Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 36

Thread: Rear Steering Rack Rebuild

  1. #21
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    I have no doubt I could draw up the needed tool in AutoCAD. I just think the small (3mm) pins would break off before anything would turn on that end. Either something interferes with turning the end cap or it's welded shut. There's a right angled block with a hydraulic connection so I was thinking that piece was threaded in to the cylinder housing and might be blocking the end cap from turning however the right angle piece doesn't budge either.

  2. #22
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    Well, I didn't use a big enough BF pipe wrench after all

    I found a hydraulic shop today and brought in the power cylinder. They used a really huge pipe wrench and opened it up and replaced the shaft seal for FREE !!

    It was already completed when I returned and I asked him how he did it and he demonstrated that it functions properly and has no leaks. So, my core unit is fixed already and I have the one on the car to take out and fix. If this core unit can be cleaned up enough I might put it on my car.

    I didn't get the PN of the seal they put in there but I do have the one they pulled out. It states SKY-18N on the seal but google returns nothing on that. Anyway I'll probably take mine down there and see if I can get it done for free too!

    Mod list (scroll down the page)
    JNS Engineering has your Spyders covered (and uncovered too!!)

  3. #23
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Ask if you can get seal PN info! That would be awesome for those looking to do the same in the future.

  4. #24
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    Quote Originally Posted by Toni View Post
    Ask if you can get seal PN info! That would be awesome for those looking to do the same in the future.
    Yes, I will try. The seal is kind of similar to what we have for the cams and transmission shafts, not like an O-ring at all.

    I was thinking the way to open up the power cylinder is to do it on the car when it's still bolted to the subframe. It takes a pretty huge vise to hold it otherwise.

  5. #25
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Do you think it's similar to anything in the front rack? I've rebuilt those a couple times but I imagine they are different pns.

  6. #26
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    Nope, just looked at the front rack rebuild wiki and nothing there looks like the seal in the power cylinder. I'll get the info on it next time though.

  7. #27
    Member Not Verified
    Join Date
    Sep 2010
    Owner Since
    2008

    Posts
    883
    Thanks
    14
    Thanked 34 Times in 23 Posts
    Good info. I don't plan on deleting my rear steering, so any info to rebuild them if needed in the future is gold!
    -Benn
    Master Elite KIA Technician
    Past> Level 3 Chrysler & Bronze level Hyundai
    1994 3000GT VR4 - #175 Black/Black 99 VR4
    2013 135is - 1988 Toyota Supra Turbo - Hers
    Follow my build thread here

  8. #28
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    I have all the details on the seal

    I went back to the hydraulic shop and found out what the original seal is and what the replaced it with. I bought a couple of seals so I have one for my power cylinder and I have a spare one. Haven't been able to locate an on-line source for these though. I may go setup a group buy on these seals.

  9. #29
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    What I know is the original seal is Nitrile Rubber (aka NBR or BUNA-N) and the dimensions are 18mm inner and 26mm outer and 5mm thick. Essentially a small rubber doughnut.

    The profile of the seal is called SKY.

    The shop I used installed new seals of a different profile. The ones they used were Polypak Type B which is similar to SKY but capable of higher pressure sealing. The Polypak technology uses what they call an energizer ring kind of like an O-ring to support the lips that seal against the rod and the bore.

    I bought two extra seals from them and plan to take my power cylinder apart and replaced the seals. I plan to leave the cylinder mounted in the car and use a large pipe wrench to unscrew the end cap after removing the tie rods.

    I never could open the old cylinder because I don't have a vice and couldn't get a good grip on the end cap.

    Anyway if you have a southern car that isn't rusted to shit there is a way to keep AWS and its fairly inexpensive. Just replace the seal(s).

    BTW nitrile rubber is very good at sealing hydraulic cylinders however it is not expected to retain its properties for 20 years. I don't think we could fault the designers one bit for using it.

    I've googled extensively for metric rod seals and have come up empty for on-line ordering. What I have found so far is:

    CRC Seals: MPP-018.0x026.0x05.0B
    Hydraulicseals.com.au: SKYM-018026-05

    I haven't tried contacting them by phone.

  10. The Following 3 Users Say Thank You to Jimvr4 For This Useful Post:


  11. #30
    Member Not Verified
    Join Date
    Sep 2010
    Owner Since
    2008

    Posts
    883
    Thanks
    14
    Thanked 34 Times in 23 Posts
    This should be stickied or something for the future!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering