View Full Version : Air Conditioning. Possible retro fit.
EvanH
04-17-2011, 10:27 AM
Well, my ac went out years ago, and I am still contemplating getting it to work again.
If I want to keep it R-12, I can buy the refrigerant on the internet and do it that way, along with resealing all the possible locations it could have leaked from, like O-rings and the like.
But if I wanted to make it into the R-134 system what all do I have to change or flush?
I can see I would need a new expansion valve, filter drier, different O-rings, and refrigerant. But what about the compressor or condenser, Evap core?
How hard of a task would it be to replace the expansion valve? I would have to remove the dash right?
Anyone know of a walk thru? I searched.
OhioSpyderman
04-17-2011, 10:30 AM
The only thing I did when I switch over to R-134 in the Stealth was have my mechanic friend evacuate the old system, then recharge it with R-134 (new fittings are required, but come with the switchover kit). Been cold for going on two years now. Total cost to switch, < $50.
Mine was not leaking, just low on charge....
Bob.
EvanH
04-17-2011, 10:57 AM
Mine blew freezing cold one day and hot air the next, my compressor clutch wont turn on. It works, I jumped the relay to check, so I am guessing it blew a seal maybe.
And if it matters I have the auto AC.
OhioSpyderman
04-17-2011, 11:48 AM
I'm not 100% sure (but fairly sure) that the compressor won't come on if there isn't enough freon in the system. You could always add a "dye" charge, see if it comes on for a bit and then check for leaks with a black light.
Or, better yet, maybe someone on the board with REAL A/C skills could tell you EXACTLY what to do....
Bob. :)
Zaroth
04-17-2011, 04:00 PM
I have a 92. Would my car have an r-12 system or r-134? My car is in dire need of some more freon.
OhioSpyderman
04-17-2011, 04:21 PM
I have a 92. Would my car have an r-12 system or r-134? My car is in dire need of some more freon.
I believe 1993 was the year they switched, and that the 94 models were the first to have 134a.
That being said, unless someone already did the conversion on your car, its likely to have an R-12 system....
Bob. :)
UTRacerX9
04-17-2011, 05:15 PM
Switching to 134 doesn't require any parts, just the conversion kit, as Bob stated, they run about $50. They only thing you need to do is make sure the system has been evacuated first. If you have a leak, it is typically a compressor seal that goes, and you can check for leaks using a black light and some dye. I need to do this myself actually, just haven't gotten around to it.
EvanH
04-17-2011, 05:53 PM
So I don't even need to switch the expansion valve? I figure I would get a new drier for precaution and also I would just replace all o-rings then. How much colder or not colder does the 134 run compared to the 12?
GTOJOE
04-17-2011, 09:04 PM
If doing this you SHOULD replace the recieved/dryer and every o-ring in the system. However as stated it's not essential. As for identifying the type of gas you can tell by looking at the 2 fill locations. The R123 gas has to caps usually red and blue that unscrew while the older type is usally just black caps and smaller connections. See pics in the below thread. Also there is usually a sticker in the engine bay advising what type it is.
Air conditioning doesn't work...what to do (http://forum.w116.org/mechanicals/air-conditioning-doesn%27t-work-what-to-do/)
However.... some ppl have been know to fill R12 systems with R134 without changing the fill valves so it can be very hard to work out. The correct process involves replacing the section of hose with the connections on it to the new type conections or buy adapters that adapter the R12 to the R134 type.
GTOJOE
04-17-2011, 09:06 PM
Also R12 is usually more efficiant so it will be colder with R12. However R134 is "better" for the environment.
jbuhrman
04-18-2011, 07:45 PM
R-12 is no longer availble for purchase, the R-12 you see is either left over stock piles or sometimes stolen. And by 2013 there will be no legal sales of R-12 within the US.
If you do a change over, you actualy want to change the compressor oil as well as a mix of refridgerant can cause an unreliable system since the 2 boil off at different temps/pressures.
If you need any help just PM me as I can assist in pretty much everything on the legal side as AC's are my specialty and I am certified for auto work as well.
EvanH
04-18-2011, 10:54 PM
What is a good flush? As to evacuate, and purge? Working on the helicopters, we have had to flush by just running freon in the cold, and capturing it from the hot in an empty bottle. Long, annoying, process.
FluffyCow
04-21-2011, 07:01 PM
There's two things you can do to flush the system. They sell this stuff called "Turbo Kleen" at HVACR supply houses that you can use. You'll need a source of clean nitrogen though. OR, you could use R-11 to flush the system as well. It's availability I have no clue on, as my company had 3 drums of it laying around.
Basically, if you want to change freon, you can use other types of freon in place of the R12, though I do not know how legal it is, DOT-wise. R409A can work, as it's PT chart is very similar to that of R12. MP39 works as well(Don't remember the R number though), and it's even closer to the PT chart. If you wanted to convert to 134a, you'd need to change the expansion valve and flush the system really, really well. You'd also have to drain all the compressor oil out and replace it with 134a oil(12 is mineral oil, 134a is alkybenzene or POE oil). You might also need adaptation fittings from the automotive fittings to regular HVAC fittings, or get an automotive charge/test manifold.
The fittings don't determine refrigerant type, either. My 91s and 92 all have teh automotive fittings, and they're R12. The change was to keep unlicensed people(say, an HVACR mechanic) from working on an automotive system.
Also, what I would do first would be to pressurize the system with clean nitrogen(if your system is completely flat) and then check every AC line/fitting with soapy water or gas-leak detector(basically paying for soapy water, lol). Also, watch the pressure. If you pressurize the system with 100PSI of nitrogen, it WILL NOT move unless there's a leak. Nitrogen isn't temperature-reactive enough to register on an HVAC gauge for temp flux.
I can't think of anything else right now, but just shoot me a PM and I can try to explain in more detail.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.