PDA

View Full Version : finally got to run her at the track fri!!



Sin'sVr4
05-16-2011, 04:54 PM
i ran pretty consistent all night. first run i ran a 12.1 @121-1.82 60ft. Then pretty much 12.2-12.3 rest of the night. got real cold and my hard street tires suck. was in the 1.85's 60ft all night. just need to figure the launch out better. i think in the vid i ran a 12.2 in that one. i was bump reving and built boost to around 7-10 psi. pretty good, spun a bunch coming out. friggin start area sucks bad. i need to get some drags or slicks. ugh..

vid is post #40

http://www.coloradohpjunkies.com/for...-13-2011/page8

mb3000
05-16-2011, 07:22 PM
Page not found.

Amphiron
05-16-2011, 07:40 PM
http://www.youtube.com/watch?v=luFG3ZtzNTQ&feature=player_embedded
http://www.coloradohpjunkies.com/forums/showthread.php?2452-pmp-first-fri-night-05-13-2011/page3

green-lantern
05-16-2011, 07:53 PM
Very cool man!

Sin'sVr4
05-16-2011, 09:36 PM
dont forget im at 4700ft. :(

Broomfield Racing
05-16-2011, 09:43 PM
Nice job! 121 trap is nice.

11secondFWD
05-16-2011, 11:55 PM
121 is pretty good, but I would think at 121 you would be better. You need to get the 60ft down. On streets, I still can cut a 1.6 flat in almost any awd mitsu car I have driven (auto or manual). Also, my FWDTT ran 11's at that trap speed with a 1.85 60ft, so I think you should be able to beat that 60ft you got even on streets with some practice. But good runs overall and for the elevation.

J. Fast
05-17-2011, 12:30 AM
That's a very respectable time Mike. We lose about half a second here at altitude. And the DA had the track conditions at 6400ft above sea level when you made that pass :) . Get rid of those pig heavy seats and lay off the sodipop for a couple of weeks :lo5l:

Sin'sVr4
05-17-2011, 10:30 AM
thx J. lol im workin on the diet ;). But 11secfwd dont forget im high up in elevation too so it kills us that are not at sealevel. ill hit 11's next time out

UTRacerX9
05-17-2011, 12:43 PM
Well... I don't think 12.1 is a good time for your mods, regardless of elevation sapping power somewhat. Your sig says you have 19T's and E85, with 492awhp. That number ought to be a lot higher, especially considering that VR3.9 just got 500awhp with 13T's and E85. Granted, he's pretty much at sea level, but a well tuned car with 19T's should have about 100 hp more than a 13T car. I see you've got an AEM, so your tune should be much better than what VR3.9 is able to accomplish with his piggybacks and no timing control.

Sin'sVr4
05-17-2011, 01:33 PM
Well... I don't think 12.1 is a good time for your mods, regardless of elevation sapping power somewhat. Your sig says you have 19T's and E85, with 492awhp. That number ought to be a lot higher, especially considering that VR3.9 just got 500awhp with 13T's and E85. Granted, he's pretty much at sea level, but a well tuned car with 19T's should have about 100 hp more than a 13T car. I see you've got an AEM, so your tune should be much better than what VR3.9 is able to accomplish with his piggybacks and no timing control.

really? do you know anything about being at this elevation. i'd be low 11's at sea level and ive never heard of a 13T car hitting 500 Whp. either way, what do you run?

UTRacerX9
05-17-2011, 03:43 PM
really? do you know anything about being at this elevation. i'd be low 11's at sea level and ive never heard of a 13T car hitting 500 Whp. either way, what do you run?

:rolleyes3:

Uh, yeah, I'd say I know a bit. The previous 13T awhp record was 472-475ish for years, and that was on race gas. The new record is 501 with E85. If you have a problem with my post, perhaps you should do a bit of research on what 13T's are running. Your lack of knowledge regarding them isn't helping your case.

As far as your run goes, NHRA uses a correction factor of .9419 for an altitude of 4700ft. Multiplying that with your 12.1, we get 11.39. By 12.3, we get 11.58.

Those are numbers that a well tuned 15G/DR650/13T class car can achieve, and have, repeatedly. Your 19T's should be running faster, and your horsepower numbers should be higher for your mods. Instead of getting all defensive, perhaps you should check for boost leaks and tweak your tune.

EDIT: Not to mention, I'm actually giving you a lower corrected time here, because the altitude correction factor is even less when it is a FI car vs an NA.

vr3.9
05-17-2011, 05:00 PM
I noticed your running 780 PTE's. That the same thing I'm running. Do you have your base pressure turned up? I ran out fuel at 471awhp and then turned it up to 55psi. Anyways, congrats on the run. So close to getting in the 11's. With those traps you can get there no problem.

j2k4
05-17-2011, 05:02 PM
really? do you know anything about being at this elevation. i'd be low 11's at sea level and ive never heard of a 13T car hitting 500 Whp. either way, what do you run?


:rolleyes3:

Uh, yeah, I'd say I know a bit. The previous 13T awhp record was 472-475ish for years, and that was on race gas. The new record is 501 with E85. If you have a problem with my post, perhaps you should do a bit of research on what 13T's are running. Your lack of knowledge regarding them isn't helping your case.

As far as your run goes, NHRA uses a correction factor of .9419 for an altitude of 4700ft. Multiplying that with your 12.1, we get 11.39. By 12.3, we get 11.58.

Those are numbers that a well tuned 15G/DR650/13T class car can achieve, and have, repeatedly. Your 19T's should be running faster, and your horsepower numbers should be higher for your mods. Instead of getting all defensive, perhaps you should check for boost leaks and tweak your tune.

EDIT: Not to mention, I'm actually giving you a lower corrected time here, because the altitude correction factor is even less when it is a FI car vs an NA.

Not minding what you've chosen to post, he's asked you a question, and you haven't answered it, I don't think, because you were busy being superior.

Small oversight, but still - and aren't you running 13Ts?

j2k4
05-17-2011, 05:05 PM
Btw-

NICE RUN, Sin.

UTRacerX9
05-17-2011, 06:21 PM
Hmm. It appears the blind partisan hack on our forum has wandered into a section he is unfamiliar with. Can anyone lend him a seeing eye dog?

Chris@Rvengeperformance
05-17-2011, 09:42 PM
I'd be really happy with that trap speed. The 1/8th mile MPH does seem low compared to the 1/4 for some reason. I hit 89.73 in the 1/8th last year on 13Ts and 93 octane, but my 1/4 trap speed was a lot lower.

Congrats1

Sin'sVr4
05-17-2011, 10:22 PM
thx guys for the boost of confidence.

ok here's my night breakdown..

about 70 degrees starting...

Run#1
60ft-1.825
330-5.117
1/8-7.912
mph-90.18
1000-10.228
1/4-12.140
mph-121.59

Run#2
60ft-1.886
330-5.280
1/8-8.076
mph-89.26
1000-10.404
1/4-12.318
mph-120.04

Run#3
60ft-1.852
330-5.217
1/8-8.025
mph-89.32
1000-10.347
1/4-12.268
mph-118.30

Run#4(flooded out of 1st gear so shut it down)
60ft-1.958
330-6.031
1/8-10.457
mph-49.97
1000-14.033
1/4-17.128
mph-70.13

Run#5
60ft-1.941
330-5.341
1/8-8.166
mph-89.00
1000-10.484
1/4-12.467
mph-114.39(shifted to 4th gear)

Run#6
60ft-1.894
330-5.343
1/8-8.134
mph-90.20
1000-10.440
1/4-12.340
mph-120.54

The last 3 runs it was freezing out, probably low 40's, and the track sucked balls. no one could hook all night. The car would hesitate when i would shift to 2nd at first then take off hard...not sure why. i have my fuel cut set to 6500, im gonna up it. not sure why it would hesitate. didnt do it on the first run, but did it on every single other run. wierd. Anyone know why it was doing that?

HellBringer
05-17-2011, 10:37 PM
If you're rev-limiter/fuel cut is really set to 6500 then that is your issue right there and explains a lot! Up the limiter to 7500RPM and try shifting at 7000-7200 and you'll go mid 11's at probably a little closer to 125MPH all day long. The car is really moving out on the big end and short shifting 1 and 2 is the reason for the low 1/8 relative to the 1/4 MPH.

J. Fast
05-17-2011, 10:50 PM
Hey, you're leaving out the best part Mike. Your average reaction time was .6 of a second. There's room for improvement there too!

Sin'sVr4
05-18-2011, 12:32 AM
r/t#1 .423
r/t#2 .313
r/t#3 .181
r/t#4 .556
r/t#5 .554
r/t#6 .282

avg = .384 :)

my fuel cut was set to 7000. i upped it to 7500. i was shifting right around 6700-6800rpms. now i will push it a bit farther. my plugs are gapped at .22, maybe ill try some different plugs. mine are coppers and about 500 miles on em. wonder if i can gap em smaller?

Sin'sVr4
05-18-2011, 01:00 AM
http://i62.photobucket.com/albums/h116/mikepeterson/nada.jpg

Here is my dyno sheet. Based off this, what is my shift points i should be hitting?

11secondFWD
05-18-2011, 01:38 AM
Elevation I agree is hurting but the short end seems slow. The 60ft is not great and the eighth seems slow too. But you pick up a good amount in the top end (30mph) which is great. You just need practice with the first half of the track and some traction and better launching. I would shift at where you are or maybe a little higher. 6800 is pretty far for the small turbos but 7k might help some. The graph doesnt go very high but it doesnt look like the power is dropping much yet in the graph.

11secondFWD
05-18-2011, 01:39 AM
Hey, you're leaving out the best part Mike. Your average reaction time was .6 of a second. There's room for improvement there too!

Just making sure, you do know that reaction time doesnt change the 1/4 mile time, correct?

J. Fast
05-18-2011, 01:55 AM
Haha. I just bust Mike's chops about being asleep at the wheel and a being a bad driver. He's not really either, it's just a running joke in our local chapter cause every time he used to drive it he broke something from driver error. He gets all defensive and it makes for good chukkles.

J. Fast
05-18-2011, 02:49 AM
http://i62.photobucket.com/albums/h116/mikepeterson/nada.jpg

Here is my dyno sheet. Based off this, what is my shift points i should be hitting?

If you're using your dyno sheet the limit has not been defined yet. You are not losing peak hp on the dyno chart, at all. With the dyno sheet method one of the ways to determine a shift point is to take the HP curve as far out as you can while maintaining safe and comfortable limits of engine operation. In most cases the dyno chart will bell curve out like the shape of your torque curve. Once you get that you find a shift RPM which brings you back to the same point on the horsepower curve where you shifted from (ie. you leave 2nd gear at 7500rpm/450hp and you pick up 3rd gear at 4500rpm/450hp). So in a perfect world using the dyno sheet method your gearshift would be evenly split on the curve so that you maintain the maximum area under the horsepower curve.

For example, let's say your torque curve in the graph represented a hp curve. Now extend it to 7500 rpm and hold 500hp. You know that when you shift you're going to lose roughly 3000rpm. In a round about way when you shift at 7500rpm you pickup your net gear at 4500rpm. You integrate (or take the area under the curve) from 4500-7500 and say you get an average of 465hp.

Now lets say you shift at 6000rpm whereby you drop down to 3000rpm. You integrate from 3000-6000 and say you get an average of 420hp. Hence, it could be said your average hp is higher if you shift later.

In a nut shell if you wanted to make an excell sheet and start at 100 rpm increments starting at 2000rpm and mark down your hp number for that column, you could eventually find the highest mathmatical hp combination between subsequent gearshifts and that would be your optimum shift point.

Right now your optimum gearshift is going to be redline because you're still developing/holding peak power at the dyno cutoff. You have no bell curve. Your peak hp line is relitively flat from 4500 rpm to 6000rpm.

familyMAN
05-18-2011, 03:21 PM
I asked in your dyno thread also...still don't understand why your dyno stops at 6k rpms? As J.Fast stated, hard to say where you shift points should be because you don't know what your holding to redline. Since you have AEM, you should try the virtual dyno software Trevor posted about and do a pull to see what your full curve looks like.

Sin'sVr4
05-18-2011, 03:25 PM
hmm i will once i get it back together. been doing alot of weight reduction stuff so ill try that.

familyMAN
05-18-2011, 03:28 PM
Did you get an HKS DLI? With that you should be able to open up your plug gap and up the boost:)

Also, can't tell from your sig, but are you only using one walbro?

Sin'sVr4
05-18-2011, 03:33 PM
havent got the hks dli yet. yes one walbro still

familyMAN
05-18-2011, 03:44 PM
havent got the hks dli yet. yes one walbro still

If you are still running 55psi base fuel (stated in your dyno thread), that one walbro is beyond maxed at 20psi of boost for 500awhp on E85. Time for a second pump.

UTRacerX9
05-18-2011, 03:45 PM
One walbro, with 780cc inj. You're running out of fuel, plain and simple. At 20psi, even if your pump was getting 16.5 volts to it, (and I don't see a boostapump in your sig) you would be at the absolute limit of your injectors, and that's at 43 base fuel pressure. If you're at 13.5 (which is all a hotwire kit will give you) you require far more fuel than your pump can put out at that voltage.

Beat me to it.

familyMAN
05-18-2011, 03:50 PM
:stupid:


Good trap speed though!