PDA

View Full Version : Can I drive w/o secondary 02s?



Modern 3kGT
03-17-2011, 05:58 PM
Can you drive without the secondary 02 senors installed? I have a place to be in a couple of hours and both secondary sensors have not arrived yet. I know they are only there to check an see if the cats are working...

Is it safe?

Thanks, John

RL7
03-17-2011, 06:25 PM
You can drive with no O2s. Check engine light may come on and car will run richer than normal. Perfectly safe though.

dpartinvr4
03-17-2011, 07:46 PM
it will sound weird with nothing plugging the holes.

VR-4 0wnz j00
03-17-2011, 11:02 PM
Lol, it will be loud but manageable.

mb3000
03-17-2011, 11:20 PM
You could put a bolt in there if it's that big of a problem.

x2xtreme360
03-17-2011, 11:39 PM
You can drive with no O2s. Check engine light may come on and car will run richer than normal. Perfectly safe though.

Secondaries are for emissions purposes only. They have nothing to do with adjusting AFR's.

J_Parker
03-18-2011, 01:39 AM
Yep, you can even run on one primary. Just as long as both banks are feeding it.

n2nsanity
03-19-2011, 01:56 AM
Yep, you can even run on one primary. Just as long as both banks are feeding it.

can you elaborate on this? i actually have a problem with this
my car is ca spec, but my engine isn't. it had an o2 sensor on the front manifold, but the ones i'm using now don't.
what can i do about this?

x2xtreme360
03-19-2011, 02:16 AM
can you elaborate on this? i actually have a problem with this
my car is ca spec, but my engine isn't. it had an o2 sensor on the front manifold, but the ones i'm using now don't.
what can i do about this?

The ECU might send the car into limp mode, although I'm not sure if our ECU's will do that. The one O2 would have to run in open loop if the O2 sensor is unplugged.

You could either grab a fed spec ECU that uses the single O2 sensor or possibly splice the front O2 sensor into the rear O2 sensor, that way the ECU will at least get a signal from both sources.

J_Parker
03-19-2011, 03:13 AM
You'll have to splice them together, yes. If you can find yourself a bung and relocate it to about 8 or more inches from where the rear bank plumbs in.

n2nsanity
03-19-2011, 11:52 AM
is the primary the single sensor right before the cat?
or are there 2 primarys? 1 at each exhaust manifold

J_Parker
03-19-2011, 02:23 PM
If it's a JDM you primary will be the one, and only one after the cats, if its a Cali spec, your primary will be the two before the cats in the o2 housings. If it's like anything else though, your two only o2's will be in the o2 housings.

n2nsanity
03-19-2011, 03:30 PM
the car is a ca spec i think. it has an o2 sensor for each manifold and one right before the cat. i have a 6g74 going in. and what was left of the wire harness didnt have o2 sensor connectors.

i also have another 94 base, fed spec i believe. it only has the 1 o2 sensor right before the cat.

i think it will be much less work if i can just switch ecu's

J_Parker
03-19-2011, 03:57 PM
If you can I think that'd be the best rout, cutting into a harness usually isn't something I would want to do.