View Full Version : This TC keeps spewing oil
q2418130103p
04-16-2011, 07:06 PM
So I put the car away for the winter, and everything under the car appeared normal.
I put the car up on the lift this morning to get it ready for the season and found the TC COVERED in gear oil. The car hasnt moved in 6 months...
The fluid appears to have come from the vent cap. I drained the fluid out and found 7 ounces, a bit shy of the full 9.28 ounces that is supposed to be in there. Since it is shock proof heavy there was probably at least 1.5 ounces left in the TC, plus the car was at a slight angle, so there was some fluid left in the tail section.
Anyone have any ideas about this? I dont want to just fill up the TC and have this happen again. SOmething similar happened last year, however I believe that time it was slightly over filled, and it came out of the vent while moving.. not sitting in storage.
Chris@Rvengeperformance
04-16-2011, 07:11 PM
I switched to redline 75w90 because the shockproof comes out the breather so bad.
There are modified breather setups that will fix the problem, but I didn't really feel like messing with it or adding more complication.
q2418130103p
04-16-2011, 07:16 PM
Hm, interesting.
Well I have plenty of the 75w90, so I can go ahead and fill up with that instead. Should I flush out the shock proof with some motor oil first?
Is there a guide/thread about the modified breather setup?
O yea, anyone know where I can get stuff like crush washers locally? Like the one for the drain plug. I would hate to have to order something like that.
Chris@Rvengeperformance
04-16-2011, 07:17 PM
I didn't flush mine, but it wouldn't have hurt.
There are some guides on here and the other site. I'm sure you can find the crush washer anywhere if you bring the old part with you.
q2418130103p
04-16-2011, 07:18 PM
I'll pump some 5w-30 through to clean it out.
THanks for the help, I'll poke around for guides.
q2418130103p
04-17-2011, 11:44 AM
So you would be surprised at the lack of places that carry aluminum crush washers...
If anyone happens to read this and knows about the breather modification, that would be most helpful, I am having a bit of trouble finding that.
I guess I am having an off 'finding stuff' day.
Chris@Rvengeperformance
04-17-2011, 02:49 PM
use some copper washers if that's what they have:
Remote oil resevoir for TC?. - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f42/remote-oil-resevoir-tc-393514/)
FYI I have re-used the drain plug washer many times.
J. Fast
04-17-2011, 02:55 PM
Buy a stainess flared barb fitting and tap it into the old breather vent socket and run a hose from the barb fitting to one of these. I used to make them but since I found this place this is where I get them now :) .
North East Xtreme Tech (http://northeastxt.com/vent.html)
GTOJOE
04-17-2011, 09:24 PM
^^^^this^^^^ was going to suggest a remote mounted vent. Been thinking about doing the same thing. Those vents look good.
q2418130103p
04-18-2011, 09:27 PM
So how much line is really needed before terminating at a remote vent? A few inches, a foot? There isnt much fluid in the TC, so I imagine a large tube is not needed. It looks like Erron terminated his connection into a reservoir. Seems to me that the tube itself should act as a reservoir.
If I use the regular redline 75w90 will I still have this problem?
Would it be worth it to just replace the factory breather as a stop-gap measure? Mine doesn't appears to be damaged, but it is certainly worn in.
BTW, thanks for finding that thread for me.
q2418130103p
04-22-2011, 10:22 PM
So you guys may know this already, but I noticed the recall manual for the TC calls for 75-90 GL5, as opposed to the regular service manual which says GL4.
Chris@Rvengeperformance
04-22-2011, 10:37 PM
So you guys may know this already, but I noticed the recall manual for the TC calls for 75-90 GL5, as opposed to the regular service manual which says GL4.
Gl5 is better for hypoid gear sets like the tc and the rear end because it has more extreme pressure additives
Sent from my DROIDX using Tapatalk
q2418130103p
04-22-2011, 10:44 PM
So I wonder if mits called for gl4 in the TC originally just to avoid having people put gl5 in the transmission by accident.
Chris@Rvengeperformance
04-22-2011, 11:25 PM
So I wonder if mits called for gl4 in the TC originally just to avoid having people put gl5 in the transmission by accident.
yeah that may be, I'm not sure.
I'm using redline 75w90 GL5 in the transfercase right now. The GL4 oils have to pass a copper corrosion tests which the GL5 oils do not, which is why not all GL5s are safe in the transmission due to our syncro construction, but I am not aware of any materials in the transfercase that GL5 could corrode.
q2418130103p
04-25-2011, 08:19 AM
That would make sense, however I do not believe there was fluid on the TC when I put it away for winter. Which means the only time it could have come out is the one time during the winter that I moved it. And it was a real cold day.
I went ahead and put 7590 in it. I measured the fluid that came out. After I got the TC off I found a lot more fluid in the tail section. All total I have slightly over 9 ounces, which is what I put in before. So the coating of gear oil on the TC was the only oil to have escaped, and it was minimal.
I will keep a close eye on it. I will take it for a ride, get up to speed, get the TC nice and hot, and check for leaks. The TC had the input spool replaced a few years back, I figure it would have failed already if something was done wrong, but perhaps something is just loose as you said.
J. Fast
04-25-2011, 11:10 AM
The only way I can see oil coming out of the top is if it's getting too hot.
That'll happen if there's something wrong inside it, like worn out bearings or the nut on the output shaft coming loose, as they do .
Steve
Friction or rapid acceleration. Take a perfect new in box or rebuilt and re-sealed T-case. Fill it to the normal level. Tap a barb fitting into it and run a clear hose into it into a clear plastic reservoir and mount it above the T-case on the firewall. Put your car in 3rd gear starting at 50MPH and floor it to redline. Do it two times and pull over. I guaraneee the TC oil will have climbed up the clear hose. Measure the diameter of the hose and height and calculate the volume of displaced oil. You can displace almost 10% of the T-case fluid in one pull. I have seen it many many times. I've seen it work flawlessly on straightaway pulls appraoching 180mph. We ran 2 full pulls and nearly 1/3 of the fluid was at one point in time expelled but drained back down.
This is a fix, period. It drains right back in and the T-case and always stays full.
Obviously another one of those things you have never seen, done, or tested. Hell, you don't need to, your car is slower now than it was when it was stock. It will never leak, it'll just beg you to put it back to stock out of appreciation.
q2418130103p
04-25-2011, 12:15 PM
Welp, in my case I dont have a habbit of hitting triple digit speeds, or doing repeated 3rd gear pulls. But I will likely perform this remote reservoir fix next winter.
I think in my case I may just use a fairly large diameter tube, and use the tube itself as the reservoir, on account of my prior statement about my driving habits.
Chris@Rvengeperformance
04-25-2011, 03:28 PM
in my limited experience the shockproof heavy definitely is much worse about coming out the breather than normal fluid. I don't know if it is because of expansion or more likely because of the climbing action it has.
I cannot see a factory stock car with factory fluid having a problem this serious. People who buy 45K cars do not expect to be losing transfer case fluid everything they drive it hard.
Yes, they will not accelerate as hard as modified ones, but even a stock car could hit 155.
J. Fast
04-26-2011, 02:47 AM
That's the dumbest reply imaginable.
So what you're saying is that mine , being stock will be leaking out of the breather, as everyone else's perfectly good ones will be.
Steve
No, read it again. If you ever get your mobile junkyard to accelerate fast enough to cavitate you can bet your ass it will leak. Secondly, why wouldn't you want to extend the breather anyway? Makes draining and filling the T-Case, trans, and rear diffs mindless. If it's broken, fix it? Hrm, pay $20 for a new T-case breather that can be extended into the engine bay... seems pretty simple to me. Furthermore, I never said there was anything wrong with using the stock one. This is however an inexpensive T-Case cavitation and lockup insurace policy, a performance upgrade, and vehicle servicing accesibility upgrade to the T-case.
Argue all you want, the pro's and cost benefit far outweigh the cons. Spend $20... yay smack me cuz that's a lot of money when you own a 3/S :rolleyes3:
J. Fast
04-26-2011, 03:28 AM
Shit, just drill a hole in the floor. And you can use a measuring cup and a funnel to fill from the top. Spec'd amt in the manual is spot on.
aaronatstate
04-26-2011, 11:41 AM
I don't have room in my engine compartment for useless extras.
Steve
Pot, kettle? Useless extras like multiple throttle bodies, fuel pressure regulators, etc etc
q2418130103p
02-04-2012, 09:45 PM
I was just going through my old threads and spotted this one.
Turns out the oil was actually coming out threw the side cover. I don't mean a crack, or a seal, I literally means through the metal. The threads for the level indicator plug stripped so I had the hole welded shut. Turns out there was an invisible hole in the weld. A skim coat of jb weld fixed the problem. That is obviously a temporary fixed, but at least I know what the problem was.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.