Nice sig picture, by the way.
Nice sig picture, by the way.
'92 3000GT Base ATX converted to MTX - Parted Out
'91 Stealth ES MTX - Fastest NA FWD at NG11 Drags - SOLD
'91 Stealth RT/TT Check out my blog
'10 Jetta TDI MTX - 6 speed: 50MPG Highway
Rest In Peace, My Brother SGT. R. Evans Taylor: Apr 23 '83 - Oct 14 '11
I never specifically mentioned anything about slipping the clutch, so not sure where that came from. On the matter, though - I do not advocate slipping any clutch (other than a carbon/carbon or similar) any more than absolutely necessary to get the car moving and the wheels spinning. Organic and Kevlar compounds will burn, glaze and chunk off with too much slip and metallic compounds will weld/fuse the disk to either the pressure plate and/or the flywheel or floater. Neither (metallic especially) are designed nor intended to be slipped any more than the absolute bare minimum to get the car out of hole -- riding the clutch out will kill either VERY quickly. They guys that are only getting 10-15k out of a clutch are slipping WAY too much. The solution to this problem is wheelspin; however, the caveat is wheelhop will absolutely break shit (more on this in sec) more so than a head-hook. The key to a good launch is coming out of the hole in an RPM range where the turbos are already lit with enough wheelspin to keep the RPM's in that range or above until 100% traction is achieved. There is a balance there, where the launch can be too aggressive and the wheelspin can be too severe (FWD and RWD guys know all about this). The upside to that scenario is while the launch and run is blown, your drivetrain is not. My method was to start with way too much tire pressure (40-45psi) so that wheelspin was easily induced, and then start backing the pressure down to more reasonable levels to suit the conditions that day. With this method, my launch RPM and clutch engagement stayed relatively static, and I made the adjustments to tire pressure first; this allowed for more consistency and repeatability. As for wheelhop - this is an evil that most times cannot be predicted or foreseen. The tendency to wheelhop (in my experience) varied greatly depending on track conditions/prep, temperature, etc... You simply have to train yourself to get out of the pedal as soon as wheelhop is induced. Drag radials will significantly increase the likelihood of wheelhop, and after lots of observation, I wouldn't really recommend them for a heavy AWD car any longer (on the track, at least). Solid/poly mounts won't really mitigate wheelhop specifically, but they absolutely help keep your drivetrain alive under launch conditions. A heavily-damped/stiff suspension will assist as well, as contrary to RWD platforms, you want to minimize the weight transfer in AWD. One of the worst things that happens (and these cars are very prone to it) is where all the weight transfers to the rear, it heavily squats, the front tires unload and attempt to spin and then you induce a front to rear oscillation of torque -- this is not only not an inefficient launch, but is very unhealthy for your drivetrain. Anyhey.... Enough of my ramblings on the matter for now.
RE: 6 speeds -- I think the case splitting is somewhat over-rated. A percentage of these fall into the 'shit happens' category (like busting one on the first pass) but a lot of the case failures at low to mid power levels are a result of poor technique, IMO. And again, the case failures seem to be somewhat new in the grand scheme. I never recall any of this happening back in the day. In fact, way back when, the 6 speed was considered indestructible compared to the 5 speed because OS and TC failures were almost unheard of, whereas the 5 speeds stripped/break OS and/or broke TC's. Case in point - I had a buddy back in the day with a '96 VR-4 that was running mid 12's straight BPU and cutting mid 1.6 with the occasional 1.5 60' and when we pulled his tranny due to loosing reverse (unrelated to racing) the OS and case were in absolutely perfect shape. I have never personally witnessed a 6 speed failure of any kind among the dozen or so cars that I was around when we were racing. In fact, the only 5 speed failure I witnessed was an 18-spline OS on the receiving end of a 6000RPM launch on a freshly broken in RPS 6-puck.
1993.5 Supra TT 6sp Hardtop -- old school 74MM setup: 10.4 @ 138MPH 1/2 mile - 166MPH - new setup #'s soon! [Previously 468WHP & 11.3 @ 125MPH stock twins]
1994 Supra TT 6sp -- 11.8 @ 118MPH basic BPU
1999 3000GT VR-4 -- 12.5 @ 108MPH 100% stock w/ Chromed ECU tune
2003 Denali XL -- Grocery Getter & Tow Rig -- Runs 13's! (mpg)
Formerly:
1994 Supra 6sp - 72mm, VPC, stock longblock -- 722WHP & 10.36 @ 139.5MPH
1993 Stealth RT/TT; 2003 Corvette Z06; 1997 3000GT VR-4; 2002 Corvette Z06;
1999 3000GT; 1992 Stealth RT/TT; 1993.5 Supra TT; 1993 3000GT; 1992 3000GT VR-4;
1998 Trans AM WS6; 1992 Talon TSi; 1993 3000GT VR-4; and many others..
Here is how you launch without breaking shit.
notice the wheelspin, these guys are not sidestepping the clutch on launch. Also check out the nifty AWD doing its thing.
Two things:
1) Slipping the clutch when you make boku power = bad as you've pointed out. Example: BenH fused his clutch to the flywheel once....not cool. Wheel Hop is the devil..there are ways to mod the suspension to counter it though.
2) The part of the 6spd that fails is the brace, and to date everyone that I know of with a mid to higher hp 6spd without a brace has killed at least one housing. You keep naming single examples of either yourself or a 'friend.' Sorry brother but there are a lot more that prove your examples to be the exception, not the rule.
Current Car:
2011 Chevrolet Corvette GrandSport
Cars Owned:
1992 Dodge Stealth RT (sold)
1992 Mitsubishi 3000GT VR4 #1 (parted)
1992 Mitsubishi 3000GT VR4 #2 (sold)
1993 Mitsubishi 3000GT VR4 #1 (KIA)
1993 Mitsubishi 3000GT VR4 #2 (sold)
1994 Mitsubishi 3000GT VR4 (sold)
1994 Mitsubishi 3000GT Base - awd/atx (sold)
1997 Mitsubishi 3000gt VR4 (sold)
2006 Pontiac GTO (sold/traded)
2008 Chevrolet Corvette 3LT (z51)
As I've previously stated, I provide feedback relative to my own personal experiences and those immediately around me, first and foremost. However, I have also been a watchful observer of this platform and those racing these cars for over a decade and have derived some of my opinions based on that data as well. So 'everyone you know' doesn't trump the hundreds of accounts of historical data clearly documented and discussed in the bowels of another forum, IMO. Just because I call out specific examples of a 'friend' doesn't mean my experienced is limited to that....
No not limited to that, but I don't think it takes into account the glaring obviousness of the issue at hand. If 6 out of 10 people that race their car hard have failures, it might just be a problem Or dumb luck. Being that the statistical probability that it's an issue is higher than 50% therefore I can't turn a blind eye and chalk it up to a bad experience.
I would firmly disagree with a 60% historical failure rate (or even a fraction of that), but we can just leave it at that.
6spd w/o a BH brace isnt a matter of IF but WHEN its gonna fail. Assuming the car has any power and good tires. Track prep means a lot too, probably more than anything else. Ive raced on some tracks where your shoes stick to the track and my 275 DR's didnt even chirp cutting a high 1.5 60ft and some where i could spin all of 1st gear and kick the ass out grabbing 2nd...
When i broke i usually never made it to the 60ft mark under power. Just a snap or a metallic bang on launch and i only broke when the track was very well prepped. I NEVER broke a part when i was able to get wheel spin.
Jason
I would have to disagree that the failure rate is that high. Furthurmore, I dont think anyone has ever posted a thread involving putting a transmission back together like a crashed airplane to investigate the reasoning for it falling out of the sky. The subject matter has always been taboo, and the last time I checked none of the guys breaking shit are professional racecar drivers either. The way I see it, only thing that separates everyone is the driver and said launch technique.
|
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
|
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
|
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
|
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Bookmarks