PDA

View Full Version : clutch issue



Nappien
06-10-2012, 08:09 AM
ok..
i have a issue with my clutch/gearing now..
i was backing out from my garage and when I put it in neutral it kept backing up slow..the gear didnt disengage properly.

I have noticed that I dont get the same pressure when on the cluch pedal as I did before. I checked the fluied, thats still the same.

I have no problem changing gears, but when releasing the clutch pedal I can shift from one gear to another without using the clutch..Im afraid to go out driving and finding myself without the possibility to change gears, or put it in neutral at a stop.

What can I be looking at here? What should I be looking at?

I have a 92 Vr4, with a sinter cluch..

speedy25
06-10-2012, 08:23 AM
You are not getting a full release of the clutch. The most common cause is adjustment of the clutch master cylinder. Next would be a CMC/slave going bad. Least possible but still probable is a broken pressure plate.

-SP

Valhallaz
06-10-2012, 08:56 AM
I'd start by adjusting the clutch pedal play.

Nappien
06-10-2012, 11:47 AM
Ok so I adjusted the free play..found out I did it the wrong way and had to do it over again :P But it did make some difference on the feeling of the cluch. But the gears can still be changed without using the clutch..I havent run the engine or the car after the change, do I have to do make this work?

sometimes I wish I was a mechanic, and knew what I was doing :P

http://i1092.photobucket.com/albums/i405/segmenty/IMG_20120610_155735.jpg

J. Fast
06-10-2012, 01:04 PM
If you pump the clutch pedal does it get stiffer or does it keep the same pressure? Pump it like 10 times consecutively and then recheck the level. The other thing you might check is the counterweight on the transmission and see if it's getting blocked out from intercooler or radiator hoses.

Sin'sVr4
06-10-2012, 01:14 PM
are you changing gears without pressing the clutch with the engine off? Becasue you dont need the clutch with the engine off.

Nappien
06-10-2012, 02:55 PM
I am doing it without the engine running :P I seldom get some time to check anything..with a nagging wife and screaming baby craving my attention all the time :P Will have to continue the checks tomorrow.

Thanks for the replies so far :)

stealthee
06-10-2012, 05:45 PM
Uh, yeah, if the engine is running you don't have to depress the clutch pedal to run through the gears since nothing inside is spinning.

Nappien
06-13-2012, 08:04 AM
jupp..adjusting the free play fixed the problem :)

however..why is the car stalling when shifting from 3rd gear to 2nd..or just slowing down to get into my driveway and having the cluch engaged..bad alternator?

CoreyB
06-13-2012, 09:28 AM
Your IAC has gone bad. Get it fixed soon or it could damage the ECU.

Nappien
06-13-2012, 05:01 PM
is that something i can fix myself, or do i need to order that?
the IAC thats the Air intake controller..or something? im not even sure thats hooked up anymore as there is a open intake on it now..im probably way off here :(

i3igpete
06-13-2012, 05:07 PM
goes into the bottom of your throttle body, 2 bolts.

http://www.stealth316.com/images/isc_loc.jpg

Stealth 316 - ISC Servo Motro (http://www.stealth316.com/2-isc-iac.htm)

stealthee
06-13-2012, 05:51 PM
It might just need cleaned. You can test the resistance. I think there is a test procedure on the page Pete linked.

Nappien
06-13-2012, 07:27 PM
Thanks allot :) I will need to have a look tomorrow..if im allowed :)
I cant keep driving the car when it stalls all over the place..and its not safe when the steering wheel locks up when the car stops :P
Have to see if I find that procedure for testing the resistance.

stealthee
06-13-2012, 07:30 PM
I'll lay it out here for you

123
456

Imagine those are your 6 pins. Check resistance between 1&2, 2&3. 4&5, and 5&6.

You should have 28-32 ohms of resistance in all instances. If not, the IAC is bad.

vroom4
06-13-2012, 07:53 PM
Ive had 3 bad ones that had the correct resistance. :(

i3igpete
06-13-2012, 08:04 PM
Thanks allot :) I will need to have a look tomorrow..if im allowed :)
I cant keep driving the car when it stalls all over the place..and its not safe when the steering wheel locks up when the car stops :P
Have to see if I find that procedure for testing the resistance.

if the steering wheel locks, that makes me believe it's something related to the steering column. even if you have a dead battery, a key in the ignition should still allow you to turn the wheel.

stealthee
06-13-2012, 08:42 PM
I'm going to guess its not actually locking, just getting difficult to turn because the power steering pump is no longer pumping.l

Nappien
06-14-2012, 03:42 AM
Ill try and get it out today and check the resistance, and just order a new one just in case..see you can find one for 40Us on ebay..or ill just order one from DSMISC for 140Us..

What will be the next :S havent really driven the car for 2 years, only a short trip now and then, but still loves it even if my wife is jealous :)

stealthee
06-14-2012, 07:03 AM
You can test it while it is still in the car.

Nappien
06-14-2012, 08:20 AM
did a quick call around for that part here at home..you will not guess what they are expecting..1000$..its so crazy :P

OhioSpyderman
06-14-2012, 08:56 AM
If you find that you DO need an IAC, they can be purchased through RockAuto.com (part is STANDARD MOTOR PRODUCTS Part # AC99) for $68.79.....

They work very well (I have one in my Spyder)....

Bob.

Nappien
06-15-2012, 10:38 AM
I checked the restiance between the pins. Pin 1&2, 2&3, 4&5 and 5&6 looks good with about 30Ohms. However pins 3&4 gives nothing..so im guessing a bad IAC then.
Ill park the car for now, see if I cant order one from RockAuto maybe :)

stealthee
06-15-2012, 05:12 PM
You aren't supposed to get anything from 3 and 4 they are not connected.

Nappien
06-15-2012, 07:28 PM
of course not..it would suprise me if I did it correct the first time :)
so by just measuring the resistance the IAC seems to be good..what is next on the list to check? see if the idle is different without the IAC connected?

Nappien
06-15-2012, 07:31 PM
i ordered a new IAC from rockauto..110$ shipped..allot cheaper than 1000$ they want from a dealer here

Nappien
06-17-2012, 11:46 AM
I removed the IAC and this is what I found

http://i1092.photobucket.com/albums/i405/segmenty/IMG_20120617_155527.jpg

as you can see there is allot of crap in there..so I cleaned it, also the IAC needed cleaning.

http://i1092.photobucket.com/albums/i405/segmenty/IMG_20120617_155513.jpg

So after I get this in the car again Ill need to do a idle speed test, but cant find anything on how to do that..

OhioSpyderman
06-17-2012, 12:04 PM
Yes, that's BAD.

Best way to find out if the IAC is working properly is to start if and let it idle (should be a smooth idle somewhere around 750 RPM's.
Then turn on you A/C. If the IAC is working, it should push the idle speed up to around 1200 RPM's...

You can also do another test when at a normal idle (A/C off) turn the steering to the right and left, the RPM's should jump with each turn of the wheel....

Hope this helps..

Bob.

Nappien
06-17-2012, 01:02 PM
so what if the car wont start after cleaning the IAC and putting it back..what could be the reason? the spring causing the magnetic rotor to jam?
ill disconnect everything tomorrow..dont have the time today :S

Thanks, Bob! If I get the car to start again, ill try and see if the RMP change

Nappien
06-18-2012, 05:32 PM
OK tried to start the car..and what i feared after reading about the IAC..car wont start..no cranking even..
At first the car just died, had to reset the power on the battery. I took everything apart again, adjusted the piston on the IAC, and instead of loosing power I couldnt get the car to start..

I will be away from the car for 5 weeks tomorrow..this will bug me for awhile now :S

OhioSpyderman
06-18-2012, 05:41 PM
When you have time (and it doesn't take long), you might want to pull the ECU and check for damage/leaking capacitors.....

Stealth 316 - ECM Removal (http://stealth316.com/2-ecmremoval.htm)

Bob.

Nappien
08-15-2012, 11:27 AM
Ok..a few weeks later...

I had a chance to change the IAC, and changed the battery connectors and couldnt find any ground faults with the cables.

The car still wont start.

I have a AEM EMS connected so I guess there is no ECM there? I had a look just to make sure, and its not connected to the usual place, so I guess the workshop(bankrupt now) have ECM.
Anybody know what needs to be done? Do I have to get someone to check out the AEM EMS?

J. Fast
08-16-2012, 10:12 AM
Ok..a few weeks later...

I had a chance to change the IAC, and changed the battery connectors and couldnt find any ground faults with the cables.

The car still wont start.

I have a AEM EMS connected so I guess there is no ECM there? I had a look just to make sure, and its not connected to the usual place, so I guess the workshop(bankrupt now) have ECM.
Anybody know what needs to be done? Do I have to get someone to check out the AEM EMS?

Connect to your AEM EMS and use the diagnostic tool that looks like an ambulance.

Add IDLE1, IDLE2, IDLE3, and ILDE4 outputs to the trobleshooting dashboard. IDLE1 is pin 1 for ISC, IDLE2 is pin 3 for ISC, IDLE3 is pin 4. last, IDLE4 is pin 6. You can troubleshoot the stepper motors using the on-board scope.

Also, add MFI relay control output to the dashboard. That would be MAIN RELAY (coil 7) and add the +12v Switched Input

In addition, add coil 1, coil 2, and coil 3

Add GROUND(input), Sensor Ground(output), and Electrical Load which is (switch 3)

The starter signal which is Main Relay (Start sw)

Ignition switch which is Main Relay (Ign sw)

Lastly, add your Airflow input wether it be MAF, MAP, or stock Karmen etc. That will be T4(spare speed).

When you load all those parameters into the troubleshooting dashboard, save the diagnostic dashboard, turn the engine over and see what alarms. Alarms will turn red when the engine is turned over.

To learn how to unlock the parameters and add them to the diagnostic tool ref the manual.