View Full Version : What is involved in going from auto to manual trans?
Gearheadvr4
07-06-2011, 04:21 AM
I've started the conversion but I wanted to make a checklist.
I've gathered up the parts, anything I missed?
shifter assembly, shifter cables, brake and clutch pedal assembly, slave cylinder, master cylinder, lines, starter, passenger axle, drivers side intermediate shaft, starter, flywheel, clutch kit, engine to trans brackets and the trans.
Valhallaz
07-06-2011, 08:59 AM
Other than a shift boot, looks like you have the parts list covered. For me, the hardest part was cutting the hole for the master cyl, but I'm as big as a house with fists the size of softballs. I used a dremel tool and half a dozen cutting wheels, dunno how others did it.
Also, I didn't even attempt a large hole and two small. I just cut the large hole, and then slotted it up and down for the master cyl studs. Works just fine.
n2nsanity
07-06-2011, 11:34 AM
u need the flywheel bolts, they are the same as the flex bolts but a longer
i had some issues with my pass side motor mount bracket, not an issue if it's still attached to the mtx u have
is the trans from the same year as your car? i know 91,92's had smaller axles than the rest, so you could possibly end up needing both axles instead of just the pass side.
if your car is a 93+ be careful not to lose the speedo sensor pin
also, you might want a good bi-metal hole saw kit, use the holes in pedal assembly backplate for a template
and be ready to splice some wires
also, should this be in the drivetrain section?
Gearheadvr4
07-06-2011, 12:09 PM
All the parts are from a 99 vr4 with extremely low miles. Is the pedal assembly is one whole piece or just the backplate? What wires need spliced? I should be ok on the mounts since I have solids from my vr4. I'm doing this in conjunction with my awd conversion too. Will I need to swap over the rotors from the vr4 too or can I keep most of the SL parts? I have slotted rotors and newer front subframe parts. The steering and feel of my SL is very tight. My VR4 wasn't so much...
I didn't even know we had a drivetrain section. If this needs moved, that's ok with me.
Valhallaz - When you say slotted the holes, did you take a pic of this? Not sure I can picture what you mean there.
i've always thought it was a bad idea to attempt multiple mods simultaneously--especially massive ones like you're planning. it's not impossible to do, but troubleshooting any problems becomes exponentially more difficult.
you can keep all of the front drivetrain components from the SL in place; the only thing it impacts is how you go about replacing front wheel bearings & you'll have to use FWD bbk's--if you upgrade.
AudibleSilence
07-06-2011, 01:30 PM
I'd rather be a turbo fwd auto than a fwd manual.
I'd rather be a turbo fwd auto than a fwd manual.
+eleventy billion
TwIzTeD_3kGt
07-06-2011, 01:56 PM
All the parts are from a 99 vr4 with extremely low miles. Is the pedal assembly is one whole piece or just the backplate? What wires need spliced? I should be ok on the mounts since I have solids from my vr4. I'm doing this in conjunction with my awd conversion too. Will I need to swap over the rotors from the vr4 too or can I keep most of the SL parts? I have slotted rotors and newer front subframe parts. The steering and feel of my SL is very tight. My VR4 wasn't so much...
I didn't even know we had a drivetrain section. If this needs moved, that's ok with me.
Valhallaz - When you say slotted the holes, did you take a pic of this? Not sure I can picture what you mean there.
The pedal assembly is one piece...4 nuts on the firewall and 2 bolts that go through the top of it iirc. Don't have to remove anything extra to get it out (other than the plug/rod/spring connected to the brake pedal). Motor mounts shouldn't be a problem. Not sure of the year you're working with, but if it's the same plug as a '94 there will be 3 rows of terminals on the old ATX plug. The middle row should have 4 terminals, the first 2 are for park/neutral switch and the other 2 for reverse lights. The park/neutral you can just splice together to start the car. The reverse you need to splice in the connector that plugs into the trans.
Valhallaz
07-06-2011, 02:00 PM
Valhallaz - When you say slotted the holes, did you take a pic of this? Not sure I can picture what you mean there.
I didn't get pics, sorry.
I mean that I had no drill capable of getting to where the holes for the studs on the master cyl would go through. So instead of drilling holes for them, I cut the initial large round hole, and then cut slots up and down from that that just long enough that the studs would fit into them.
It would look sort of like saturn being the hole, and the rings from the side being the slots.
It would look sort of like saturn being the hole, and the rings from the side being the slots.
Excellent representation - very descriptive.
AudibleSilence
07-06-2011, 03:08 PM
+eleventy billion
Well it's true. What's the point in going through all of that hassle just to say you row gears if you're still slow?
n2nsanity
07-06-2011, 03:21 PM
i've always thought it was a bad idea to attempt multiple mods simultaneously--especially massive ones like you're planning. it's not impossible to do, but troubleshooting any problems becomes exponentially more difficult.
you can keep all of the front drivetrain components from the SL in place; the only thing it impacts is how you go about replacing front wheel bearings & you'll have to use FWD bbk's--if you upgrade.
+1 on this
Do it in steps
I'd start with 1st step being the holes on firewall as most say this is the most tedious
An angle headed drill adapter would be very helpful.
http://www.harborfreight.com/media/catalog/product/cache/1/image/370x/9df78eab33525d08d6e5fb8d27136e95/i/m/image_2456.jpg
My hole saw kit was only meant for wood, so it sucked. Bi-metal hole saw kit is what you need.
I ended up using stepless bits, which cut though like butter. Step bits should work too. I think the small holes are 3/8" and the big hole is 1 3/8". Measure it to be sure.
These will work just as good as the bi-metal hole saws if not better and will be cheaper, but just make sure you have the right sizes.
http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_1812.jpg
Also, I'd recommend the single braided ss clutch line setup. Makes installation much easier, better pressure and it's only like $30 i think.
n2nsanity
07-06-2011, 03:30 PM
Well it's true. What's the point in going through all of that hassle just to say you row gears if you're still slow?
+1 on this too
Too late if you already bought the parts, but in many cases it's about the same cost to do a tt conversion on your atx
If they were free, then you can't beat that. But then again, it's still not too late to sell them and put the $ towards a tt conversion :)
Mine wouldve been free from leftover parts from other cars except for the new parts i opted to replace
I think I spent like $350ish on new flywheel, clutch kit, axles and braided ss line
Gearheadvr4
07-06-2011, 05:03 PM
I must have forgot to mention that I'm converting from an SL to a TT AWD... I believe have every part I need from a donor plus I have a parts vr4 completely intact.
AudibleSilence
07-06-2011, 05:31 PM
Good Luck. When you get to the shit tons of pumps and other things where the rear end should be let me know. Conversion on a Spyder = PITA.
good luck. this is probably the most massive undertaking anyone has ever tried on a 3/s; targa tops included. i think even vr440's massive undertaking might be a bit easier. i'd love to see it done...i just think you're totally barking up the wrong tree. think about it:
mtx conversion
awd conversion
tt conversion
you should sell it and buy a spyder vr4. seriously. i'm not even joking. the time, effort and ass pain JUST TO GET TO STOCK SPYDER VR4 is incredible. and you haven't even had this car that long--unlike paul or i, who've owned our cars for well over 5 years before going with AWD conversion insanity.
n2nsanity
07-06-2011, 08:03 PM
if you really want to do all the extra work, i think you can handle it
you've got plenty of extra parts
just don't expect to finish over a weekend or anything
take it 1 step at a time and you'll do fine
but, like ipd is saying, it might actually save you a lot of time and maybe even some $ if you sell your spyder sl and buy a spyder vr4
you'd be able to sell you're extra parts and if your vr4 is a parts car because its totaled, even after you've removed everything useful or valuable from it, the shell is still worth like $300 in weight to scrap it
Alex3000gt
07-06-2011, 10:10 PM
Why did your NG registration say you were an AWD converted Spyder?
AudibleSilence
07-06-2011, 10:13 PM
Why did your NG registration say you were an AWD converted Spyder?
Cause he registered before realizing how much harder the conversion is on a Spyder and didn't get it done in time? Just a guess.
Alex3000gt
07-06-2011, 10:28 PM
Cause he registered before realizing how much harder the conversion is on a Spyder and didn't get it done in time? Just a guess.
Based on his registration number he registered in the two weeks leading up to the event. That is very ambitious.
Gearheadvr4
07-07-2011, 03:01 AM
Partially true. I started my registration months ago but didn't pay until a few weeks prior. Had to be sure I could get the time off work. Some of the info was old and wishful thinking. It came to a point of taking a chance of not making NG or going with an untested setup and driving nearly 24hrs barely tuned and unsure. I came up with option C and hastily put everything back to mostly stock. I was able to at least finish the full black interior swap minus the leather seats.
I hope I know what I'm getting into here. I've owned a bunch of VR4s and Stealths over the years and Supras before that. I have the skills but I am worried about not driving my Spyder for 2 months during the process.
i think all of us are less worried about it being down for two months than we are about it being KIA.
Gearheadvr4
07-07-2011, 08:58 AM
Ouch, if I didn't know 100% that I could do it, I wouldn't even try. Nobody loves this Spyder more that me.
I agree with you guys though. If I could even find a VR4 Spyder at decent price I'd just buy that. A lot easier. I picked up this one at an extremely good price and everything works. It was pretty much stock besides the slotted rotors. After I convert the SL it will still be much cheaper than I could hope to find in a VR4 Spyder.
i have high hopes, and i freely admit that i'm a jaded cynic.
and no, i don't think you'll come out ahead. the time/effort invested would easily buy you a spyder vr4 if you had a secondary job. i've seen several selling for under 20k within the last year.
AudibleSilence
07-07-2011, 10:23 AM
You're going to hack up the car. You are going to spend more than had you just sold it for 10-15k and added a few grand to get a Spyder VR4. I hate to sound negative, but you are not the first to have this idea..just the first to waste time trying.
I'm just waiting for you to brick the roof by cutting a hydraulic line on accident. It's honestly a lot more difficult than you seem to grasp.
Jimvr4
07-08-2011, 03:05 PM
I'm not going to doubt that this can be done but in the end what will you have? It can never be sold as either a VR4 Spyder or an SL Spyder. I would either keep it for what it is or sell it and save up for the VR4 Spyder you really want.
I'm not going to doubt that this can be done but in the end what will you have? It can never be sold as either a VR4 Spyder or an SL Spyder. I would either keep it for what it is or sell it and save up for the VR4 Spyder you really want.
worse...try insuring it. believe me, i know what i'm talking about.
Hans@GZP
07-08-2011, 04:50 PM
We've never had an issue insuring any of our swapped cars for what we thought they were worth.
We had Em's rebuilt title spyder sl insured for $30k before.
must just be PA. trying to get insurance down in GA for my car is a nightmare of biblical proportions. i doubt even with a professional appraisement i'll be able to get it sufficiently insured.
Gearheadvr4
07-08-2011, 05:51 PM
That's definitely true. But I'd never want to sell it. After all this I could never bring myself to let it go. Like I said, I've put a lot of effort into her already.
Emilie@GZP
07-08-2011, 06:01 PM
must just be PA. trying to get insurance down in GA for my car is a nightmare of biblical proportions. i doubt even with a professional appraisement i'll be able to get it sufficiently insured.
you just need receipts, that's all the require. Need to be able to show the cost of the aftermarket parts/work done to justify the price of the vehicle. Progressive Insurance, it's nothing state specific.
no reciepts for work done--especially if you do it yourself. i mean, just how many shop hours is an AWD TT MTX conversion worth? how do you bill that?
hell, 99% of my parts have paypal receipts--not itemized shop reciepts. and the only thing on a paypal receipt denoting parts is whatever i threw in the comments section of the transaction. hardly "proof positive".
Emilie@GZP
07-08-2011, 06:11 PM
You bill it for how long it takes.....
TwIzTeD_3kGt
07-08-2011, 06:39 PM
+1 for stepped drill bits to make the firewall holes. I make 3 holes when I do it. Just mount the pedal assembly, make an outline of the holes. Dismount pedals and drill baby drill.
Gearheadvr4
07-08-2011, 11:12 PM
Can it be done with the dash in? I'm guessing there's not enough room. Really hate to pull it, I just put it back in.
TwIzTeD_3kGt
07-09-2011, 01:03 AM
yeah you don't have to remove anything. don't need to use a right angle drill either.
Alex3000gt
07-09-2011, 01:44 AM
Done this twice, and both times drilled from the fire wall. Used a punch to mark the center hole from my template, and one of tnose drill bits with a metal cutting cylinder around it with the proper size diameter. Not the most effective way, but cheap and gets the job done.
Done this twice, and both times drilled from the fire wall. Used a punch to mark the center hole from my template, and one of tnose drill bits with a metal cutting cylinder around it with the proper size diameter. Not the most effective way, but cheap and gets the job done.
what's the most effective way? screwdriver, hammer, and some vodka? :suspect:
Gearheadvr4
07-09-2011, 06:38 AM
Ok, I have a pretty good handle on the front subframe, shift cables, trans, and now the pedals. What about electrical differences? Reverse light, clutch lockout, ect.
Also If I wanted to transfer the auto trans from the Spyder to another NA manual would I have to swap the whole engine harness or could it be spliced in? I'm guessing the ECU has a pinout to the auto computer for speed or RPM?
Ok, I have a pretty good handle on the front subframe, shift cables, trans, and now the pedals. What about electrical differences? Reverse light, clutch lockout, ect.
Also If I wanted to transfer the auto trans from the Spyder to another NA manual would I have to swap the whole engine harness or could it be spliced in? I'm guessing the ECU has a pinout to the auto computer for speed or RPM?
fairly certain that it can be spliced in. as you noted, TCU has only a few inputs it needs from the ECU.
mtx >atx is a mod i've always wanted to see done. and (god forbid) if some how my car ends up totaled, it will be the very first thing i'll do with whatever 2g tt i replace it with.
Emilie@GZP
07-09-2011, 09:31 AM
We are doing a 95tt atx awd swap right now at the shop.
Gearheadvr4
07-09-2011, 05:19 PM
I wish I could see the progress. Any way you could help me out with some of the more challenging things that come up?
Also on a side note, I still need a couple parts for the Spyder. OK to PM you with a parts request?
n2nsanity
07-09-2011, 05:20 PM
if you were considering using the old atx in another car, i'd go ahead and pull the engine harness, ecu, tcu
no splicing needed and may be easier in your scenario
i know many will disagree with me on this, but i found it easier to pull the engine/atx out together and then swap it
i had so much trouble just removing the atx, i couldn't imagine trying to get it back in with the engine still in
mtx is much smaller, and isn't bad to remove or install with the engine already in
i prefer to deal with the fuel lines, radiator hoses and few wires than to cram an atx back in anyday
i still think it'd be much less of a pita to buy spyder vr4 or just tt this thing
not saying you can't do the work
i've done most of this already, and i'm no mechanic or anything. but this a spyder, so it's going to be a bit more challenging than my swaps were
Hans@GZP
07-09-2011, 06:33 PM
Go ahead and shoot Emilie a PM with what you need or any questions and we'll do what we can to get back to you quickly.
We are doing a 95tt atx awd swap right now at the shop.
a fwd atx > awd atx tt swap; or an rt/tt > atx swap?
p.s.
n2nsanity, although i've not done it myself, i think my preference would be to use the tt harness & splice into it. i'd rather be able to run a resistor pack; rather than have a rat's nest of wiring at the injectors.
Hans@GZP
07-09-2011, 08:18 PM
It's an RT TT that we're converting to auto. We've already done the FWD to AWD ATX TT swap a couple of times... even a FWD to AWD ATX NA.
It's an RT TT that we're converting to auto. We've already done the FWD to AWD ATX TT swap a couple of times... even a FWD to AWD ATX NA.
yeah, that was mike's.
post up a build thread on it. i'd love to see it. should be full of useful info--as i don't recall anyone ever attempting it previously.
Hans@GZP
07-09-2011, 08:31 PM
Well, technically we bought it from Mike before the swap was done and then sold it. The kid that bought it has no idea that he's probably the only one in the US with a car like that.
AudibleSilence
07-09-2011, 08:54 PM
It's an RT TT that we're converting to auto. We've already done the FWD to AWD ATX TT swap a couple of times... even a FWD to AWD ATX NA.
That was mine :D Fuck that deal...I never wanna live through that sale again.
Well, technically we bought it from Mike before the swap was done because it was supposed to have been done looong before that and it wasn't because I had a Mexican't working for me that went missing for a week. It caused both me and Mike a shit ton of grief...but Mike should have been smart enough to know to not take a shop's word on an eta and sell a car before the work is completed. Mike had to deal with a fucking psycho as a result, and I helped him out by buying the car from him.
Fixed. I do still have the pictures though. And no I'm honestly not bitter, I learned a shit ton in my dealings with that car..like never do business with a friend.....ever. And never ever count your chickens before they hatch. Hans really did come through in the end, he saved me much more grief than I would have had otherwise, even though I was 100% accommodating to that pos that originally wanted that car.
I'm glad it's gone, that car almost killed me...twice. I just feel bad that Hans had to spend so much time and money fixing another person's mechanical fuckups.
That was mine :D Fuck that deal...I never wanna live through that sale again.
Fixed. I do still have the pictures though. And no I'm honestly not bitter, I learned a shit ton in my dealings with that car..like never do business with a friend.....ever. And never ever count your chickens before they hatch. Hans really did come through in the end, he saved me much more grief than I would have had otherwise, even though I was 100% accommodating to that pos that originally wanted that car.
I'm glad it's gone, that car almost killed me...twice. I just feel bad that Hans had to spend so much time and money fixing another person's mechanical fuckups.
wait....so GZP had a good-for-nothing brit AND a good-for-nothing mexican working for them...at different times? wow! now all they need is a good-for-nothing vietnamese and it'll complete the trifecta of suck.
Hans@GZP
07-09-2011, 09:37 PM
That car/deal was such a cluster f*ck haha. I'm so glad it's over. Some Vietnamese guy ended up buying it :p
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.