Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: Disassembly: Lean Spool

  1. #1
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts

    Disassembly: Lean Spool

    Got side tracked for a bit while going thru the peripheries tonight. Bit 00 of periphery 1 in the periphery table is labeled as something called Lean Spool.

    I like Merlin's description best of what exactly this does.

    Quote Originally Posted by Merlins ECUFlash EVO Tuning Guide
    LEAN SPOOL is a tuning enhancement Mitsubishi employ to reduce the turbo spool time. A gasoline engine will produce hotter exhaust gas and more power at an AFR of 12.5:1 than 10.5:1. It achieves this by running a leaner AFR duing the rapid engine acceleration period than is set-out in the fuel map and in the process produce more torque. All of which results in quicker on-road car.
    So when I was peaking thru the code over the weekend tracing down how IPW is calculated I stumbled on this area of the code. There were 4 table references but they pointed to an empty table. Oddly though, there were 2 axis references and they were populated with a header and values! 3 of the tables shared 1 axis with 14 elements and the 4th had only 7. The unit of measure was RPM.

    Well tonight, I stumbled across this area of code again tracing periphery 1. Digging deeper into the logic, it came very clear what exactly this section of code was doing. Brought out the DSM disassembly and sure enough, the logic is identical! Lean Spool!

    Enabling bit 00 alone won't do anything. Just lag the processor unnoticeablely slightly as it reads thru this code, goes to the empty table look up and adds 0 to its IPW calculation.

    So what I did was create 4 tables in open memory, link them into the code and populate their values. Here's the result.



    Lean spool starts at 3000rpms and stops at 6000rpms. These were the values already programmed in memory. It's best to edit these values to match when your turbos first start to spool. The default value in the code is 3000rpms, but on most TD04 turbos, you might want to set this to closer to 2200rpms. I don't see any point in editing the coolant value.

    The Lean Spool Load table is the point above which lean spool will activate. Again, since these values are tuned for the more laggy TD05 turbos, you might want to drop them to something more conservative. My stock 98 sees 1psi at about 75-80 load in 3rd gear WOT.

    The Lean Spool AFR table is how much leaner your AFR will be off the High Octane fuel table. If you want to run .5 AFR leaner, then set the AFR in this table to .5 AFR leaner than the AFR in your fuel table. I wouldn't go past 14.7 unless you enjoy playing with fire.

    The Lean Spool Trailing Time - Rich Side table controls the time of Lean Spool operation through the RPM band. The units you see in the table are how long it will take to return to the normal High Octane fuel map. You'll have to play around with this to see what works best for you. The values populated here are the stock DSM values.

    The Lean Spool Trailing Time - Lean Side table controls the time to go from the High Octane table to the Lean Spool AFR table. Again, these are the stock DSM values.

    There are a couple other values not pictured. One is the AFR MAX value (16.1 by default) and the other is the AFR Enable value (13.0 by default). These are self-explanatory.

    To be honest, with TD04's (especially the billets!!) spool is so fast, this feature probably isn't necessary and might be better off left disabled. I'll play with it on my car for a bit and post results.

    You TD05 and bigger guys though will probably love this feature! It's the next best thing to VVT.
    Last edited by Greg E; 03-23-2012 at 12:32 AM.

    2014 Exomotive Exocet - #101 "shocker yellow" - 1.8L 5-speed 3.9 torsen FMII powered
    Read more: http://mevowners.proboards.com/threa.../greg-pa-build

    99 Solano Black VR4 - #16 of 287 - ground up restoration - sold
    98 Pearl White VR4 #54 of 231 - 12.84@105mph - 93 Octane 12.50@107mph - 100 Octane with Chromed ECU - sold
    99 Pearl White VR4 #108 of 287 - 3RD place stock car class ECG 11 - Sold
    98 Black VR4: 100% stock - totalled by an Illegal 2-12-08
    95 White Stealth TT - 11.852 @ 118.25 - sold
    95 SSG Stealth TT - 11.981 @ 115.81mph - sold

    "I don't actually work on cars, I just talk about them on the internet."

  2. The Following 2 Users Say Thank You to Greg E For This Useful Post:


  3. #2
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Wow neat find! Man the more work you do the more I wish I went back in time as a fly (well invisible human would be better) in the design room for these ECUs.

  4. #3
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Quote Originally Posted by Toni View Post
    Wow neat find! Man the more work you do the more I wish I went back in time as a fly (well invisible human would be better) in the design room for these ECUs.
    Just get me the higher level source code this was written in and I'll reward you very handsomely!!!!

  5. #4
    Banned J. Fast's Avatar
    Join Date
    Sep 2010
    Owner Since
    - O - SIX -

    Location
    Colorado, USA
    Posts
    2,711
    Thanks
    405
    Thanked 200 Times in 140 Posts
    Very old trick, nice to see it can be implemented in a flash. That's how I spool em up. I always get asked about my lean dip at 3500, "you've got a lean spot there ...look at the AFR hump on the logs". Now you know. Pretty cool you can crack code Greg, that's proscribed for me, I can't stare at code all day, not for me.

  6. #5
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Quote Originally Posted by J. Fast View Post
    Very old trick, nice to see it can be implemented in a flash. That's how I spool em up. I always get asked about my lean dip at 3500, "you've got a lean spot there ...look at the AFR hump on the logs". Now you know. Pretty cool you can crack code Greg, that's proscribed for me, I can't stare at code all day, not for me.
    I lost my girl last week because she gave up trying to pry me away from the computer. True story!

  7. #6
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    Alright, I got a question. What would be the difference between doing this and just leaning out a portion of the high octane map? If it is airflow based, it would be the same thing right?

  8. #7
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Your fuel table.is just your base table with numbers in it. If you tuned the fuel table.for lean spool, you're only tuning for the same driving condition. Say foot to the floor in 3rd at 2000 rpms. In order for you to take full advantage of your newly tuned fuel table, you would have to start at 2000rpm in 3rd.

    Let's be honest, in a drag race application, that's not going to work. When you're road coursing, you're constantly changing gears and throttle so that won't do much good either. When you're driving on the streets, your right foot behavior always changes.

    The lean spool code is programmed to know when you're punching it and you tune the timer parameters and intensity of it. It'll do the math for you so that you will get lean spool in any driving conditions any time.

  9. #8
    Forum User verified

    Join Date
    Sep 2010
    Owner Since
    1

    Posts
    1,292
    Thanks
    77
    Thanked 89 Times in 55 Posts
    Can that paralleled to us tuning with piggy backs and having issues with partial throttle, varying rpm etc?

  10. #9
    I lack color... verified

    Join Date
    Sep 2010
    Owner Since
    Aug 1998

    Posts
    3,589
    Thanks
    104
    Thanked 498 Times in 241 Posts
    Quote Originally Posted by Toni View Post
    Can that paralleled to us tuning with piggy backs and having issues with partial throttle, varying rpm etc?
    Nope. The bit to enable this section of code is disabled. Even if it was somehow turned on, the tables the code references are blank. I had to create them then point the code to them in order to get it to work.

  11. #10
    Member
    Join Date
    Sep 2010
    Owner Since

    Location
    Arvada, CO
    Posts
    198
    Thanks
    0
    Thanked 25 Times in 20 Posts
    I know its old but does anybody have any results from using lean spool yet?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
  • History
  • Information
  • Groups
  • Events
  • Resources
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net