PDA

View Full Version : what is wrong with it?



a2j
05-06-2011, 11:47 PM
ok, I've been "building" my car for the past year or so. with big pauses in between.
But it finally starts, or was starting I should say.
I'll tell you what is going on, and you tell me what do you think is wrong here. I'd like some input before I start investigate.
I was able to start a car with fresh gas. Oil temps and pressure in OK range. Water temp is also fine. EGTs were at 600-700 after 3-5min idle. Car was always idling at 1500rpms. Didn't go down. AFRs started at 14-15 and dropped to 18+ after a few seconds and stayed there. I'm 99% sure that there is no vac leaks. Gauge reads -18 vac. Engine sounds a little rough, but not too much.
then it died, and I can't hear my fuel pump anymore.
I guess, I will be replacing pump, filter and plugs.
So, any ideas on why that was going on during idle?
Fresh pump gas, 450cc inj. without SAFC correction.

thank you for your input.

mb3000
05-06-2011, 11:55 PM
Not sure if it's just me, but those EGT's at idle seem a bit high. I never get over 500 at idle.

BaadVR4
05-07-2011, 09:35 AM
Rethink the vac leak issue. All three of the 95 VR4s in my family have -20 at 1000 RPM. If revved to 1500 in neutral, it is closer to -22. The high idle and low vac sound like a vac leak or IASC issue to me. The AFR going dead lean doesn't necessarily mean there is a lack of fuel. If the plugs don't fire, the raw fuel and lots of Oxygen are pumped into the exhaust, so the O2 sensor thinks there's lots of Oxygen (which there is) and reads lean. The IASC controls bypass air for warm up and could give these symptoms if it isn't working or working incorrectly. You should also check the fuel pressure before you change the pump/etc. If the pump or filter is bad, it could cause these symptoms, but the vac is low, IMHO and I'd check the things that cause that first. Just my .02.

a2j
05-07-2011, 12:52 PM
wow, thanks. talk about fresh ideas...

so vac should be around -20? I did some vac reduction (obviously), I don't even have clutch vac assist. my vac readings before were -16.

a2j
05-17-2011, 11:02 AM
ok, a little update.
after replacing plugs and filter, car runs/fires more smooth. vac is in -18 -20 range. AFR still jumping from 14-18. EGTs at 700. oil pressure is at 80psi.
idle is at 1500 rpm (-/+ 100) even when coolant is wormed up. I don't know why. any ideas?

a2j
05-25-2011, 02:51 PM
so what can cause 1500rpm idle?

OhioSpyderman
05-25-2011, 03:58 PM
Incorrect BISS setting?

Bob.

a2j
05-25-2011, 06:16 PM
incorrect what setting?

DocWalt
05-25-2011, 07:00 PM
Base Idle Set Screw setting. I don't know the details of the procedure, but it involves grounding a socket thing and setting the BISS.

OhioSpyderman
05-25-2011, 07:14 PM
Actually, it just involves adjusting the screw (it faces you out of the front of the Throttle body, normally covered with a cap, but all I've seen have been without...)

Not sure how to describe where it is, but it's very visible standing in front of the engine....

Turning the screw one way will reduce the idle RPM's, turning it the other will increase them.

Flat tipped screwdriver and 10 minutes TOPS should fix this...

Bob.

speedy25
05-25-2011, 07:39 PM
Before messing with the BISS, test and clean the IAC. Its the cause of 99% of idle problems.

-SP

DocWalt
05-25-2011, 09:11 PM
I thought you always needed to ground that thingy. Ah whatever, the only time I had idle issues was when I forgot to clamp something or plug the MAF in.

OhioSpyderman
05-25-2011, 09:17 PM
Before messing with the BISS, test and clean the IAC. Its the cause of 99% of idle problems.

-SP

I VERY much agree with Speedy :)

Bob.

a2j
05-26-2011, 09:32 AM
I replaced IAC couple of years ago... could it go bad while car was just sitting in the garage?

OhioSpyderman
05-26-2011, 09:52 AM
Probably not, but the hour or so you would take checking it out is time well spent :)

Bob.

Hans@GZP
05-26-2011, 01:29 PM
Grab the throttle plate and make sure it is closing all the way. TB could get stuck partially open or your throttle cable could be adjusted too tight. Also, if you had the TB off the plenum, make sure the gasket's tab is at the top and close to the fire wall. If it's closer to the front of the car, that's your vacuum leak and cause for high idle.

a2j
05-26-2011, 01:32 PM
if you had the TB off the plenum,

I will be checking that. thanks

ver fer
05-26-2011, 08:00 PM
Also make sure that you TPS read less than 10% on your datalogger.

a2j
05-31-2011, 11:09 PM
ok, I did some adjustments with throttle. got it to idle somewhat decent. 1k rpms. still lean, but steady. water and oil temps are at 180F, is it normal for idle? egts around 500F. low fuel trim 120%. O2s cycling. 32 timing. 60psi oil pressure (10w40). throttle position 4-5%, 0% on SAFC.

it died couple of times out of nowhere. MFI relay was clicking a few time right after. dk

I want to make a fathers day gift for myself, take it to the car show that day. it needs to be running, obviously.

Hans@GZP
06-01-2011, 09:08 AM
If the mfi relay is clicking on and off, I would look at your ecu. If you have a 91-93, it sounds like it's on the way out.

a2j
06-01-2011, 09:31 AM
car is 93, and I have 92 ecu. "on the way out" you mean capacitors?

Hans@GZP
06-01-2011, 10:12 AM
Capacitors and there are a row of black "ic's" that can go bad as well.

Tackhammer
06-01-2011, 11:56 AM
car is 93, and I have 92 ecu. "on the way out" you mean capacitors?Have you checked the base ignition timing?

a2j
06-01-2011, 12:18 PM
no I have not. how do I do that?

Tackhammer
06-01-2011, 12:21 PM
I guess it depends on how your cas(s) are set up since your using 2 different operating systems

a2j
06-01-2011, 01:28 PM
so I should get 93 ecu?

Tackhammer
06-01-2011, 01:44 PM
It wouldnt hurt, but its just a longshot and something i noticed nobody else had noticed or mentioned.

regardless of how the car is set up, i think the testing procedure is the same - Warm up the engine, disconnect any loggers, ground the ign timing adjust terminal, (i dont know if 93+ still had this off the top of my head though) and put a timing light on the #1 plug wire, and shoot the crank pulley with it and note what the timing is. If it out of spec on a 91-92 you adjust the cas, if its out of spec on yours the next thing to do is do the same thing using a 93 ecu

a2j
06-02-2011, 09:50 AM
the reason I didn't even think about that, because I thought that there is nothing to "adjust" on 93+ cars. and for some reason I don't think timing is my issue, but I could be wrong.

btw, I have lots of things missing from the engine bay, like vac lines, a/c, solenoids on firewall, etc... even my alternator runs straight from the CS pulley.

Hans@GZP
06-02-2011, 09:52 AM
The response times between the 91-92 sensor and the 93+ sensor are different, so you can end up with unwanted timing advance or retard. Your best bet would be to get either a 91-92 CAS or a 93 TT ecu.

a2j
06-02-2011, 10:19 AM
I'm looking at getting aem ems, but for now I just want to drive it. can't I use 92 ecu? won't be making above 300whp. besides, what exactly wrong with timing advance? my timing at idle didn't change when I was on 93 ecu.

a2j
06-03-2011, 10:39 AM
my passenger fan works now. ;) it didn't before. would the other fan work without those relays on the driver side? also I have discovered RJ45 plug in my car. turned out to be a gigabit satellite connection. Now I have free Internet in my car. lol :P

Tackhammer
06-03-2011, 11:12 AM
would the other fan work without those relays on the driver side?Not unless you wire it up to something else
also I have discovered RJ45 plug in my car. turned out to be a gigabit satellite connection. Now I have free Internet in my car. lol :Pprob a mobile phone connection, a lot of 3s's had these

a2j
06-06-2011, 11:00 AM
I took the cover off of the ecu. looks kind of bad, a little. so I will send my original ecu for a rebuild and see what happens.

a2j
06-26-2011, 01:11 PM
oil/water temps are at 180 idling/cruising. is it normal?

I don't have relays anymore, so how can I hot wire driver side fan, to keep it ON all the time?

Hans@GZP
06-26-2011, 04:14 PM
Temps seem good.

You would have to wire in a relay so the fan would turn on when the car turns on. Or get a fan controller so it can turn on at a certain temp.

a2j
06-27-2011, 10:08 AM
I was thinking like getting a hot wire on the connection that stock relays were plugged in to. or something.

a2j
07-12-2011, 01:52 PM
if I have an exhaust leak before A/F sensor, would it show lean?

DocWalt
07-12-2011, 02:54 PM
Normally, yes.

THE_FATTIE
07-12-2011, 03:12 PM
This is way similar to what Im going through..... Not to thread jack but things to check....

1Vac leaks
2IAC
3TPS
4BISS

Sound right?

Any chance this could be coil pack related? I got a bug in my ear that keeps saying coil pack.....

Also I have almost all of the exact same issues except my idle seems low... and my battery keeps dieing....

a2j
07-23-2011, 07:01 PM
today I finally figured out why A/F were lean. fixed that. took car for a little ride (~5 miles). it was running rich. 11-13 a/f at cruising.
than I got back. after about 5 minutes started again, it idled for 1 min and died. it won't start again. it will start with starting fluid, run rough for a little and die again. why?

any ideas?

THE_FATTIE
07-24-2011, 12:24 AM
What was the problem and what did you do to fix it?

shmoo
07-24-2011, 12:48 AM
ediT: guess he fixed it already.

a2j
07-24-2011, 12:58 AM
I found an issue that was causing a low fuel pressure. The rest is in my previous post. It was running fine and after 5 minutes of sitting on the driveway its not starting. could it be fouled plugs? I drove it for a little with very rich mixture.

Simace
07-25-2011, 08:31 PM
Sounds like you're dumping too much fuel at idle, not allowing the car to turn over. Pull a plug after attempting to turn it on and check to see if it's wet with fuel. If it is, then you know you're problem - too much fuel at idle. BTW, what was it you found n fixed regarding fuel pressure?

Also, from an earlier post of yours, your TPS (Throttle Position Sensor) should be reading 13% at idle, not 4-5%. Little more...

At Idle (warm)
Idle: 650-700 rpm
TPS: 13%
TIMA: 15*
Vacuum: -18 to -20
Coolant: 17x-185 *F

Good luck

a2j
07-25-2011, 11:48 PM
... BTW, what was it you found n fixed regarding fuel pressure?

Also, from an earlier post of yours, your TPS (Throttle Position Sensor) should be reading 13% at idle, not 4-5%. Little more...


hose was a little lose in the tank.
safc reads 0% tps, logger about 10% right now I think.

PS: to my surprise, I was able to adjust safc setting for wot. its was 11.5 with 5.5 ponds of boost. but idle and cruzing AFR were all over the place, mostly rich.

Simace
07-26-2011, 01:57 AM
Sounds like your S-AFC isn't connected correctly or isn't connected completely. Also, your TPS should be 13% at Idle. Given what you're experiencing, I'd play it safe and NOT boost until you've got the basics where they need to be.

I'd recommend heading over to stealth316.com as it is an excellent place to learn more on these basics (and how-to's and what to look for, etc.) If you continue going about tuning the car with the way it is, you're just making more work for yourself as your tunes' foundation is bad. If the basic stuff is all good and within spec, your tune should stick and the results of changes to your tune should be predictable.

FWIW: the TPS is touchy and needs to be calibrated correctly. You can't just dial-it-in, so to speak, with the engine running.

a2j
07-26-2011, 01:21 PM
well, for now I just need to start it up again. as far as tuning goes, not the first year I'm playing with this car. I think I'm very close to get it back on the road.

a2j
08-01-2011, 01:38 AM
it was fuel pressure issue again. don't know why I'm having issue with that fuel hose that is in the tank. but for now, car runs good. 10psi and its faster than it ever was. do these things run 10.5 afr from the factory?

a2j
08-02-2011, 12:21 PM
car runs pretty good now. cruzing and wot afr look normal. pulls pretty good at 10psi. but I don't like my idle. does TPS should be at 10-15% at idle? my logger (two different software) shows only 4-5% and safc shows 0%. what is it really should be at and where do I start to fix that? I thought that throttle should be completely closed during idle.

DocWalt
08-02-2011, 01:09 PM
My TPS was 11% according to my logger and I never had an idle issue. IIRC the logger should see the TPS as 10-15% as you said.