Page 1 of 4 123 ... LastLast
Results 1 to 10 of 33

Thread: Rebuild Cost Range

  1. #1
    HID Retrofitter Not Verified
    Join Date
    Oct 2010
    Owner Since
    2004

    Location
    Cupertino, CA, USA
    Posts
    123
    Thanks
    13
    Thanked 1 Time in 1 Post

    Rebuild Cost Range

    Well, I need to start preparing to do something about the fact that my car absolutely will not pass smog inspections anymore. I was able to have it pass one last time late last year, but now it fails highly over the limit of HC's, and WAY over the limit of NOx. I can see puffs of blue smoke behind me when the light turns green, if the car sits too long while warming up (this has pointed towards bad VSS from what I have learned most of the time), it has a small coolant leak that I'm told is happening somewhere around the thermostat housing, my data logger has pointed out (9) for knock at higher rpms with wide open throttle (does that stand for how many counts of knock has been found?) and I have maybe 210xxx miles on the car. I have been thinking either I'll just upgrade to a JDM Debonair 6g74 engine, or rebuild my stock engine within the next 2 years, but I don't know how much that could cost to pay someone to do it for me. I know a couple people that might be able to do me a favor and do it cheaper than most shops I know, but I still have no idea. Is there anyone who has been in my predicament that might be able to give me an idea of what I could be in for based off that info?

    There are good cars that get you from point A to point B, and then there are great cars, that get you into trouble.

  2. #2
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    Well without knowing local labor rates, it'd be hard to pin down what they'd charge to do VSS, but there's a variety of things that can be checked. You could look into having the fuel injectors replaced/serviced (Probably at least 70 bucks) which could do quite a bit to help with the HCs. EGR could also be shot, contributing to high NOx count and that is a distinct possibility given mileage and age. Fixing a coolant leak by the coolant housing is very easy and can be done with either gaskets or RTV (or both). I wouldn't bother with a JDM swap unless I could afford to tear it down to inspect it and possibly rebuild it. There's no guarantees that what you purchase will be in better shape than your current motor.

    As far as rebuilding, provided no damage to crank, cams or heads, you could probably get it all done for less than 3k with labor if you pay a shop to do it with a 120k (since you're coming up on that time). Mine ran around 1800 (me doing the work) for hoist, stand, machine shop honing the cylinders and flywheel, plus gasket kit, OEM 120k parts and new clutch.
    Mods: 2g 3k body conversion, 2g Brake upgrade, Rota P45R rims
    Projects: Interior sound deadening, 14Bs, forged bottom end, custom radiator and sound mounts

  3. #3
    HID Retrofitter Not Verified
    Join Date
    Oct 2010
    Owner Since
    2004

    Location
    Cupertino, CA, USA
    Posts
    123
    Thanks
    13
    Thanked 1 Time in 1 Post
    I believe the average labor rates here from independent shops to dealerships costs from $100 - $120 per hour.
    It probably doesn't make that big of a difference, but I just remembered that my mileage is actually very close to 225xxx miles. Also that is everything that is wrong with the car that I have seen, and it has been well taken care of it's whole life. Sometimes it feels like it's not as powerful as it used to be, but I don't know if that's just because I have gotten used to it or not.

  4. #4
    HID Retrofitter Not Verified
    Join Date
    Oct 2010
    Owner Since
    2004

    Location
    Cupertino, CA, USA
    Posts
    123
    Thanks
    13
    Thanked 1 Time in 1 Post
    So from the sound of it, it will be more costly to put in a 6g74, knowing we can't trust it to be in perfect working order before using it. A lot of the JDM 6g74 engines I'm finding cost between $2400 and $2800!

  5. #5
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    Not saying that it's always the case with a 6g74, but I wouldn't buy one expecting it to be in mint condition. I would at least do a 120k to it for peace of mind. Some guys get lucky, others don't. I don't want to waste a 3k investment in an engine though.

    Anyhow, you could do a compression check. Your rings could be worn. This would reduce power and allow oil into the combustion process. You can check it with a compression gauge, numbers are listed in the service manual for what they should be. If they are low, you can put a very small amount of oil into the cylinder and if it brings pressure up would indicate rings. If the rings are good, then you could probably skip rebuilding the bottom end so long as you have good oil pressure. If the rings are good, then take it to a shop, have the VSS replaced (or you could do it yourself if you're mechanically inclined and have the patience and tools). The coolant leak by the thermostat is easy to remedy with new gaskets or RTV. Fuel injectors could probably use a good servicing or replacement, and clean the EGR system out (carb cleaner generally works well here). By no means is this an all-encompassing solution, but it may be enough to squeeze you through inspection on the cheap for now.

  6. #6
    I don't bite
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Southern IN
    Posts
    1,996
    Thanks
    59
    Thanked 98 Times in 80 Posts
    Do the VSS yourself. There are plenty of good vids online. A 6g74 will need VSS also. They are usually fairly old engines also that have been sitting around in a warehouse for who knows how long. They also rarely have been services well so oil control rings will be gummed up and make you smoke also. Just fix the problems you have. Doesn't sound that costly.
    1992 Kilder Green VR4 - First 4G swap in a 3S. 2.0, auto, awd. 9.65 at 143mph. Now LS swapped. 8.52 at 162.

  7. #7
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    David, take the car to Clark's. They did my machine work and can probably do a complete rebuild for under $5k. They did a 3S for that recently. I would trust Steve completely to address what it needs

    Mod list (scroll down the page)
    JNS Engineering has your Spyders covered (and uncovered too!!)

  8. #8
    HID Retrofitter Not Verified
    Join Date
    Oct 2010
    Owner Since
    2004

    Location
    Cupertino, CA, USA
    Posts
    123
    Thanks
    13
    Thanked 1 Time in 1 Post
    I could do it myself maybe after I had the tools, and if I had the time. So more than anything, that's why I have to pay someone.
    Maybe hopefully I don't have to have a full rebuild, and I can do the 3.5 swap later.
    Awesome Jim! Is Clark's just an engine builder shop or do they do repair work as well?
    Last edited by 3000GTPro; 07-31-2013 at 12:33 AM.

  9. #9
    1993 rt/tt Not Verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    wa state
    Posts
    813
    Thanks
    82
    Thanked 181 Times in 119 Posts
    how much really depends on you...

    ...i dare say most of us that rebuilt, spent a whole chit-ton more because once you get in there, its a whole lot easier to justify replacing this or that since you have things torn down. I know my own budget nearly doubled
    if you cant fix it with a hammer...then you have an electrical problem


  10. #10
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    Quote Originally Posted by wingnut View Post
    how much really depends on you...

    ...i dare say most of us that rebuilt, spent a whole chit-ton more because once you get in there, its a whole lot easier to justify replacing this or that since you have things torn down. I know my own budget nearly doubled
    Same here. Mine was supposed to be cams, rocker arms and 120k...Ended up checking out the bearings, which were totally shot and needed replacing. Then I decided to upgrade to a forged crank rather than polishing my cast because you know..already in there. Decided to get my 9Bs turned into 13Ts instead of rebuilding because I already had them out and the cost fairly close. Ended up switching to 3g lifters while I had it all apart. Picked up a front mount because "it makes more sense to do it now with all this." Picked up a Chrome ECu because "well..mine is 20 years old.." Then picked up Evo560s because "the flash can support them and my stock 360s have 170k on them). Heck, reringed the block (even though I didn't need to) so that I could go ahead and have it hot tanked since I already had it almost completely torn apart for the new bearings and crank..

    In truth, it would probably run you 3k either way. It's just how much do you get for your 3k? For me, selling old parts as I took them off and wheeling and dealing with parts is the only thing that kept this even remotely close to budget and even then I more than doubled my initial budget of 1.2k.

    in short, this is what ends up happening if you build it yourself


    A shop will do exactly as they need to do, and nothing else. Which may or may not work out for you if anything else goes wrong later. A complete rebuild for 5k may be a better idea for a shop.
    Last edited by sergechronos; 07-31-2013 at 01:33 AM.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering