Page 5 of 20 FirstFirst ... 3456715 ... LastLast
Results 41 to 50 of 195

Thread: Now Another Problem.....

  1. #41
    The one. The only. verified
    Join Date
    Sep 2010
    Owner Since
    August 28, 2002

    Location
    SWPA
    Posts
    4,042
    Thanks
    182
    Thanked 699 Times in 529 Posts
    Quote Originally Posted by GRSHOPR View Post
    OK, so by process of elimination, I figured out which it was. I then traced the wire. There is indeed voltage when the key is to START. And to remove any issue, I also bypassed the relay. There is indeed power to pin 5 on the socket as well, and in turn, via the bypass, pin 2. But there is still no power to the fuel pump. I don't here it priming or anything. What's next??
    The pump doesn't prime. As I said it only runs when you are cranking the engine.

    [06-05, 19:29] OhioSpyderman: Brian, finding a woman is NOT the answer, you need to shop for a good VACUUM

  2. #42
    OK, so I shouldn't be hearing anything then anyways. I found another issue. Under the dash, by the passenger right knee rat's nest of wiring, I trace the power going from the relay to a plug that wasn't plugged in. Apparently, they changed the plug types from a normal 7 or 9 pin plug to one of those heavy duty ones for power transfer. I spliced in the correct plug, although there were two extra wires on the plug I spliced in that don't fit anywhere on the harness. No big at that point, because the pin I tracked the pump power to was spliced in and good to go. So where does the power head next?? Straight to the pump assembly? There still isn't power to that plug. And I thought the car can't turn over if that plug isn't plugged in?

    On a side note, I found another plug in the center console, branches off right where the ECU plugs branch as well. It's black, has 4 pins, is covered in foam. What does that go to??

  3. #43
    And I found something else odd. Somewhere between the pump and that connector, the wires change color?? The side coming from the relay, the power wire is blue and black. Leaving the connector, towards the fuel pump, it's black and red. And back at the fuel pump it's black and blue again?? Something isn't jiving here. I was thinking for a minute that maybe I spliced the wrong plug in, but looking at the original engine harness, that's the only possible plug that it could be. Plus the wires matched up. That can't be a coincidence. But it doesn't make sense why it would change colors and then change back. Or even WHERE it would do that.

  4. #44
    OK, so I looked through my diagrams again. Here's what I've found.

    Below is a 1991 diagram, which is what I'm using for a harness, and it's a little more in depth than the next pic, so it's a good start for comparison. Notice how the wires all the way back are b-l, or black and light blue, all the way to the fuel pump. I spliced in this morning what I'm pretty sure is C-30. This pic shows C-30 as being a 6 pin connector, which it was originally, on this 1991 harness. Which means I somehow have to find C-34, correct?



    OK, so next is a pic of the 1994 diagram, since that's what the rest of my car is, aside from the engine harness. This diagram doesn't specify how many pins C-30 or C-34 have, so I think I'm going to have to take it on faith and luck that C-34 has the same number of pins between the generations. My bet is that I'll still have to splice in the newer connector. Notice also, how this diagram shows the wiring going from b-l (black and light blue), to b-r (black and red wire), which corresponds with what I'm seeing under the dash. Does all this seem logical and correct?? If not, please set me straight.


  5. #45
    Here for the party Not Verified
    Join Date
    Sep 2010
    Owner Since
    2006

    Location
    Canaan NH
    Posts
    1,710
    Thanks
    364
    Thanked 106 Times in 87 Posts
    I would use the diagram to run your own wires to the pump.

  6. The Following User Says Thank You to CoreyB For This Useful Post:


  7. #46
    My only concern is what does the dashed line around the fuel pump mean??

  8. #47
    OK, so I said screw it, spliced anyways, and it's running!! Almost. It doesn't quite run on its own yet. If I turn the starter over for about 30 seconds, it builds up to about 2k rpm, but doesn't keep itself going yet. Is that normal?? It sounds like it's slowly building itself up to running, the combustions are getting deeper sounding, and building more quickly. But then I think the starter started to smoke, so I'm going to let it cool down for a bit before I try again. Is that normal?? Can a starter even smoke?? What should I be looking for to happen in the start-up process?? Admittedly, I haven't really dealt with an engine that has been sitting/new before. Not sure what to fully expect from this whole process. Any advice?? Thanks.

  9. #48
    Here for the party Not Verified
    Join Date
    Sep 2010
    Owner Since
    2006

    Location
    Canaan NH
    Posts
    1,710
    Thanks
    364
    Thanked 106 Times in 87 Posts
    Can you check your fuel pressure ? Sounds like its to low. You should check the voltage at the pump while cranking as well.

    You can also connect the blue terminal by the battery to the positive battery terminal and see if the pump is running. Thats the test terminal for the pump.

  10. #49
    Quote Originally Posted by CoreyB View Post
    Can you check your fuel pressure ? Sounds like its to low. You should check the voltage at the pump while cranking as well.

    You can also connect the blue terminal by the battery to the positive battery terminal and see if the pump is running. Thats the test terminal for the pump.
    Are you sure about the blue terminal??? I connected it, and it threw a bunch of CELs, and it sounds like the MFI clicked, but I didn't see any power at the fuel pump.

  11. #50
    Here for the party Not Verified
    Join Date
    Sep 2010
    Owner Since
    2006

    Location
    Canaan NH
    Posts
    1,710
    Thanks
    364
    Thanked 106 Times in 87 Posts
    Yeah. Something must be wrong. The blue one is for the fuel pump and the brown one is for setting ignition timing. Are you sure you jumped it to positive and not negative ?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering