View Full Version : The Monthly "My Car is Running Bad" Thread
mb3000
03-13-2011, 12:38 AM
Ok guys I am almost positive my problem lies with leaking/bad ECU caps, but I'm just curious if anyone has had any similar problems. I hate electronics and I am really dreading the thought of replacing the caps.
Car is a 92 vr4 with the usual upgrade mods. When driving the car absolutely will not rev past 3000rpm at any boost psi, and will die after letting off the gas.
New NGK plugs gapped to .045"
Engine tone does change if you pull off the plug boot at the coilpack.
Pressure tested at 20 psi, no vaccum leaks.
New fuel filter.
I'm thinking some possible culprits are the plug wires, coilpack, PTU, MFI relay, & fuel pump.
I logged a little bit hoping to get some info, however I am having computer trouble right now so I will try to post them up later.
FluffyCow
03-13-2011, 07:50 PM
Pull your ECU and take a pic of the board inside. If it's nothing that bad, you can find someone here that'll replace the caps for you for a small fee(probably, don't know what people would charge, the set of caps literally costs like $3...). Don't run the car with a bad ECU, it'll screw up all kinds of other stuff.
green-lantern
03-13-2011, 10:41 PM
It's broken ringlands, it's the only reason a car has problems.
mb3000
03-13-2011, 10:47 PM
It looks like at least one of the caps have been replaced before. Here are some pictures, the only signs of leakage that I can see are from the 100uF cap.
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0627.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0628.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0629.jpg
mb3000
03-13-2011, 10:47 PM
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0630.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0634.jpg
FluffyCow
03-14-2011, 12:03 AM
ouch... that ECU board looks pretty chewed up...might need a real electronics place to look into it. That's shitty...though I think you can try cleaning it with electronics cleaner...
Street_Chally73
03-14-2011, 01:27 AM
ouch... that ECU board looks pretty chewed up...might need a real electronics place to look into it. That's shitty...though I think you can try cleaning it with electronics cleaner...
:smartie:
That bottom photo shows some real carnage around the one capacitor.
Rocket
03-14-2011, 02:57 AM
None of those caps look stock either.
mb3000
03-14-2011, 07:11 PM
I'm going to shoot AvPro an email to see if they can do something for me, although I'm not counting on it.
mb3000
03-15-2011, 11:43 PM
Here's the link to the log. Nothing really happens until row 700.
https://spreadsheets.google.com/ccc?key=0AodyujP_Z7XrdC0zeVBwamUybGM2MFFfLW1QdGxXb 3c&hl=en&authkey=CKHMrNQE#gid=0
mb3000
03-20-2011, 12:21 AM
Bump. I would really like someone's opinion of the timing in particular.
mb3000
04-28-2011, 12:34 AM
Just an update for anyone who might be wondering what the issue was, the ECU was sent off to AvPro and has been running great ever since.
mb3000
11-03-2011, 02:32 AM
Well, she's back. Unfortunately worse than before and I'm almost positive it's a problem with the ECU, ARC-2, or 91-92 style CAS.
I'll be ripping everything apart in the next couple days, wish me luck.
vyper1
11-03-2011, 05:56 AM
im having problems as well mines a 94 tho i havent heard ever of an ecu in 94+ car go bad but its identical to the ecu problems i had in my 92. i too am also running thee arc2 92mm big maf car idles revs ect but try to move the car and it backfires/afterfires like crazy just 1 loud bang
curious as to what you find im up for trying anything. havent drivin the car almost at all this yr :(
Roybatty
11-03-2011, 09:58 AM
Well, she's back. Unfortunately worse than before and I'm almost positive it's a problem with the ECU, ARC-2, or 91-92 style CAS.
I'll be ripping everything apart in the next couple days, wish me luck.
Same issues as before? No revving past 3000rpms and no idle? Last time she wouldn't hold idle for me it was the MAS, got a used one from GZP and resolved issue. There is also a vendor in MD that replaces caps on ECS and ECU...I don't readily see them as a vendor anywhere...
mb3000
11-03-2011, 10:33 AM
As of now the car will barely hold 1500rpm, will slowly bog itself to death.
vyper1 you sound like you have the same issue here. In my case, this problem only occurs during the colder months.
Roybatty
11-03-2011, 11:07 AM
I had these guys do my ECU and ECS Auto Velocity | (http://www.autovelocity.net/). It was a bit ago, and IIRC it seemed longer than I wanted it to be, but I am happy with the job.
You sound like you are already trouble shooting using the Fuel section of the manual, I would continue to do that; ensuring you have fuel, spark and air. You are getting it all to some degree.
If you are confident your ECU is okay, my next step would be sensors, I would trade your MAS out with a known good one, also its temperature related/sensitive.
GTOJOE
11-03-2011, 08:02 PM
Unplug your MAF and see if it will rev.
mb3000
11-04-2011, 12:40 AM
I had these guys do my ECU and ECS Auto Velocity | (http://www.autovelocity.net/). It was a bit ago, and IIRC it seemed longer than I wanted it to be, but I am happy with the job.
You sound like you are already trouble shooting using the Fuel section of the manual, I would continue to do that; ensuring you have fuel, spark and air. You are getting it all to some degree.
If you are confident your ECU is okay, my next step would be sensors, I would trade your MAS out with a known good one, also its temperature related/sensitive.
Granatelli MAS doesn't have baro, iat, or any of that jazz. The arc2 itself sends out a 68F and 1bar signal to the ECU, which is a fixed value that doesn't change. I am 0% confident in the ECU rebuild, but I'm not counting on it being the problem.
mb3000
11-04-2011, 01:15 AM
Son of a bitch, looks fine.
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0971.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0972.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0974.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0975.jpg
Roybatty
11-04-2011, 01:30 AM
Unplug your MAF and see if it will rev.
Granatelli MAS doesn't have baro, iat, or any of that jazz. The arc2 itself sends out a 68F and 1bar signal to the ECU, which is a fixed value that doesn't change. I am 0% confident in the ECU rebuild, but I'm not counting on it being the problem.
I have heard some grumblings about AVPRO. Enough, that I decided to try Auto Velocity. I believe some people were very p oed about AVPRO service, or lack of.
The Granatelli sounds pricey, is it old? I guess even the new ones can go bad, but you need to trouble shoot it. You could prolly get a working OEM MAS from GZP (or whichever used parts place) for pretty cheap (30 to 50). The unplugging will get it in a limp mode IIRC but is inconclusive regarding if MAS is actually failing.
edit...ECU does look okay
mb3000
11-04-2011, 01:48 AM
I have heard some grumblings about AVPRO. Enough, that I decided to try Auto Velocity. I believe some people were very p oed about AVPRO service, or lack of.
The Granatelli sounds pricey, is it old? I guess even the new ones can go bad, but you need to trouble shoot it. You could prolly get a working OEM MAS from GZP (or whichever used parts place) for pretty cheap (30 to 50). The unplugging will get it in a limp mode IIRC but is inconclusive regarding if MAS is actually failing.
edit...ECU does look okay
It's the upgraded MAF that comes with the ARC-2. I'll probably be switching back to 360's and stock maf to rule out the ARC-2 entirely. Still might send the ECU off just for the hell of it.
After all, the lifetime warranty was one of the selling points.
GTOJOE
11-04-2011, 02:12 AM
I have heard some grumblings about AVPRO. Enough, that I decided to try Auto Velocity. I believe some people were very p oed about AVPRO service, or lack of.
The Granatelli sounds pricey, is it old? I guess even the new ones can go bad, but you need to trouble shoot it. You could prolly get a working OEM MAS from GZP (or whichever used parts place) for pretty cheap (30 to 50). The unplugging will get it in a limp mode IIRC but is inconclusive regarding if MAS is actually failing.
edit...ECU does look okay
If your MAF is stopping you from reving past 1500k etc then unpluggin it will mean the ECU lopoks at other sensors to run but will allow you to rev all the way through the rev range. But it will run like shit.
mb3000
11-04-2011, 02:20 AM
If your MAF is stopping you from reving past 1500k etc then unpluggin it will mean the ECU lopoks at other sensors to run but will allow you to rev all the way through the rev range. But it will run like shit.
Car runs fine when no load is on the engine. I can dance on the limiter with perfect a/f ratio in neutral, but when load is applied everything goes out the door.
ntcmpjg
11-04-2011, 09:19 AM
It looked like to me in the first pic that the board heap junk on it. If you look at the other pic you can see the brown stuff on the silver dot that it the leaky junk on it
Sent from my iPad using Tapatalk
Roybatty
11-04-2011, 09:43 AM
How did you get your log into google docs? cut and paste?
Very strange how it won't go past 3000 in log. Did you try flooring it?
Only other thing is your spark plug gap seems large for running higher boost. But you didn't mention any knock issues.
mb3000
11-04-2011, 10:32 AM
How did you get your log into google docs? cut and paste?
Very strange how it won't go past 3000 in log. Did you try flooring it?
Only other thing is your spark plug gap seems large for running higher boost. But you didn't mention any knock issues.
Can't remember how I got those logs up :lol:
Yes I had the car floored, nothing works. Using DLI and non-resistor plugs to keep the gap up.
I'm almost positive that this is an electrical issue, as it acted up out of the blue on the highway. Slowly died from 55mph in 5th, downshifting would result in horrid misfiring.
BigTyla
11-05-2011, 04:48 PM
You need to look at the other side of the board as well. I've seen a few boards with leakage that was hard to spot on the top side, but looking at the bottom side clearly revealed damage.
Roybatty
11-05-2011, 05:58 PM
Can't remember how I got those logs up :lol:
Yes I had the car floored, nothing works. Using DLI and non-resistor plugs to keep the gap up.
I'm almost positive that this is an electrical issue, as it acted up out of the blue on the highway. Slowly died from 55mph in 5th, downshifting would result in horrid misfiring.
Your TPS log never seems to show that you floored it. Also, does it bottom out @ 8.5%? Are you using MMCD? TB closed should be close to the same regardless, mine is closed @ 12.5%, and maxes out @ 80 something.
mb3000
11-06-2011, 12:25 AM
Those logs are pretty old, my tps is at 7.25 now and WOT is around 90 because of the CC delete. I'll post a couple pics of the underside of the board in a couple seconds.
mb3000
11-06-2011, 12:40 AM
Upon closer inspection...
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0980.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0981.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0982.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0983.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0984.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/1992%203000GT%20VR4/IMG_0986.jpg
I'll be sending this board back. Displeased to say the least.
GTOJOE
11-06-2011, 07:15 PM
there is nothing wrong with the bottom of that board. They just didn't re-apply the clear coat. The top however I'm not sure off...
Roybatty
11-07-2011, 12:40 PM
Those logs are pretty old, my tps is at 7.25 now and WOT is around 90 because of the CC delete. I'll post a couple pics of the underside of the board in a couple seconds.
What??? You deleted some of your CCs? That will screw it up every time!
;) What is cc delete?
BigTyla
11-07-2011, 02:37 PM
The underside of the board doesn't look too bad, but I see a couple of areas with corrosion. Also, one of your drivers looks funny. It's the leftmost one. Is it leaking? I believe that is the ISC driver.
mb3000
11-08-2011, 12:11 AM
What??? You deleted some of your CCs? That will screw it up every time!
;) What is cc delete?
Cruise control ;)
Tyla, the board has already been sent back to AvPro. Wasn't exactly what I was expecting when I pulled off the cover.:dontknow2:
BigTyla
11-08-2011, 01:17 AM
Well hopefully they can fix everything up.
BTW, remember those ISCs you sent me? They might be good after all. :p The ISCs weren't homing because of the crappy ECU I had!
mb3000
11-08-2011, 01:28 AM
:lol: Wouldn't ya know!
Roybatty
11-09-2011, 11:41 AM
Cruise control ;)
Tyla, the board has already been sent back to AvPro. Wasn't exactly what I was expecting when I pulled off the cover.:dontknow2:
I deleted my CC also, but it didn't affect my TPS closed position, still 12.5%. I am using MMCD, not sure if that makes a difference. You have a stock TB?
mb3000
11-09-2011, 05:09 PM
I use MMCd also, with the stock TB.
Roybatty
01-05-2012, 01:12 PM
Justin...did this issue get resolved? what was the fix?
mb3000
01-06-2012, 12:48 AM
Got a great deal on an AEM EMS from Chris. Best investment in the car I have ever made.
Stock ECU is still with AvPro, apparently he can't find anything wrong with it. However, this post makes me wonder if it's not a damage issue, but rather a function of the ECU itself.
Maybe it has something to do with this? My car somewhat does it, and I have a 99 Montero ECU running mine...
http://i210.photobucket.com/albums/bb53/aaronatstate/WarmUpRetardmap.jpg
Roybatty
01-06-2012, 08:45 AM
LOL, an EMS would trump all other issues since you can control everything now. It sounds like it could still have been the MAS, I know you were in process of trying to rule it out.
That table is showing the ecu timing adjustment map @ warm up...seems strange its programmed to pull timing at that rpm range.
mb3000
01-06-2012, 09:43 AM
Ironically that's exactly where I had my issues. Sometimes I could get out of that rpm range by going WOT but it wasn't easy.
In all honesty that map depicts the exact area where the issues would occur.
BigTyla
01-06-2012, 11:01 AM
Is there a way to edit that map in the software currently available for the 98/99 ECUs?
onebadmollafolla
01-06-2012, 08:32 PM
http://i.imgur.com/oQQHF.jpg
mb3000
01-07-2012, 12:04 AM
I would imagine that it would be possible by using Evoscan but I've got no personal experience with it.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.