PDA

View Full Version : For Sale Limited Time- Pampena Motorsports Bellhousing Braces- 5 or 6 speeds



WidowMaker
04-20-2011, 09:22 AM
We are having a limited time offer for installed bellhousing braces. $250 installed. That's $50 off of our regular price.
So if you've been thinking about doing it, now is the time. Send your Bellhousings to:
Pampena Motorsports: Trans Dept.
855B South First St.
Ronkonkoma NY, 11779

1 day turnaround time! This price is for a limited time only.

$250 installed brace.
$125 brace only.

-Steve
http://www.pampenamotorsports.com/images/getragimage.jpg

TurboSinceBirth
04-21-2011, 03:30 PM
Who has broken a 5-speed bellhousing? I didn't think anyone had yet, but I couldn't remember for sure. I have upgraded the OS, front, and mid housing on the transfercase. I'm pulling the motor and tranny back out which would be an ideal time to do this, but I didn't think it was necessary. 6-speeds yes mandatory. I'd rather spend the money on a better front diff though while it's out.

WidowMaker
04-21-2011, 08:40 PM
We always say "better safe than sorry." If you want the strongest tranny possible, you need a bellhousing brace. The 5 speeds can break, it's just that the 6 speeds are much more prone to it. For the peace of mind, it is well worth it for both 5 and 6 speeds.
-Steve

TurboSinceBirth
04-21-2011, 09:33 PM
We always say "better safe than sorry." If you want the strongest tranny possible, you need a bellhousing brace. The 5 speeds can break, it's just that the 6 speeds are much more prone to it. For the peace of mind, it is well worth it for both 5 and 6 speeds.
-Steve

Yeah I realize that. I just don't know that it'll be a weak link for my setup. I don't have upgraded 300M rear axles which will be on the list depending how far I push the car. My Southbend Stage 4 clutch is only going to go so far too so if I max that out I may put a brace in at the same time.

deathsled
04-24-2011, 10:34 PM
Should one take out all the seals and such before sending a bell housing in? What's the standard protocol?

terrets
04-24-2011, 11:26 PM
What do you have to do to install the brace?

deathsled
04-25-2011, 01:28 AM
Grind the bellhousing for clearance and weld it in place

terrets
04-25-2011, 04:10 PM
So is the brace aluminum?

WidowMaker
04-26-2011, 04:32 PM
Should one take out all the seals and such before sending a bell housing in? What's the standard protocol?
You can leave everything in it, just clean it really well and send it on it.

So is the brace aluminum?
Yes, the brace is aluminum

Mike Vincent
06-15-2013, 10:08 AM
Who has broken a 5-speed bellhousing? I didn't think anyone had yet, but I couldn't remember for sure.
I just broke my 5spd bellhousing in that same exact spot. I need a new bellhousing, and a brace....and a tranny. :P It might be savagable, we'll see. I have tons of trans parts.

But yeah, do you guys still have the 5spd braces? If so, I need to get that done ASAP!

CGSTEALTH1791
06-16-2013, 03:33 PM
any idea on what kind power rating these are good for?

anyonebutme
06-16-2013, 05:14 PM
They withstood 700+ AWHP from Ray Pampena beating the ever living hell out of it for years, on a 5-speed at least. On a 6-speed, it'll far outlast the transfer case gears.

I'll go ahead and say you can't break it without doing something dumb like clutch dumping on slicks for years straight.

sergechronos
06-18-2013, 02:48 PM
I'll go ahead and say you can't break it without doing something dumb like clutch dumping on slicks for years straight.

Don't say shit like that. Somebody is likely to take it as a challenge.