View Full Version : Finally, a new 13T World Record. Details inside
vr3.9
05-07-2011, 11:50 PM
Decided today was as good as any to use my free hour of tuning I won at Texas Gathering. No hype no crowds just me and 3 other guys counting Steve, the dyno owner.
I tried to beat the record 472awhp at the TX2k11. Got 471 running out of injectors on following pulls. So I turned fuel pressure up 55 and retuned.
1st pull - 493awhp @ 19psi
http://www.youtube.com/watch?v=yfVRxQZAEJM
http://i225.photobucket.com/albums/dd64/reachmercer/Picture005.jpg
Tried turning up the boost hit about 24 after about 5600rpm just fell apart.
Next pull 491 still going a little nuts past 5600rpm.
Let it cool for about 15 minutes and turned the boost down a little.
4th pull 501awhp @ 21psi. It still wanted to fall apart at 5600 again but made it through it. Unfortunately my camera man must have got too excited and turned it off before he went to the screen, but I got a dyno sheet and 3 witnesses. :D
http://www.youtube.com/watch?v=83jxm6uXa_g&feature=channel_video_title
http://i225.photobucket.com/albums/dd64/reachmercer/Picture006.jpg
RealMcCoy
05-08-2011, 12:05 AM
Congradulations, pretty stout numbers there. Pretty much exactly what you set out to do... Looks like it might have a little more in it if you can solve the issue limiting you to 21 lbs.
vr3.9
05-08-2011, 12:10 AM
if you can solve the issue limiting you to 21 lbs.
yea the turbos seem to hit 24 with no problem, but i think I would have to do it on my first pull. I actually want to see if this happens to other people with crx racing front mounts. I've noticed a similar eratic, up and down wave on one other with a crx front mout. Probably not an issue when your driving because you get so much air, but I think it gets heat soaked pretty quick on a dyno. Would like more info on that before I make a conclusion.
mb3000
05-08-2011, 12:33 AM
Congradulations! I know you've been after this for a while now, glad to see it finally come together.
vr3.9
05-08-2011, 12:46 AM
premium gas (93)? meth?
Now that would be something. Pump gas..... yellow pump. E85
Oyyci
05-08-2011, 12:52 AM
Congratz man! That thing sounds good!
GTOJOE
05-08-2011, 12:56 AM
Nice work. What fuel are you running?
Edit: didn't refresh before posting... question already answered hahaha.
FeaRpb
05-08-2011, 01:00 AM
Nice Mike
GTO Assassin
05-08-2011, 01:23 AM
Since when did Stone Cold Steve start tuning 3/S's? :eek:
Scoot
DuTTch
05-08-2011, 02:06 AM
Congrats Mikey
Hym3n
05-08-2011, 02:14 AM
Very nice!! All this just from bumping that fuel pressure up a bit. It does sound like heatsoak is your cause for problems. That, and its kinda hot here. IIRC, CANEAC's run was in February/March, meaning much lower temps. Enjoy it as it sits for now!
Mod list at time of dyno? (can't remember if you left off the rear aftermarket manifold/o2) Any block/head work?
vr3.9
05-08-2011, 02:27 AM
Very nice!! All this just from bumping that fuel pressure up a bit. It does sound like heatsoak is your cause for problems. That, and its kinda hot here. IIRC, CANEAC's run was in February/March, meaning much lower temps. Enjoy it as it sits for now!
Mod list at time of dyno? (can't remember if you left off the rear aftermarket manifold/o2) Any block/head work?
Yea, fuel pressure was the big key. Probably still the key to tweaking out any last few horses. Probably need to turn it down just a smidge. Updated my sig. I had to finally give up on that rear header after it cracked for the 4th or 5th time and lost me the trophy at the Texas gathering. Block and heads are just as they were on that 92 GTO clip.
Ok before anyone asks. I got lucky that 92 GTO clip had a forged crank and 25 spline tranny/tc.
AdamVR4
05-08-2011, 11:36 AM
Daaammnn! Congrats!
It hasn't been said so unless I'm missing something, I'll point out the obvious... The increased fuel pressure resulted in lower IDC's and therefore more ignition timing.
Depending on where your timing is, you can potentially get more power with more 'fuel pressure' (not less)... But the better way to do this is to get something like an emanage with timing control.
Either way, sweet numbers! Really similar to what adrenaline_vr4 made at the TX Gathering in 2004 on 18T's @ 20 psi on a Dynojet. What turbine are you using? Stock heads?
green-lantern
05-08-2011, 12:29 PM
Awesome Mike! You going to NG this year?
thor'svr4
05-08-2011, 12:48 PM
nice numbers!!!!!!! congrats on breaking the 500 mark!
vr3.9
05-08-2011, 03:16 PM
Daaammnn! Congrats!
It hasn't been said so unless I'm missing something, I'll point out the obvious... The increased fuel pressure resulted in lower IDC's and therefore more ignition timing.
Depending on where your timing is, you can potentially get more power with more 'fuel pressure' (not less)... But the better way to do this is to get something like an emanage with timing control.
Either way, sweet numbers! Really similar to what adrenaline_vr4 made at the TX Gathering in 2004 on 18T's @ 20 psi on a Dynojet. What turbine are you using? Stock heads?
Since I can't do much about timing but change fuel pressure, I've never really looked into optimum timing, I know at some point it won't make any more difference and then will make less. Right now its running about 34 degrees. Scott wasn't making any more power after 26 so I don't know. I can either barely turn up fuel pressure to get my afr's down to 12.1 or turn it down just a bit and drop back the tune 1 click. At the pressure my choices were 12.4 or 11.7. The biggest problem I think is heat soak on the IC. After the first pull things to break up a bit. Would like to see if it would hold more boost, but turning it up after got hot just made it break up worse.
vr3.9
05-08-2011, 03:19 PM
Awesome Mike! You going to NG this year?
I know it's going to be a good time but don't think I'm going to make it this year. But, who knows that could change. Sorry for the double post thingy just found the multi quote button.
green-lantern
05-08-2011, 03:37 PM
I know it's going to be a good time but don't think I'm going to make it this year. But, who knows that could change. Sorry for the double post thingy just found the multi quote button.
:( ahh shit, is anybody from the TX crew coming this year?
vr3.9
05-08-2011, 06:13 PM
I know GTwizard is. I think there might be a few others, just not sure. Not sure about showkiller. We need to start getting some of our local meets going again before the Texas crew fades out.
I'd expect "tork" be over 500 with e85...
vr3.9
05-09-2011, 03:18 PM
I'd expect "tork" be over 500 with e85...
Me too! I was pretty sure tq would hit 500 before hp. In the past I've always made more tq than hp. I guess at some point tq just gets harder to make cause it still made more than I have before.
Congrats, Mike.
By golly, you said you'd do it, too.:)
so my hopes and dreams hitting at least 500 awtq (on 13Ts and e85) were just ruined by this thread....
vr3.9
05-09-2011, 04:18 PM
so my hopes and dreams hitting at least 500 awtq (on 13Ts and e85) were just ruined by this thread....
This is correct. It is impossible. Do not attempt. It is a complete waste of time.:BangHead:
For the love of all that is good..... don't go out and break my record. :lo5l:
Actually,
Who knows I really think a good intercooler and a little cooler temps might make a difference. It was about 95 and 50% humidity don't know exactly how all the corrections work on that but I think it's still possible.
My build is an attempt to get as close as possible to the impossible. Build a car, cheap, fast and reliable.
If you take out the cheap and go AEM with speed density with a really good IC I'm sure there's more to be had.
just 22 more ft/lbs and we're there.
zelstin
05-09-2011, 05:25 PM
I think you're just pushing the gas pedal down harder than everyone else :D Congrats for a badass street car!
Chris@Rvengeperformance
05-09-2011, 05:28 PM
very happy for you mike! Just think you could hit 600 with 19ts ;)
FeaRpb
05-09-2011, 06:08 PM
Take me for a ride Mike. Looks like Texas will be a record setter this year.
RealMcCoy
05-09-2011, 11:46 PM
Are you still running stock wastegate actuators?
vr3.9
05-10-2011, 12:17 AM
Are you still running stock wastegate actuators?
Stock wastegates or just like Rob installed them. In fact since I assume they came off my old turbo's they have about 270k on them. Wastegates and timing, I guess the next things I need to learn about.
DuTTch
05-10-2011, 03:46 AM
Stock wastegates or just like Rob installed them. In fact since I assume they came off my old turbo's they have about 270k on them. Wastegates and timing, I guess the next things I need to learn about.
be done while you are ahead!
vr3.9
05-10-2011, 08:57 AM
be done while you are ahead!
Yea, I had planned on going blow thru and adding an ITC. But, now I don't plan on doing anything to it but new rear struts and maybe a lighter exhaust. Some sound deadening and cosmetics are on the table too.
what are your fuel mods? with SAFC?
vr3.9
05-10-2011, 11:27 AM
what are your fuel mods? with SAFC?
here, I'll edit my sig for you.
PTE 780CC injectors, AFPR, E85, 3.5" Granatelli MAF, MAFT, FMIC, Dejon intake pipes, Vacuum Reduction, EGR block off plate, Hot Wired Walbro 255 and inline Walbro 255, SAFCII, Turbo XS BOV, 3SX FP hotwire,
I think the key elements here are the AFPR and inline walbro. They let me get plenty of E85 to the injectors.
so 720cc inj is plenty for 500awhp. and two pumps. I wanna use two 340lph pumps, should be enough. and was thinking about 880cc, but I guess I don't have to get bigger than 720cc. do you have a fuel loop or dual feed?
just trying to research before I do my fuel mods. I have 13Ts and my goal is 500awtq. I'm sure I will have plenty of HP.
Jesters Deadd
05-10-2011, 05:12 PM
Nice! What psi were you at at 5600 rpm and then on to redline?
Ninja Performance
05-10-2011, 05:23 PM
Very nice results.
-Chris
UTRacerX9
05-10-2011, 05:36 PM
so 720cc inj is plenty for 500awhp. and two pumps.
Hold on a minute there, and be sure to note that he's running E85 for his numbers. On regular gas, 500hp doesn't require two pumps or 720cc injectors. Just clarifying in case someone reads this thread and misses that part.
Hold on a minute there, and be sure to note that he's running E85 for his numbers. On regular gas, 500hp doesn't require two pumps or 720cc injectors. Just clarifying in case someone reads this thread and misses that part.
my car hasn't seen the premium (93) gas in years. e85 only. :)
vr3.9
05-10-2011, 05:47 PM
Very nice results.
-Chris
Thanks Chris,
I'm glad beepbeep had the link to the quicklist in her sig. I submitted for the dyno thing.
Hold on a minute there, and be sure to note that he's running E85 for his numbers. On regular gas, 500hp doesn't require two pumps or 720cc injectors. Just clarifying in case someone reads this thread and misses that part.
I'm a bit confused because I know I posted just above that my base fuel pressure is 55 making them 877cc injectors. That made them run about 84% @ 501hp and base 43.5 they hit 100% at 471 and wouldn't do any more.
720's on E85 @43.5psi will not be enough to reach 500awhp in my experience.
Wonder where that post went.
vr3.9
05-10-2011, 06:00 PM
Nice! What psi were you at at 5600 rpm and then on to redline?
you can see in the first run it abouut 20 and drops to 19
The second one its 21 drops to about 20.
I did a 24lb pull but since my profec b limit was set to 1.6bar it cut off. From what I could see though it just might hold 24 dropping down to 23. The intercooler was hot and I was happy so I didn't want to try any more. Maybe next time.
http://i225.photobucket.com/albums/dd64/reachmercer/Picture005.jpg
http://i225.photobucket.com/albums/dd64/reachmercer/Picture006.jpg
Gearheadvr4
05-10-2011, 10:23 PM
Nice Mike! That car has come a long way since I met you years ago at your first DFW meet! You've turned her into a monster 13T car. Very impressive.
What do you think of the PTE injectors? I'm considering going with them also since my deal on the denso 720cc fell thru.
Love your new sig too. It's nice to be "the best in the world" at something. I think my VR4 is going for "the most time in the world on on jackstands!"
vr3.9
05-10-2011, 10:46 PM
I guess the 780's are good. Too big for me to run much boost on pump though. Hopefully I want have to be switching back and forth too much any more. Yea she's come along way from the over 200k miles of pure neglect and lack of maintenance and care. First time down the track it was a 15.9 giving it all she had. Pretty sure it used to be the worst VR4 in the world.
This is what it looked like my first 3s meet and Sneeky Pete's.
http://i225.photobucket.com/albums/dd64/reachmercer/mine-1.jpg
much better now
http://i225.photobucket.com/albums/dd64/reachmercer/tx%20gathering%2010/killerglass.jpg
3kgt_tt
05-12-2011, 04:01 AM
how hard is it to convert to E85?
Ninja Performance
05-12-2011, 08:51 AM
how hard is it to convert to E85?
You just need enough fuel pump and injectors and a stainless steel filter element in your fuel filter. E85 requires roughly 35% more volume of fuel for eh same HP than gas. And a fuel controller if you don't already have one.
-Chris
how hard is it to convert to E85?
its not hard to convert to it, its just hard to get off e85. you just become addicted to it. and "you can't stop, 'till you get enough" and its never "enough". just like drugs, I guess.
HilbillyHomeboy
05-12-2011, 10:28 AM
Good show Mike! :cool:
Jeremy
Wow, 500awhp on a mustang dyno and 13Ts on a 3L? Awesome!
Congrats on getting it done. That must be absolutely beastly for some fun daily driving. :)
93SlugTT
05-12-2011, 09:08 PM
i guess this means i can hit my goal of 500 on 15gs lol
nice numbers mang! im sure its a blast to drive
holy crap 15.9 when got it , did it have a rod knock lol
500whp with 13t's is pure insanity--especially on a 3.0L engine. something tells me that we're going to see td-04 world record HP numbers in the ~800whp range before too much longer...also on a 3.0L.
Show Killer
05-13-2011, 09:46 AM
Very nice numbers, it has been a long time coming. I am about 75% sure that i am going to the NG this year. My car has not changed at all from last year. In fact, it still has the messed up rear bumper where it got hit almost 2 years ago and it is still idling high like it was at NG last year. I think since last NG it has had maybe 200 miles put on it. Been sitting in a garage or storage unit for the last year now.
vr3.9
05-13-2011, 11:11 AM
Very nice numbers, it has been a long time coming. I am about 75% sure that i am going to the NG this year. My car has not changed at all from last year. In fact, it still has the messed up rear bumper where it got hit almost 2 years ago and it is still idling high like it was at NG last year. I think since last NG it has had maybe 200 miles put on it. Been sitting in a garage or storage unit for the last year now.
With all the stuff you've done for the idle, did you change out with a good fiav? I know when mine was doing that after doing everything imaginable that's what fixed it. If you could haul 2 cars I'd be real tempted to just be like you and go sit and drink beer tell lies and call it a great weekend.
UTRacerX9
05-13-2011, 03:15 PM
Mike, what spark plug gap are you running? I didn't see any ignition boosters in your sig, so I'm curious what gap you had for 20+ psi.
HilbillyHomeboy
05-13-2011, 03:27 PM
Mike, what spark plug gap are you running? I didn't see any ignition boosters in your sig, so I'm curious what gap you had for 20+ psi.
Good call. That's a likely reason of why it was breaking up, up top...spark blow-out. :)
Jeremy
vr3.9
05-13-2011, 04:33 PM
22 I don't think it's spark blow out, could be wrong. First pull is always beautiful. I let it sit and cool for awhile before the final 501 pull and it still did it but barely. Curious though, I've never really heard of where stock ignition runs out if your gapped down. I would like to run more gap, because I'm sure that's part of the reason my fuel mileage isn't any better.
UTRacerX9
05-13-2011, 05:25 PM
Wow, at .022 I'm sure you're leaving some horsepower on the table, regardless of the cooler temp that ethanol burns at. I bet if you got an HKS DLI and gapped at .032 you'd hit your 500lb of torque number.
Show Killer
05-15-2011, 12:34 AM
I put a new ISC motor on it today and nothing, still the same. Idling between 2 and 3 thousand. We would need a 3 car hauler because Don already wants me to haul his out there.
vr3.9
05-15-2011, 10:11 AM
I put a new ISC motor on it today and nothing, still the same. Idling between 2 and 3 thousand. We would need a 3 car hauler because Don already wants me to haul his out there.
So have you changed the FIAV. If you havn't I'd bet you a bottle of Dickel that's it. lol
GTOJOE
08-10-2011, 03:50 AM
Evil Empire Performance claim to have a car running 13T's pushing 527AWHP.
GTO and 3000GT 13T Turbo Conversion Kit [EE13TCON] - £795.00 : Evil Empire Performance, GTO 3000 Shop (http://evilempireperformance.co.uk/gto-3000gt-shop/index.php?main_page=product_info&cPath=22_29&products_id=38)
I can't seem to find what type of Dyno they have though.
HilbillyHomeboy
08-10-2011, 09:43 AM
It says BHP, though we've went round and round for years about UK dyno's and how exactly they read.
Jeremy
vr3.9
08-10-2011, 10:56 AM
Whew.... Had me nervous there for a second. I have plans of adding a twin fire and then hopefully I can run 24psi with a larger plug gap. Might give me enough to break even their BHP numbers. It's all just guess work still at this time. Turbo's seemed to hold 24psi pretty good till ignition went crazy. Don't know how far it will hold or if it will make anything more than just hot air at that level. But, hey I gotta try.
is it normal for 13Ts to drop 2psi by the time it gets to redline?
DocWalt
08-11-2011, 09:48 AM
Yes we are the original suppliers of the infamous 13T Turbo conversion and again we have moved the game stakes higher......
What? lol
GTOJOE
08-11-2011, 09:49 AM
It says BHP, though we've went round and round for years about UK dyno's and how exactly they read.
Jeremy
Got this reply from Rob at evil empire
Hi Joe
I thought that paragraph had been removed from the website as below it it quite clearly states about the 450+BHP from them.
That car was dynoed a long time ago and i cannot be sure that the figures are correct now we have better dyno's such as the Dyno Dynamics System that prove reliable time after time figures...
However 13T's will happily produce 20PSI all day long and i have been in cars that Produce 24PSI with 0 Knock...
We need to get some more people to finish their cars and get them set up and dyno'ed properly and then we can all see the results.
Cheers Rob
is it normal for 13Ts to drop 2psi by the time it gets to redline?
I think a drop is normal.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.