View Full Version : 18x9 +50 offset wheel
Gearheadvr4
03-08-2011, 05:25 PM
What would a 18x9 +50 offset wheel look like? Would that stick out a lot?
rez604
03-08-2011, 05:54 PM
my previous wheels i had 9" wide with 42mm offset with 255 tires all around. on the front it was like a mm or 2 from touching the strut tower on the inside. im sure +50 will touch tower. on the back there was plenty of space in the wheel well. front was flush, rear was sunk a few mm
you could use it but would have to use 235 tires, and clearance on the inside for the front would be extremely close.
Gearheadvr4
03-08-2011, 06:02 PM
Does a + 50 push the rim out or in? I thought it would push the rim out and stick out from the fenders.
I tried to read up on what offset meant but I'm more confused now than before.
JasonY
03-08-2011, 07:33 PM
+50mm will pull the wheel in. A 10mm spacer to give the wheels an effective +40mm offset will make them sit pretty much perfect on the car.
Jason
skater334
03-08-2011, 07:40 PM
Jojo's VR4 had a -9 offset in the back, with the extreme widebody look it was badass.
JasonY
03-08-2011, 07:59 PM
That has what relevance to anything mentioned in this thread?
-Jason
mh3kgt
03-08-2011, 08:02 PM
Oh come on Jason, he used the word "offset" that counts for something doesn't it :p
Does a + 50 push the rim out or in? I thought it would push the rim out and stick out from the fenders.
I tried to read up on what offerer meant but I'm more confused now than before.
negative offset = rubber patch moves outboard.
positive offset = rubber patch moves inboard.
stock 8.5's ran ~42mm offset. i've yet to hear of anyone successfully go wider with a higher offset. going wider with the same offset is pretty dicey as it is.
Gearheadvr4
03-08-2011, 10:07 PM
Would running a spacer to get close to stock cause any negative affects? Could I still take it to the track?
So you guys think a 18x9 +50 is possible? I'm desperately trying to find a Blitz Type 03 to replace the one that got hit a while back. I may have found a couple. These rims are ultra rare and I only have 3... :(
http://i429.photobucket.com/albums/qq12/gearheadvr4/b17476e2.jpg
http://img312.imageshack.us/img312/7358/pic000171ak7.jpg
skater334
03-08-2011, 10:56 PM
That has what relevance to anything mentioned in this thread?
-Jason
The fact that a negative offset sets the wheel further away from the wheel well.
Would running a spacer to get close to stock cause any negative affects? Could I still take it to the track?
So you guys think a 18x9 +50 is possible? I'm desperately trying to find a Blitz Type 03 to replace the one that got hit a while back. I may have found a couple. These rims are ultra rare and I only have 3... :(
http://i429.photobucket.com/albums/qq12/gearheadvr4/b17476e2.jpg
http://img312.imageshack.us/img312/7358/pic000171ak7.jpg
you need to run them in pairs. i would never run different offset wheels on the same axle. fwiw, i think rez and i were probably both referring to the FRONT perch. you can fit higher offsets in the rear, i believe. i would say your best bet is, if you have to use +50's, put a pair of them on the back and test-fit. if they don't fit past the strut, then you can always add a spacer. i would think that even if you DID need a spacer for the back, that 13mm would be sufficient--but don't hold me to that. the calculation i'm getting is that you'd end up with 14mm more inboard--without the spacer.
Gearheadvr4
03-09-2011, 08:23 AM
Ok, good advice. I did not plan to only run the oddball offset on one rim only. But I don't know what the negative effect would be if I did?
I may jump on that deal I found. These rims come up for sale rarely.
if you run dis-similar offset wheels in the back, the car might track a bit funny--and i'm guessing you'd see premature tire wear.
you're a bloody idiot if you tried it on the fronts.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.