View Full Version : PCV'less front valve cover....(pics)
Sin'sVr4
03-09-2011, 09:18 PM
OKay, well I was putting a new pcv valve and the little notch broke off. Well, had a guy reweld some aluminum on and I put a hose barb on instead. I was going to tap into the old hole, but there is a small tube that if you drill into it it will break, plus I dont want shavings in the baffle. Well, this work out better than I hoped. You can see the difference in diameter from teh pcv and the fitting I put on. I use DR Krank vents so the PCV is pointless for me and very restrictive. What do you guys think?
Mike
237223732374
Ninja Performance
03-10-2011, 10:34 AM
I use a threaded barbed nipple fitting that screws into the valve cover like a PCV and gives a barbed nipple to attach a hose to. You can get them from Mcmaster.
-Chris
mh3kgt
03-10-2011, 12:51 PM
I need to do this and install my krank vents. Hopefully it will help my slight smoke on decel issue and not let stock pcv pressurize the heads anymore.
If you're pressurizing the heads, just put some open breathers on for a temporary (that may turn permanent) fix. The PCV valve is meant to be restrictive in high-vacuum situations to prevent too high a percentage of unmetered air from entering the system.
Ninja Performance
03-10-2011, 05:34 PM
It also allows the valve stem seals to seal under vacuum. Otherwise they pass oil and you will see smoke out your exhaust.
-Chris
mh3kgt
03-10-2011, 07:21 PM
^ I know somebody that happened to. He's Green, and you won't like him when he's angry :p
green-lantern
03-10-2011, 07:41 PM
Nobody likes me when I'm nice ether :lo5l:
J. Fast
03-10-2011, 11:39 PM
Alright so Sin, Ninja Performance, RL7, and green-lantern all have a breather or crank vents. How are all of you routing them? I've seen maybe 5 different routing setups on the board and a couple of partial pics in the past few days. What's working for everyone? Pics or diagrams would be a big help and explanation as to why people are routing differently.
green-lantern
03-10-2011, 11:56 PM
Well mine was all vented to atmosphere and of course it didn't push oil out of turbo seals anymore but soon after I started having VSS leak. Some have problems with this and some don't.
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8749-1.jpg
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8751.jpg
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8753.jpg
Now I put the rest back to stock except for this. I installed krank vents so they would close under vac.
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8794.jpg
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8793.jpg
So far it has seemed to work out well this way except I still get a little bit of smoke when I 1st fire it up at idle. I'm going to put another valve in between the rear head and the bubble and see if the extra vacuum helps seal the VSS. The valve will add some more resistance when venting the engine under boost but it should be OK.
J. Fast
03-11-2011, 12:14 AM
So that's going to be 3 vents total? As for now you reverted to running the stock PCV on the front passenger side, one crank vent on the front drivers side, one crank vent on the rear drivers side and what for the passenger side rear? What made you use a "T" from the front to rear on the drivers side instead of just adding a vent, was it still smoking or does it need to be that way to equalize the pressure in the heads because the block is split due to it being a "V"?
green-lantern
03-11-2011, 01:49 AM
Yes 3 vents
I did have the hoses split on the drivers side that normally attach the heads together but I wanted to help equalize the pressure in the heads again. I have two hoses coming off of it because the krank vents are a big restriction so two hoses twice the venting. The rear passenger side goes straight to the bubble right now just like stock but a friend on here turned me on to some cheap valves that seem to be a good alternative to expensive krank vents so I'm going to try one in that hose to put more vacuum in the crank case. I'm hoping it doesn't cause too much of a restriction in that hose. I don't think it will though.
J. Fast
03-11-2011, 09:25 AM
Thanks man, pictures help a lot!
How are you venting IPO, the same way?
Rocket
03-11-2011, 09:57 AM
[QUOTE=green-lantern;74816] but a friend on here turned me on to some cheap valves that seem to be a good alternative to expensive krank vents [\QUOTE] Let me know how this goes.. I would be interested in a cheaper alternative to the kranks :)
green-lantern
03-11-2011, 12:47 PM
Will do, I ordered some extra ones to put through a torture test.
mb7050
03-11-2011, 02:29 PM
I´m not a fan of krank vents or venting(all ports) the crankcase because on a street engine, the proper PCV system keeps a clean air flow through the crankcase that removes the moisture, unburnt fuel, and corrosive combustion by-products.
soo a PCV system is not for only releiving crankcase pressure, its an important function, but it has an equally important function and that is to save your engine !
mb7050
03-11-2011, 09:51 PM
hmm
http://www.youtube.com/watch?v=wGrx2rvIxJ0
tempting : Moroso 25900 Moroso Crankcase Evacuation System (http://www.jegs.com/i/Moroso/710/25900/10002/-1)
J. Fast
03-13-2011, 02:41 PM
I was wondering when someone was going to bring up using a mechanical or an electric vac pump. Truth be known, that's probably the best solution when you're throwing a crapton of boost in there. Same as the old school valve cover to check valve w/exhaust tap... Most of the DSM guys I know use a secondary mech pump... but oh well.
J. Fast
03-13-2011, 02:44 PM
Looks exactly like this as a matter of fact :) ... Mitshubishi 4G63T Vacuum Pump Kit Galant, Eclipse, Eagle Talon, Plymouth Laser (http://www.gzmotorsports.com/4G63T-kit.html)
green-lantern
03-13-2011, 05:09 PM
Looks exactly like this as a matter of fact :) ... Mitshubishi 4G63T Vacuum Pump Kit Galant, Eclipse, Eagle Talon, Plymouth Laser (http://www.gzmotorsports.com/4G63T-kit.html)
That's a pretty good price. I was very interested in this before but if I remember correctly it was like 2 grand.
BTW there is a thread about it here.
J. Fast
03-13-2011, 06:19 PM
Is it in SMA or something? Haven't seen it. Got a link?
mb7050
03-13-2011, 07:53 PM
I was wondering when someone was going to bring up using a mechanical or an electric vac pump. Truth be known, that's probably the best solution when you're throwing a crapton of boost in there. Same as the old school valve cover to check valve w/exhaust tap... Most of the DSM guys I know use a secondary mech pump... but oh well.
in the video it shows how well exhaust slahs cut works and it should suck even more as the revs increases..
here is the linky i think ?
http://www.3sgto.org/f13/crankcase-ventilation-1042.html
but I´m a little sceptical about adding significant vacuum in there since my bmw recently had an engine failure because of too much vacuum in the crankcase (pcv system failure mechanical vacuum pump). it sucked oil from the bearings etc etc ..
and in stock form there is no vacuum just air circulation.
J. Fast
03-13-2011, 08:21 PM
Totally forgot about that thread, I will update there.
No info or pics on your setup IPO? That's cool...
mb7050
03-13-2011, 08:36 PM
he used electric vacuum pump...
Funny you should post this. My current setup (well the motor is pulled now) but the setup I did have, I would get lots of moisture in the motor. The underside of the oil cap would be milky from water until the motor ran a while with the pump and burned off and or pulled the moisture out. It may have contributed to the demise of the motor. I am going back to a PCV valve.
driver's side covers stock hose connecting them
Front pass side to sealed can
Sealed can to Vacuum pump
extra port on can to one way valve-seals on vacuum but if pressurized from crank pressure it opens and dumps air to atmosphere
rear pass side open filter.
in the end
what I did and it worked pretty well, I removed all 3 valve cover vents to sent them to a catch can. Left the one pass front to lower intake with a higher flow PCV valve in place. This gave me good vacuum to evacuate while under vacuum (no boost) but LOTS of breathing room to evacuate the crankcase under boost. All there lines are seperate, the driver's side does not loop from front to rear.
electronic PCV system? - Page 34 - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f42/electronic-pcv-system-255416/index34.html)
J. Fast
03-13-2011, 10:06 PM
Thanks man... I don't venture to that site, and I never will until David is gone. It's too bad, I'd love to have some tech discussions with some folks overthere but FTG and AF too!
KeithMac
03-14-2011, 05:23 PM
Every time I`ve read a thread where someone`s tried to use an electric pump it`s either not worked or burnt out.
Is it around 5hp worth to create a good vacuum?, works out at a pretty big current draw and electric motor to produce that consistantly.
Sin'sVr4
03-14-2011, 06:46 PM
well, i just ordered new valve cover and sprak plug gaskets. should be in friday. ($31 oem thru mits for all, front cover only) I dont know what setup I should do now? What should I do? I was going to run it like paul, but I only have 2 krank vents. small one is going on the hose that the pcv was. large one is going onto rear cover. Going to cap off lower intake plenum. I was going to "T" together the rear and front valve covers on the driver side and vent them to open atmospehere with a single line venting not dual like pauls.... What do you guys think?
green-lantern
03-14-2011, 06:51 PM
You can still run like mine is now. There are cheaper vents (much cheaper) that appear to be good.
Sin'sVr4
03-14-2011, 06:54 PM
paul, pm me or call me so you can tell me what cheaper versions and where i can get them and how much. Alos, why r you running 2 seperate line from driver side rear to front covers instead of 1?
green-lantern
03-14-2011, 07:08 PM
paul, pm me or call me so you can tell me what cheaper versions and where i can get them and how much. Alos, why r you running 2 seperate line from driver side rear to front covers instead of 1?
The krank vents are a pretty big restriction so using two doubles the ability to vent.
Edit: I'll give you a ring later.
Ninja Performance
03-14-2011, 10:39 PM
Totally forgot about that thread, I will update there.
No info or pics on your setup IPO? That's cool...
Sorry bout that, been crazy busy around here ;)
-Chris
I´m not a fan of krank vents or venting(all ports) the crankcase because on a street engine, the proper PCV system keeps a clean air flow through the crankcase that removes the moisture, unburnt fuel, and corrosive combustion by-products.
soo a PCV system is not for only releiving crankcase pressure, its an important function, but it has an equally important function and that is to save your engine !
Just want to make sure my last post wasn't misunderstood. When I said to run open breathers, it wasn't because it is superior to the stock setup. It just insures that you do not pressurize the crankcase in a very simple way. Pressurizing the crankcase is a very bad thing and needs to be corrected immediately.
For PCV systems, my opinion: vacuum pump > slashcut (although I've read some mixed things) > stock system with (properly installed) catch can > stock system > open breathers >>>>>>> broken stock system
For simplicity and robustness, you can't beat open breathers, it just doesn't work quite as well and isn't as environmentally friendly.
I run the stock system with a small home made catch can to keep the intake pipes cleaner. There is a picture of it in the pcv thread, but I have different valve covers, so it usually confuses people.
Ninja Performance
03-18-2011, 10:46 AM
When I am going to be running high boost (most of the time, and I mean 30-36psi) I run all 4 open and into catch cans. This is because I have not found a good working PCV system that also allows adequate crank case ventilation at 30-36psi boost pressures. Now, what this will do after warm up is allow the VSS to burn oil at idle at stop lights etc. The VSS in our cars need crank case vacuum to seal. So that kinda sux. But I can't setup a system to give me vacuum AND adequate volumes of ventilation at high boost.
I have a couple of the big Krank vents I may try something with. But even teh large ones pose a restriction. And the large Krank vent creates too large of a vacuum leak and raises the idle. Green Lantern..What you got?
A correct working PCV is nice. It pulls unburnt fuel vapor and moisture out of the pan area.
-Chris
mh3kgt
03-18-2011, 11:50 AM
I'm waiting to hear Paul's feedback on those cheaper krank vents as well. I have some, but haven't gotten to try them out yet. Car is all torn apart for an oil pump right now.
Sin'sVr4
03-18-2011, 12:26 PM
i just got my new valve cover gaskets so as soon as i put those in I am swapping my valve cover to the pcvless one and then gonna try a few diffrent things. I need to install my aem twinfire and change plugs. Im just hesitant to change anything because she is running perfect, not smoking at all or anything.
green-lantern
03-18-2011, 12:53 PM
Matt, I haven't got around to torturing one of those valves yet but I do have one on my car. I put one between the rear head and the bubble to try and get the VSS to stop leaking. It still leaks but not as bad. I'm starting to wonder if the machine shop didn't put them on right (VSS).
Chris, I was running all four vents to hoses under the car but then my VSS started leaking. They might of leaked a bit before and I just didn't notice but I'm pretty sure it popped up right after I did it. So to try and vent and get vacuum at idle I put the passenger side back to stock (PVC valve to intake and rear to bubble) then I kept the hoses on the drivers side but put krank vents in them to get some vacuum in the engine. I also connected the heads back together to help equalize the pressure in the heads. I kept both hoses instead of running one because the vents are such a restriction.
Like this
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8794.jpg
The VSS got a bit better but still leaked. Somebody brought up that the engine isn't under vacuum with the stock system because the rear hose to bubble just lets air in at will. I'm interested in what you have to say about this Chris because I don't know if the air rushing through the bubble puts a bit of a vacuum on the hose like hooking to the exhaust or not.
Anyway since the VSS was still leaking some I tried one of these valves in the hose to the bubble.
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8799.jpg
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8801.jpg
You can see the valve in the hose down there. Again the VSS got a bit better than before but it still leaks and now that I have valves on all of the hoses I'm right at that point of having too much of a restriction to let out pressure under hard pulls. So I plan to replace the VSS and probably take the valve out of the rear hose and see what happens. These heads are supposed to have new VSS in them so I want to investigate if they were done properly or not.
Sin'sVr4
03-18-2011, 01:06 PM
Paul, I think what I am going to do is basically, replace the current VC with the pcv, with my custom one, then just run no pcv with the krank vent to lower plenum, and then just keep the other krank vent from the rear vc on the line to open atmosphere.
If it aint broke dont fix it.
green-lantern
03-18-2011, 01:44 PM
Paul, I think what I am going to do is basically, replace the current VC with the pcv, with my custom one, then just run no pcv with the krank vent to lower plenum, and then just keep the other krank vent from the rear vc on the line to open atmosphere.
If it aint broke dont fix it.
Were you smoking after boost or did your turbo just let go all of a sudden? If it started smoking after a hard pull first then blew later then I would be a little worried about damaging a turbo again.
Sin'sVr4
03-18-2011, 02:31 PM
Were you smoking after boost or did your turbo just let go all of a sudden? If it started smoking after a hard pull first then blew later then I would be a little worried about damaging a turbo again.
it all of a sudden started one morning. just started pouring out. i was like wtf? that night i pulled the turbos. Then Brian at forced performance called me and told me that a piece of plastci is the reason the turbo went bad. blocked the oil supply. Never smoked before that.
Looked like a train when it first went. i was actually scared I blew up the motor. lol Just teh front turbo. The way I redid all the lines and gaskets on re-install I know I did everything perfect so no chance.
mh3kgt
03-18-2011, 03:51 PM
Paul, are you going to remove the heads to do VSS, or do it on the car? I'm half tempted to check mine out since the motor is apart right now anyway. I know the rear head VSS is brand new, and the front head has ~75k on it since I had to salvage it from my old motor, so it's possibly some of my smoking is from bad VSS on the front head, I hope to god the rear is still fine. Still have to rip off turbos to inspect them too I guess. I just don't want to put it all back together and have it still smoke on decel
Sin'sVr4
03-18-2011, 04:30 PM
sounds like your turbos buddy. decel means its pulling the oil past your bad seals/ and or bearings with the vaccum.
mh3kgt
03-18-2011, 04:45 PM
sounds like your turbos buddy. decel means its pulling the oil past your bad seals/ and or bearings with the vaccum.
Yeah that's what I was worried about. I had a leaky PCV valve that I didn't know about on this new motor, and I fear it took out my turbo seals, as well as cam seals, valve cover gaskets, and oil cap seal...I had absolutely 0 smoking on this build until recently, and it kept getting a little worse everytime I drove it. Did the ol' rattle test on PCV and it checked out, but I know it was bad since I did some more testing afterwards and found it leaked even by lung power alone. Did your car let out a slight puff if you revved it at idle Sin? I noticed mine smoke on decel, but then later noticed it would emit a slight puff at a stop if I revved it, and let it settle to idle again....sounds like I get to rebuild some 15g's eh. Very tempted to just drop the 1k to have my other 9b's converted to 19t, but will have to wait since I just got the wife a new R6 to ride to replace her 250r
I'm fairly certain one of the reasons Mitsubishi only put a pcv valve on one valve cover was to prevent crankcase pressurization in the event of a pcv failure. Krank vents eliminate this safety measure. The pcv system is constantly working as you drive. If the krank vents happen to stick at the wrong time it can pressurize the crankcase and cause something bad to happen. I don't think anyone should put krank vents on their car with the idea of benefiting from the vacuum they may provide. You are risking damage for little proven positive result. If boost is getting past a stock pcv valve, a "krank vent" placed between it and the manifold would probably help and that is the only place I would ever put something like this. The issue with replacing the pcv with a krank vent is that a krank vent acts more a check valve than a true pcv. This means that you will be imparting full manifold vacuum to the crankcase (and the fresh air inlet tube) at idle and part throttle. This will cause a lot of air to bypass the throttle body and should make for a pretty fishy idle and probably some other fun effects.
For true manifold vacuum, do it right and separate the system from the intake tract. I wish someone would try to use the a/c compressor just for the hell of it.
I think a vacuum is created in the stock pcv system under boost- as the pre-turbo intake is under some vacuum (depending on the amount of restriction) and the pcv should be closed. I think this is part of the source of the "normal" oil in the intake pipes.
mh3kgt
03-18-2011, 05:30 PM
Broken ring lands / fucked up rebuild / too much overbore?
Worn out turbos normally have oil all over the turbine wheel, dry compressors.
Steve
SERIOUSLY?? You simply just cannot make a post without mentioning broken ringlands can you? GTFO. The build is perfectly fine, my ringlands are fine, it was not too much overbore either. If anything the smoking is from faulty OEM equipment such as the PCV system, hmm maybe I should just run dual PCV valves and get rid of all my ricer shit and I could have a 5yr build with a barely running car. Fuck you and take your twin stock FPR's with you. I'm sick of seeing the same posts from you in every god damn thread. /rant
mh3kgt
03-18-2011, 06:23 PM
Click, Ignore, done. Whew should have done that a long time ago.
I put normal in quotes to imply that it is there on many of these cars, not necessarily that it should be there. That part of the post was mostly food for thought, I'm not 100% sure what causes the oil to show up so frequently. I suppose it could just as well be leaky pcvs or broken engines.
green-lantern
03-18-2011, 10:57 PM
it all of a sudden started one morning. just started pouring out. i was like wtf? that night i pulled the turbos. Then Brian at forced performance called me and told me that a piece of plastci is the reason the turbo went bad. blocked the oil supply. Never smoked before that.
Looked like a train when it first went. i was actually scared I blew up the motor. lol Just teh front turbo. The way I redid all the lines and gaskets on re-install I know I did everything perfect so no chance.
Well you might be fine then. You might just want to run it stock except for the KV instead of the stock PVC valve.
Paul, are you going to remove the heads to do VSS, or do it on the car? I'm half tempted to check mine out since the motor is apart right now anyway. I know the rear head VSS is brand new, and the front head has ~75k on it since I had to salvage it from my old motor, so it's possibly some of my smoking is from bad VSS on the front head, I hope to god the rear is still fine. Still have to rip off turbos to inspect them too I guess. I just don't want to put it all back together and have it still smoke on decel
Gatecrasher is sending me the stuff to do them on my car but I might pull them to do it. Seems like too much of a PITA to do them on the car.
sounds like your turbos buddy. decel means its pulling the oil past your bad seals/ and or bearings with the vaccum.
What do you mean vacuum? Pulling oil from where? Unless your talking about vacuum in the exhaust I don't know what you mean. If he is leaking from seals then it's pressure that's causing the problem. He can blow through the PCV valve so I'm sure it's pressurizing the engine. I hope his problems will be gone with a new OEM PCV valve.
Broken ring lands / fucked up rebuild / too much overbore?
Worn out turbos normally have oil all over the turbine wheel, dry compressors.
Steve
God Damn man! Really? We know what you think already. Unfortunately you don't realize that everybody knows your a damn idiot. It can be a blown tail light and you talk about fucked up ringlands. Not everybody here has ran their engine so hard they have "just 28 counts of knock" (the highest the ecu will read). Please Go The Fuck On! I should have put you on ignore but you have been a gold mine for comedic material for me.
OK, Let it be noted that Steve thinks every body in this thread has broken ringlands! I know his name because he signs every fucking post even though his screen name is steve. Kind of like lordwarlock signing his post as "lordwarlock classified mod". He even has/had classified mod above his screen name.
Where was I? Oh yeah, please don't post in this thread anymore. We know! Ringlands! Big bore and those rice parts.
Ninja Performance
03-19-2011, 09:26 AM
The VSS got a bit better but still leaked. Somebody brought up that the engine isn't under vacuum with the stock system because the rear hose to bubble just lets air in at will. I'm interested in what you have to say about this Chris because I don't know if the air rushing through the bubble puts a bit of a vacuum on the hose like hooking to the exhaust or not.
The rear passanger valve cover to INLET bubble does not negate a vacuum. it helps create it. The turbo INLET is sucking in air, which means it is sucking on that rear valve cover hose helping create vacuum along with the front PCV valve connected to the penum. And under boost the rear is an outlet to burn off vapors back into the engine.
-Chris
mb7050
03-19-2011, 10:46 AM
there is never any "significant" vacuum or pressure in the crankcase according to my pressure/vacuum gauge hooked to the crankcase (boost 15psi), all stock pcv system .
years back I noted just a little positive pressure in the cc when i ran up to + 20 psi, all stock pcv system.
Ninja Performance
03-19-2011, 10:55 AM
With krank vents the idle crankcase pressure is high enough that removing the oil fill cap requires force.
-Chris
mb7050
03-19-2011, 10:59 AM
Now I put the rest back to stock except for this. I installed krank vents so they would close under vac.
http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8794.jpg
I like green-lanterns setup but instead of running those lines open-to-atmosphere I would route them to dual exhaust slash cut.
Moroso 25900 Moroso Crankcase Evacuation System (http://www.jegs.com/i/Moroso/710/25900/10002/-1)
mb7050
03-19-2011, 11:02 AM
With krank vents the idle crankcase pressure is high enough that removing the oil fill cap requires force.
-Chris
with the krank vents at idle cc is under almost same vacuum as intake mani according to my gauge but under boost I noticed more positive pressure in the cc ..
with the krank vents the gauge is moving alot while driving mostly beetween ~~16 inches Hg and 0, under boost I noticed ~1 psi more positive pressure in the cc over stock pcv system (boost ~20psi). I removed krank vents shortly after .
with stock pcv system in place the gauge is reading flat 0 constantly sometimes I noticed ~1 psi pressure under max boost (boost ~20psi).
with stock pcv system in place the gauge is reading flat 0 constantly sometimes I noticed 0.2-0.5 psi pressure under max boost (boost ~15psi).
I dont like krank vents because you have less ventilation in there under intake vacuum conditions and less ventilation under boost .
green-lantern
03-19-2011, 01:33 PM
The rear passanger valve cover to INLET bubble does not negate a vacuum. it helps create it. The turbo INLET is sucking in air, which means it is sucking on that rear valve cover hose helping create vacuum along with the front PCV valve connected to the penum.
-Chris
OK, that's what I was thinking.
With krank vents installed it does seem to make removing the cap a bit harder and you can feel the air rushing in.
green-lantern
03-19-2011, 01:36 PM
I like green-lanterns setup but instead of running those lines open-to-atmosphere I would route them to dual exhaust slash cut.
Moroso 25900 Moroso Crankcase Evacuation System (http://www.jegs.com/i/Moroso/710/25900/10002/-1)
Thanks and I might get one of those kits. I wonder how well those valves work. They could be a good alternative to expensive krank vents. The whole kit is less than one KV.
mb7050
03-19-2011, 02:06 PM
Thanks and I might get one of those kits. I wonder how well those valves work. They could be a good alternative to expensive krank vents. The whole kit is less than one KV.
hmm. just for the heads up i got reply from moroso and they stated that these kits are not designed to work on full exhaust system they told me people running these with full exhaust have experienced no vacuum at all under high rpm. valves can be good tho..
Sin'sVr4
03-19-2011, 02:07 PM
Paul, i think for now Im gonna swap the VC's and just use my krank vent in place of the pcv for now.
green-lantern
03-19-2011, 02:14 PM
Paul, i think for now Im gonna swap the VC's and just use my krank vent in place of the pcv for now.
Sounds good, just keep an eye out for smoke when boosting. If you don't get any then....well, your good. :)
Ninja Performance
03-19-2011, 03:48 PM
with the krank vents at idle cc is under almost same vacuum as intake mani according to my gauge but under boost I noticed more positive pressure in the cc ..
with the krank vents the gauge is moving alot while driving mostly beetween ~~16 inches Hg and 0, under boost I noticed ~1 psi more positive pressure in the cc over stock pcv system (boost ~20psi). I removed krank vents shortly after .
with stock pcv system in place the gauge is reading flat 0 constantly sometimes I noticed ~1 psi pressure under max boost (boost ~20psi).
with stock pcv system in place the gauge is reading flat 0 constantly sometimes I noticed 0.2-0.5 psi pressure under max boost (boost ~15psi).
I dont like krank vents because you have less ventilation in there under intake vacuum conditions and less ventilation under boost .
I am with you. With a Krank Vents, ventilation under boost sucks. Which is why I run without them. Especially since I run 36psi.
-Chris
Sin'sVr4
03-19-2011, 04:51 PM
ya but your 2x the boost im at and the KV's arent restricting me like you as much.
green-lantern
03-19-2011, 06:05 PM
I am with you. With a Krank Vents, ventilation under boost sucks. Which is why I run without them. Especially since I run 36psi.
-Chris
With the front one it doesn't seem to hurt anything but yeah the rear one cuts the venting so it actually fucks up turbos. I wish I would have known that a few years ago. I screwed up my turbos at BRG because of that rear one. I think it was the year after you got marred.
Sin'sVr4
03-19-2011, 06:25 PM
so should i take off the one that runs from teh rear cover to the bubble? Granted I am blow thru and it goes to open atmosphere.
green-lantern
03-19-2011, 06:30 PM
so should i take off the one that runs from teh rear cover to the bubble? Granted I am blow thru and it goes to open atmosphere.
Do you have filters right on the turbos or do you have pre turbo pipes you can run it to? If I were you I'd find a place to run that rear one to without the valve then use that valve for a hose between the heads like I do but just one instead of two.
Sin'sVr4
03-19-2011, 06:46 PM
i have dejon blow thru twintakes. no hole drilled to run the rear valve cover hose to. I actually had it running into a pepsi can...yes i know...
green-lantern
03-19-2011, 07:12 PM
i have dejon blow thru twintakes. no hole drilled to run the rear valve cover hose to. I actually had it running into a pepsi can...yes i know...
hmmm, maybe a catch can with a breather/filter? idk
Maybe have a tube welded into your exhaust?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.