Page 2 of 9 FirstFirst 1234 ... LastLast
Results 11 to 20 of 90

Thread: 19T + e85 too much for stock bottom?

  1. #11
    Forum User Not Verified
    Join Date
    Jan 2011
    Owner Since
    2003

    Location
    Hell Paso, Texas
    Posts
    129
    Thanks
    15
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by kywhitelightning View Post
    Actually, it was too little methanol. I found leaks later that I never posted about. That is why it knocked and the knock bent the rod. The push on type fittings that all the injection places like to sell are freaking junk. I have converted the whole system to brass compression style fittings and no more leak issues. Prolonged 500+whp will eventually break things but that incident was because of the lack of octane.

    Jeff
    At what boost level were you injecting methanol (start and full), what mixture were you using and how much knock were you seeing? What was your remedy?
    STEVE-O
    '92 VR-4 - '99 Front End Conversion - Galaxy White

  2. #12
    Low & Slow verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Fortson, GA
    Posts
    577
    Thanks
    25
    Thanked 39 Times in 29 Posts
    I think it started around 8psi and was full on by 22psi. It was a 10W/90M mix. Knock counts were mid to upper teens IIRC. I know it pulled at least 5* of timing out.

    The remedy was replacing EVERY push on type fitting with a brass compression style fitting. The newer pumps that Snow sells have those stupid fittings molded into them so I began ordering everything I get from Devils Own.

    This wasn't the first time it had leaked from those fittings as I had replaced quite a few of them prior to that incident. It was, however, the last time I ever had one on my car.

    Jeff

  3. #13
    Member Not Verified
    Join Date
    Sep 2010
    Owner Since
    '09

    Location
    Myrtle Beach
    Posts
    2,604
    Thanks
    120
    Thanked 131 Times in 95 Posts
    Jeff, that just makes me nervous. Even though I'm not spraying that much the push-lock fittings are starting to scare me after hearing your story.

  4. #14
    Forum User Not Verified
    Join Date
    Jan 2011
    Owner Since
    2003

    Location
    Hell Paso, Texas
    Posts
    129
    Thanks
    15
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by mb3000 View Post
    Jeff, that just makes me nervous. Even though I'm not spraying that much the push-lock fittings are starting to scare me after hearing your story.
    Me too!!!

    In fact, just curious Jeff, but how has your experience with using more than 50%meth been? Maybe I'm just being a little chicken but I haven't used more than 50. I'm using the AEM kit
    Last edited by heptone182; 02-06-2014 at 11:24 PM.

  5. #15
    There will be Blood! verified
    Join Date
    Sep 2010
    Owner Since
    1997

    Location
    In Sane!
    Posts
    4,677
    Thanks
    1,081
    Thanked 449 Times in 331 Posts
    Looks like I will have 6 Snow nozzles for sale! Another $200~ in parts needed. lol

    Help them, for they know not that which they do not know!
    CoopKill's Mistress Makeover Thread!
    "Punk, Nutswinging, Small Time, Asshat, Monkey, Jerkoff, Loser that rides on other peoples accomplishments!" . .

  6. #16
    SDSU Alumnus verified
    Join Date
    Sep 2010
    Owner Since
    Nov 2006

    Location
    Chula Vista SD, CA
    Posts
    484
    Thanks
    13
    Thanked 14 Times in 13 Posts
    I have to admit that I am curious to see how the Clevite 77's held up after a very hard 7-8k of DD miles. The OE forged crank is obviously dunzo lol. FWIW, my OCI's were very clean each time even from the break-in period; I use M1 15W-50 with a 7+ quart capacity.

    The interesting thing about the push-on fittings that were mentioned is that some people still have success using them "reliably" at similarly high levels, such as Matt and Eric with dual-nozzle setups. Experiences do vary of course. I really like DO's block for DPMI =] that sumped reservoir too! AIS always had nice braided setups available.
    3/S Street Tuner San Diego's Panda VR-4 v.3 w/ 38psi (peak) on E85+Meth | 3094 lbs as of 7/2/19

    '92 VR-4 - Fully built, AEM EMS S2, MHI EVO3 16G's, suspension, and corner balancing | '10 EVO X SE | '04 EVO VIII SSL
    4/1/21 - "retuned" est. 570AWHP VD SAE (580 U/C | second gear | 88°F) holding ~30psi (more boost & less timing still... hehe)
    On the side (v.4): IPS single turbo kit w/ GReddy 70mm, BC 3.4 billet stroker crank, BC gears, Italo billet oil pump gears, etc.

    "There are no secrets better kept than the secrets that everybody guesses."

  7. #17
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Quote Originally Posted by kywhitelightning View Post
    I think it started around 8psi and was full on by 22psi. It was a 10W/90M mix. Knock counts were mid to upper teens IIRC. I know it pulled at least 5* of timing out.

    The remedy was replacing EVERY push on type fitting with a brass compression style fitting. The newer pumps that Snow sells have those stupid fittings molded into them so I began ordering everything I get from Devils Own.

    This wasn't the first time it had leaked from those fittings as I had replaced quite a few of them prior to that incident. It was, however, the last time I ever had one on my car.

    Jeff
    Thanks for your info btw, I too am going to move to these style. I take my intake pipe off often and found that the constant connect/disconnected "wore" out the hose and it wouldn't seal as tight. Eventually to the point of it popping off easily. I imagine similar things can happen with just the vibration/movement of the engine.

  8. #18
    Low & Slow verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Fortson, GA
    Posts
    577
    Thanks
    25
    Thanked 39 Times in 29 Posts
    The nozzles aren't the problem, it's the push on fittings.

    Keeping the hose straight prior to going in is one way to combat it but, like mentioned before,mine were on and off a lot.

    The best advice i can give about them is to check on them often. I still flow test my system very frequently. The compression style fittings reseal well after disconnection too. Plus, lowes has everything on the shelf needed to convert. I think I have found the flow limit with the 1/4 compressin ittings at around 1600ml/mi. I'm upgrading the feed line to 3/8 which will prove it. Right now everything flows through one 1/4 compression fitting.

    Jeff

  9. #19
    Low & Slow verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Fortson, GA
    Posts
    577
    Thanks
    25
    Thanked 39 Times in 29 Posts
    Quote Originally Posted by bboyalan View Post
    I have to admit that I am curious to see how the Clevite 77's held up after a very hard 7-8k of DD miles. The OE forged crank is obviously dunzo lol. FWIW, my OCI's were very clean each time even from the break-in period; I use M1 15W-50 with a 7+ quart capacity.

    The interesting thing about the push-on fittings that were mentioned is that some people still have success using them "reliably" at similarly high levels, such as Matt and Eric with dual-nozzle setups. Experiences do vary of course. I really like DO's block for DPMI =] that sumped reservoir too! AIS always had nice braided setups available.
    Why are you using such high viscosity oil?

    Jeff

  10. #20
    Low & Slow verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Fortson, GA
    Posts
    577
    Thanks
    25
    Thanked 39 Times in 29 Posts
    Quote Originally Posted by heptone182 View Post
    Me too!!!

    In fact, just curious Jeff, but how has your experience with using more than 50%meth been? Maybe I'm just being a little chicken but I haven't used more than 50. I'm using the AEM kit
    The less water I ran the less the car bucked. I now run 100% methanol all the time. I recently purchased a 55gal drum of m1. At ~$4.50/gal it nearly can't be beat.

    Jeff

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering