I was wondering if anyone has bought/used this catback before. It says 2.5in outside diameter piping but I dont think 2.5in piping would mate to the cat/testpipe that is 3in. Can anybody confirm if its 2.5 or 3in at the cat?
Megan Racing
I was wondering if anyone has bought/used this catback before. It says 2.5in outside diameter piping but I dont think 2.5in piping would mate to the cat/testpipe that is 3in. Can anybody confirm if its 2.5 or 3in at the cat?
Megan Racing
hate to link to the other site but here you go. Ebay Exhaust Review G-Blue Knockoff <-- MUST READ --> - 3000GT/Stealth International Message Center
I personally run it on my car and it just plain souunds mean, has a nice deep growl to it not ricey at all (besides the looks, aka giant fart cans). It's three inches at the cat and then it has a y which goes to 2.5 inches to each side. oh and i know your going to ask, the ebay ones and the megan one are exactly the same they are both made out of California at the same location, they are just sold by different sellers
Last edited by jessecain1; 10-24-2011 at 02:51 PM.
Motor: 3.5 6g74, 3sx lw pulley, Maximal solid mounts, 8.5mm msd wires, Big tyla ground wires
Drive Train: Spec stage 2, Rps lightweight flywheel
Fuel: Ohhnoo ss fuel loop, TT fuel pump, TT fuel pump assembly
Nitrous: Zex Wet EFI Nitrous Kit, zex bottle heater, Zex purge kit, Zex no2 gauge, Nos window switch, Weevil custom ashtray nitrous switch panel
Managment: Autometer A/F gauge, Hand Held Halo dataloger, 3sx in bay fuel pressure gauge
Suspension: Front and rear ultimate performance strut bars, Megan springs, Saleen wheels
Intake/Exhaust: Generic cone filter intake and arm, Ultimate performance intake box, 3sx downpipe, 3sx test pipe, Megan catback
look Good: 3sx plug cover, 3sx engine covers, Polished plenum, Polished valve covers, Polished fuel rails, 3KGT2NV allen bolt ss kit, 2g black garnish, Rear active aero transplant, Jdm snake eyes
Interior: Custom two tone leather, Pioneer dvd, Alpine speakers, Alpine 4way amp, Ultimate performance door sills, Razo shift knob, 3sx Aluminum Pedal Covers, dual piller pod
wasting my money on a NA since 2009

Then link to the one I started here....LOL :http://www.3sgto.org/f13/ebay-exhaus...read-2188.html
For the price you can't beat it. Direct bolt on, 3" at the cat and splits back to 2.5, SS "of some grade" and sounds great!!
I have had mine installed now for almost a year and it still looks great and no rust at all!!! I think I am the first to get it for a 3S and have it installed.
The seller has jacked his prices up, just checked. 395 Buy It Now.
Just FYI,
Funny, he says 2.5 or 3in is good for a 2.0L NA engine but its also just fine for a 3L V6 TT, lol.
Greetings Jerel,
MEASUREMENTS:
- 2.5" OD piping, 4.0" tip, 2.5" ID @ inlet flange
It was for the entire system. Most exhaust systems are the same diameter throughout. Don't be too focused on diameter. Only 3" is needed for a boosted application, often times 2.5" +/- is more than enough for a N/A engine. On my own vehicle, a 1.6L, a 2.25" piping size creates a more usable powerband than a 2 3/8" piping size. On my 2.0L engine, it liked 2.5" but also has the capability to benefit from a 3" even when N/A, but only if you have supporting mods. Does your car have heavy engine work? (Internals)
Last edited by VR-4 0wnz j00; 10-25-2011 at 11:49 PM.
|
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
|
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
|
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
|
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Bookmarks