think of is, after full assembly, run engine to operating temp. let fully cool, then go through and re-torque everything??

    I can't stand leaks and there's no excuse or reason to have any, not even the smallest of leaks, I've tried with and without any sealants, torqued to spec, torqued by feel, over torqued...I dunno, I'm baffled, I've never had this much trouble with anything, I dunno what I'm doin wrong here, I feel retarded...*sigh*

    What's your process? Also torque wrench is -/+3% like most so I wouldn't think I was using inferior tools and Fel-Pro is good stuff from what experience I've always had before...

  2. #2
    Forum User
    Join Date
    Jan 2011
    Owner Since

    Posts
    203
    Thanks
    3
    Thanked 31 Times in 22 Posts
    for those of us who havnt been following your posts, what exactly are you fixing "leaks" on? Headgaskets? Water pump? Oil pump? Sump? And what fluid is leaking?
    Last edited by box; 10-04-2011 at 04:38 AM.

  3. #3
    Padawan garage troll Not Verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Newark, DE
    Posts
    635
    Blog Entries
    5
    Thanks
    68
    Thanked 23 Times in 21 Posts
    Don't use the prefabbed gaskets that they sell for oil pan! Only use the FIPG FTW.
    91 AWD TT
    K&N FIPK, Precats gutted, Test Pipe, Blitz DSBC, Walbro 255, Vacuum reduction, SM3, MMCd, Krank Vents, 3SX Aluminum Crank Pulley, Aluminum 2PC DS, MAFT Pro (AFC mode atm).

    To do list: Need to check electronic timing, install FP hotwire, install PS poly MM, RUACAs, Setrab oil cooler, Dejon Y-pipe, 3.5 GM Mas, FIC 650ccs & 13Ts.

  4. #4
    Forum User
    Join Date
    Sep 2010
    Owner Since
    2002

    Posts
    1,668
    Thanks
    514
    Thanked 388 Times in 259 Posts
    I've never experienced "old" right stuff, but it's certainly possible that it can get old and no longer cure.

    Why are you messing around with Felpro gaskets?

    Go buy a new tube of the right stuff for $15 and seal this shit up. I've done ~15, 120K's and NEVER had a leak afterwards. I use NOTHING but OEM gaskets and The Right Stuff. Get both surfaces clean and dry and use liberal amounts of TRS on the oil pan flange. I put a fat bead on the flange then spread it over the whole surface with my finger (wear latex gloves). Once I've got a nice layer over the entire surface, I add TRS to the trouble areas (the bends). You need to be very careful during installation not to drag the mating surface across the girdle. Do some dry runs BEFORE putting TRS on the oil pan.

    There's absolutely no need to "retorque" anything after warm-up.
    '93 VR4 | 10.57 @ 135 on C16 | 11.29 @ 125 on 93 | ~3275 lbs

  5. #5
    Secret Lurker Man! verified
    Join Date
    Sep 2010
    Owner Since
    7/10/06 or somethin

    Location
    Bend, Oregon
    Posts
    452
    Thanks
    13
    Thanked 20 Times in 14 Posts
    Quote Originally Posted by box View Post
    for those of us who havnt been following your posts, what exactly are you fixing "leaks" on? Headgaskets? Water pump? Oil pump? Sump? And what fluid is leaking?
    120k service (water pump, oil pump, oil pan)

    Quote Originally Posted by Roybatty View Post
    Don't use the prefabbed gaskets that they sell for oil pan! Only use the FIPG FTW.
    Definitely know better on that!

    Quote Originally Posted by AdamVR4 View Post
    I've never experienced "old" right stuff, but it's certainly possible that it can get old and no longer cure.

    Why are you messing around with Felpro gaskets?

    Go buy a new tube of the right stuff for $15 and seal this shit up. I've done ~15, 120K's and NEVER had a leak afterwards. I use NOTHING but OEM gaskets and The Right Stuff. Get both surfaces clean and dry and use liberal amounts of TRS on the oil pan flange. I put a fat bead on the flange then spread it over the whole surface with my finger (wear latex gloves). Once I've got a nice layer over the entire surface, I add TRS to the trouble areas (the bends). You need to be very careful during installation not to drag the mating surface across the girdle. Do some dry runs BEFORE putting TRS on the oil pan.

    There's absolutely no need to "retorque" anything after warm-up.
    Well...I work at a baxter auto parts, my boss "hooked me up" with some right stuff that was on the back shelf......dumb bastard, later I found out it was some old stuff that was given out as a sample, or recalled or somethin, wasn't sure, it was the grey kind and I've heard from others that it did the same to them, didn't cure.

    I was thinkin maybe Fel-Pro was causin the problems, and I wouldn't use TRS on water pump or oil pump, not with the small channels, it'd be too risky to end up with that stuff in the flow of things. I wouldn't think Fel-Pro is any different than OEM though...a paper fiber gasket, but I dunno...and I get'em at cost...but shit, if that's what it takes to have a leak free car again...I'll have no choice I guess...

    The Right Stuff is awesome...I can say that...no oil pan leaks lol

  6. #6
    Forum User
    Join Date
    Sep 2010
    Owner Since
    2002

    Posts
    1,668
    Thanks
    514
    Thanked 388 Times in 259 Posts
    Quote Originally Posted by Nihil View Post
    120k service (water pump, oil pump, oil pan)

    Well...I work at a baxter auto parts, my boss "hooked me up" with some right stuff that was on the back shelf......dumb bastard, later I found out it was some old stuff that was given out as a sample, or recalled or somethin, wasn't sure, it was the grey kind and I've heard from others that it did the same to them, didn't cure.

    I was thinkin maybe Fel-Pro was causin the problems, and I wouldn't use TRS on water pump or oil pump, not with the small channels, it'd be too risky to end up with that stuff in the flow of things. I wouldn't think Fel-Pro is any different than OEM though...a paper fiber gasket, but I dunno...and I get'em at cost...but shit, if that's what it takes to have a leak free car again...I'll have no choice I guess...

    The Right Stuff is awesome...I can say that...no oil pan leaks lol

    You're using felpro gaskets on the oil pump and water pump!?!?! No wonder you develop leaks. This makes me want to hit myself in the face.

    Use OEM gaskets with a VERY thin layer of RTV (I use TRS) on each side. Anything else is just begging for problems. A Mitsu master mechanic taught me this in 2004 as I WATCHED him do an oil pump swap (he used Mitsu OEM RTV).

    And for the love of god, in the future, can you please specify where the leak IS so the rest of us don't waste so much time trying to help you?
    Last edited by AdamVR4; 10-04-2011 at 01:01 PM.

  7. #7
    Secret Lurker Man! verified
    Join Date
    Sep 2010
    Owner Since
    7/10/06 or somethin

    Location
    Bend, Oregon
    Posts
    452
    Thanks
    13
    Thanked 20 Times in 14 Posts
    Well, I figured, I mentioned the 120k service, so everyone would know what's involved and where leaks were, though I suppose I didn't specify oil or water or both...sorry about that, but to clarify it is both...

    Also, upon disassembly, the gaskets weren't metal gaskets, this IS on a SOHC though, but I don't think that would matter...at least not on the water pump...I know I only go with metal gaskets if that's what stock is, which is why I never thought twice about felpro since the gaskets that were removed were fiber/cellulose...Someone did change the water pump once before me though, but never the oil pump and it had the general common fiber type gasket...

    I was thinking about that, using TRS thin coat on all gaskets, that stuff is magic, but from my understanding though, coating a gasket with anything sort of defeats the purpose of the gasket? So...couldn't you just use straight TRS and be just as affective, minus the fact it could squish out and clog or narrow passages? I realllly don't wanna do this for a fourth time just to have it fail AGAIN

  8. #8
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    Seattle, WA
    Posts
    163
    Thanks
    12
    Thanked 39 Times in 22 Posts
    Replace your bolts for water pump and oil pump. They like to stretch. Fairly common actually. Especially if overtorqued at some point in their life. When they stretch they will not retain the correct torque on them at all. This causes leaks almost always. Seen it more than once. Usually you can feel the bolt stretching but someone inexperienced might not notice. I keep a bin of these bolts (new) just for this reason.
    Dying ain't much of a living, boy.
    Josey Wales

  9. #9
    Forum User
    Join Date
    Sep 2010
    Owner Since
    2002

    Posts
    1,668
    Thanks
    514
    Thanked 388 Times in 259 Posts
    Quote Originally Posted by Nihil View Post
    Well, I figured, I mentioned the 120k service, so everyone would know what's involved and where leaks were, though I suppose I didn't specify oil or water or both...sorry about that, but to clarify it is both...

    Also, upon disassembly, the gaskets weren't metal gaskets, this IS on a SOHC though, but I don't think that would matter...at least not on the water pump...I know I only go with metal gaskets if that's what stock is, which is why I never thought twice about felpro since the gaskets that were removed were fiber/cellulose...Someone did change the water pump once before me though, but never the oil pump and it had the general common fiber type gasket...

    I was thinking about that, using TRS thin coat on all gaskets, that stuff is magic, but from my understanding though, coating a gasket with anything sort of defeats the purpose of the gasket? So...couldn't you just use straight TRS and be just as affective, minus the fact it could squish out and clog or narrow passages? I realllly don't wanna do this for a fourth time just to have it fail AGAIN


    Keep in mind I've never even seen under the hood of a SOHC, so someone correct me if I'm wrong...

    The water pump gasket is metal, the oil pump gasket is fiber. Always, always, always use a thin layer of RTV on both (entire) sides of the oil pump gasket. Yes, you can seal the oil pump with just RTV. I did it on my SL and I seem to recall maTT (3SX guy) saying he did the same thing back in the day. My choice though? OEM gasket + RTV.

    Be sure to apply RTV to the threads of the bolts that hold the oil pump on. Again, this was an instruction by the Mitsu mechanic, I've never taken the time to confirm that some (or any) of the threaded holes go into oil passages.

    On the water pump, a thin layer of RTV on the metal gasket around the coolant passages.

    I've never seen any issues with RTV squishing into the tiny passages on the oil pump housing. Again, apply a thin layer to both sides of the gasket -- we're not sealing an oil pan here

    I've never seen the oil pump or water pump bolts stretch, especially not to the point where they wouldn't hold torque or remain tight. You're only torquing them to what, 12 ft-lbs? Now, the small bolts that hold the cam caps on, I know from experience, will stretch like crazy if you over torque them.

    Anyway...

  10. #10
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    Seattle, WA
    Posts
    163
    Thanks
    12
    Thanked 39 Times in 22 Posts
    Quote Originally Posted by AdamVR4 View Post
    I've never seen the oil pump or water pump bolts stretch, especially not to the point where they wouldn't hold torque or remain tight. You're only torquing them to what, 12 ft-lbs? Now, the small bolts that hold the cam caps on, I know from experience, will stretch like crazy if you over torque them.
    Anyway...
    Yeah, happens quite a bit from my experience. Had two incidents of this very thing this year on some VR4s. I use a digital snapon torque wrench so maybe it is a bit easier to see them stretch. You can watch the torque go up and then drop right back off while they stretch. It is usually not every bolt holding on the oil or water pump but one or two. Which is enough to cause problems. Bolts are relatively cheap so I replace them w/o concern if there is question. Also had a tensioner bolt stretch this year too. Again, on a couple VR4s. These days I keep a selection of new ones ready to go as needed.

    Maybe it is the digital torque wrench that allows for more easily noticed? I dunno. But the difference is immediately noticed, and corrected, by getting new bolts in there that hold. 'voila, problem solved.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering