Whole rear end, front cross member, rear subframe, everything is out. I'm thinking maybe a combo of jacks and the 1000lb dollies. Might be enough to move it out at least.
Whole rear end, front cross member, rear subframe, everything is out. I'm thinking maybe a combo of jacks and the 1000lb dollies. Might be enough to move it out at least.
Mods: 2g 3k body conversion, 2g Brake upgrade, Rota P45R rims
Projects: Interior sound deadening, 14Bs, forged bottom end, custom radiator and sound mounts
4x4 wood across the mount points for the subframe. cut the 4x4 down so you can use the mounting bolts to secure. Use 4 of these Mover's Dolly
Help them, for they know not that which they do not know!
CoopKill's Mistress Makeover Thread!
"Punk, Nutswinging, Small Time, Asshat, Monkey, Jerkoff, Loser that rides on other peoples accomplishments!" ..
Well, I've had a steady stream of contractors and such coming through today to evaluate the pipe issue. Specialist coming tomorrow to basically scope the area and see exactly where the leak is occurring, but a few contractors think they can get to the leak by removing the cabinetry in the kitchen and cutting through the floor there rather than tearing the garage up.
Didn't get much done in the garage because of that, maybe 45 minutes or so wire wheeling the engine bay a bit. Going to fill in holes and stuff tomorrow and try to get the bay done. Thinking that if I have to move the car, I MAY try dropping the car down onto some wood that is resting right on the concrete and just jacking up each end individually to shove it over. Time consuming, but pretty much what ends up happening if the moving dollys break. No time to order metal wheel skates or anything and have them shipped here.
On the bright side, I am moving closer towards getting all my bushings done in poly. Just a handful left to go.
Dropped off torque converter at a local place, "Champ Converters" for a re-stall.
1992 Kilder Green VR4 - First 4G swap in a 3S. 2.0, auto, awd. 9.65 at 143mph. Now LS swapped. 8.52 at 162.
No sense taking it to a shop..If it's stalling, you just gotta get better working that clutch pedal..
No worries champ.
Lol. Me too. Car task for tomorrow is too call machine shop. Would love to get my parts back before Xmas so I can get work on assembly/dissambly/reassembly a few times to check piston to valve clearance at carrying intake came advancements.
Bryan, next time you get a ride, I hope to make a believer out of you for going clutch-less, even in the twisties![]()
Ugh still haven't pulled my motor yet. What I get with using crap tools.. Gonna have start over buying my own. But only a few things left before its ready to come out. If some things go my way I could have it out tomorrow and start cleaning up the bay and figuring out what everything is. Has anyone else seen a car with six gauges three stock one and a gauge pod with the same three gauges in it lol. Don't know what PO was thinking. They aren't even hooked up yet
Are You Not Entertained?! Are You Not Entertained!
1992 Dodge Stealth R/T- sold
1994 Mitsubishi 3000gt VR4
1991 BMW e30 318is
Picked up a fresh bottle of Argon![]()
|
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
|
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
|
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
|
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Bookmarks