Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Idle Help Please

  1. #1
    Forum User
    Join Date
    Nov 2013
    Owner Since
    2013

    Location
    Stockton, England
    Posts
    54
    Thanks
    2
    Thanked 2 Times in 1 Post

    Idle Help Please

    I've just started the tuning of my 3000GT engine in my kit car running a Chrome ECU. Starting with the idle setting as recommended in the guide and fell at the first hurdle. With the idle wire connected the base idle is low so I adjust it up to 850 (as set in the ecu) and it runs quite smooth. As soon as I disconnect the wire. idle goes up to 1100rpm. So I figured there must be something wrong with the idle control valve. Took it out and sure enough, pins 4-5 have no resistance. I made sure the valve is fully out and refitted it but left the connector off; still the same problem.
    Any ideas folks?

  2. #2
    Member Not Verified
    Join Date
    Nov 2010
    Owner Since
    2003

    Posts
    2,062
    Thanks
    112
    Thanked 272 Times in 206 Posts
    Engine temp fully warm and a/c off?

  3. #3
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    The ECU primarily uses timing to make rapid idle speed changes. The IAC is used for preprogrammed large changes. until you have a working IAC, I'd just leave it unplugged and turn the BISS in until you get an acceptable warm idle speed. Without the ability to adjust the airflow, I suspect your idle is increasing when it puts the timing back in...


    Real Performance Automotive (541)816-4500 www.FB.com/RealPerformanceAuto

  4. #4
    Forum User
    Join Date
    Nov 2013
    Owner Since
    2013

    Location
    Stockton, England
    Posts
    54
    Thanks
    2
    Thanked 2 Times in 1 Post
    Yes engine warm and AC off.
    Why would it add timing at idle speed though?
    I'll try plugging the standard ecu in to see if it still does it.

  5. #5
    Member Not Verified
    Join Date
    Nov 2010
    Owner Since
    2003

    Posts
    2,062
    Thanks
    112
    Thanked 272 Times in 206 Posts
    Base idle mode locks timing at 5 degrees, while the actual timing at idle is closer to 12. It's a diagnostic mode for certain things, so if you are setting idle speed with the IAC locked you need to set it with the ECU in normal mode.

  6. #6
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    Quote Originally Posted by knights19 View Post
    Yes engine warm and AC off.
    Why would it add timing at idle speed though?
    I'll try plugging the standard ecu in to see if it still does it.
    Like I said, the ECU uses timing to control idle speed... When you ground the connector, it fixes the timing and IAC to a set point so you can establish the baseline. When you unplug the connector, and it feeds that timing back into it, and the IAC is unable to move, you get an increased idle speed...

    Until you have a working IAC, I'd ignore the set connector, and simply set the warm idle to a livable point in normal operation.

  7. #7
    Forum User
    Join Date
    Nov 2013
    Owner Since
    2013

    Location
    Stockton, England
    Posts
    54
    Thanks
    2
    Thanked 2 Times in 1 Post
    Seems stable now.
    Can you advise on the attached?
    I'm getting ignition cut due to knock count but I suspect my base noise is high as the engine is near solid mounted with a Ford gearbox attached and the rear diff mounted to the side of the engine.
    Is it a multiplier issue?
    14-1-19 ign cut.jpg
    14-1-19 ign cut with knock sum.jpg
    14-1-19 CSV.jpg

  8. #8
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    There have been instances of false knock reported, but it's pretty rare... The factory algorithm is pretty good about picking out what is real knock.

    How much timing is being pulled? And what knock sum are you seeing?

  9. #9
    Forum User
    Join Date
    Nov 2013
    Owner Since
    2013

    Location
    Stockton, England
    Posts
    54
    Thanks
    2
    Thanked 2 Times in 1 Post
    Knock voltage seems low in the data above, is that correct?
    I get 8-9 counts but when it starts, it doesn't stop. Even when I cruise afterwards the sum stays up there and the timing stays at 5 degrees as soon as it sees it.

  10. #10
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    Quote Originally Posted by knights19 View Post
    Knock voltage seems low in the data above, is that correct?
    I get 8-9 counts but when it starts, it doesn't stop. Even when I cruise afterwards the sum stays up there and the timing stays at 5 degrees as soon as it sees it.
    I think you have an electrical problem somewhere... 7-9 counts is the default output by the ECU when there is a knock sensor problem. It will not flatline the timing, It puts it into the low octane map. If it's seeing real knock, it only pulls a a small amount of timing per count. 9 counts of real knock is pretty insignificant in the timing map (you can see how much, and modify the number in the knock table)

    I wonder if you don't have a short to ground in your timing set connector..?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering