PDA

View Full Version : 3KVT 1993 VR4 Dyno Pulls, GZP 16T's



Emilie@GZP
03-07-2011, 07:09 PM
So, we've had a long run here with Marc, but we're finally dialing it all in now.

We did a few pulls on Saturday night for him with his new GZP 16T turbos, but could not get past 12psi without breaking up. So, we are upgrading his ignition system, and will be re-dyno'ing it again later this week... hopefully to put down some nasty numbers!!!


Stock engine, FMIC kit, borla exhaust, stock MAS, with an emanage blue, 560cc injectors, etc. @12psi we made 322AWHP.

Enjoy :)


http://www.youtube.com/watch?v=Uus8AspXCEo

3KVT
03-07-2011, 07:11 PM
Christmas tree style FTW!!!

NOMIEZVR4
03-08-2011, 01:14 AM
hot looking VR-4..:)

rez604
03-08-2011, 01:38 AM
im liking the torque curve.

subscribing to see end result

AdamVR4
03-08-2011, 12:55 PM
You shouldn't need to upgrade anything in the ignition system to run 12+ psi. We're talking about 322 AWHP with a mid-grade TD04 ceiling. What on earth are you ugprading?

I have a stock ignition system other than MSD wires (which aren't necessary) and copper plugs @ .020-.022" and I've run up to nearly 33 psi cleanly. Trevor had a completely stock ignition (with regapped iridium plugs) system at basically the same levels.

Tighten the plug gap. If that doesn't work, replace the coil pack with new (or newer) OEM. If that doesn't work, suspect the PTU. Anything more is a waste of money.

Emilie@GZP
03-08-2011, 12:58 PM
I believe Hans found that one of the coils was bad/not great.

AdamVR4
03-08-2011, 01:01 PM
No surprise there. These cars are old. The ignition was one of the very few over designed systems on the car, haha... And unfortunately, people tend to upgrade it when they don't have to and often create more problems than they solve.

Emilie@GZP
03-08-2011, 01:08 PM
We had discussed with Marc possibly upgrading to the HKS DLI, but we all agreed we'd try swapping in a good stock one first to see if that solves the problem. He's been having this issue for quite a while now, so, the frustration with it was enough to want to replace everything and be done with it :lol:

3KVT
03-08-2011, 02:43 PM
haha, yeah, since fuckin '03 it's been doin this shit, and I never thought to check the coils. The new plugs and wires last spring helped out tremendously, but the coils are still factory and Hans said one of them had way higher resistance than a new factory set. Can't believe I never checked em before, but I'm still learning about these cars.

and the frustration did make me just want to say fuck it and get a whole new system, lol. Hopefully a new set of coils will clear her up and let her scream out 400awhp like she's supposed to.

MADMarc
03-27-2011, 02:42 PM
Were you ever able to get some new coils in there? How many miles are on the current ignition setup?

TurboSinceBirth
03-27-2011, 03:48 PM
I'm glad you guys didn't just throw an HKS DLI in there to see if it would have solved the problem because I already know it wouldn't have worked. 12 psi on 16Ts won't task the stock ignition system. Either the coils, plugs, plug gap, wires, or PTU needs to be checked. :)

Emilie@GZP
03-27-2011, 05:07 PM
Were you ever able to get some new coils in there? How many miles are on the current ignition setup?

We replaced the bad coil before he drove Tue car home a few weeks ago. It's been running well since then. It's actually back at the shop now for some follow up.

MADMarc
03-27-2011, 11:37 PM
I'm curious if the coils take care of the issue or if he will be snagging a new ptu as well. I'm kind've in the same boat over here...just swapped my coils a couple thousand ago and still get massive studdering and knock at higher boost levels...then again, I also have to fix a leaky intake hose. Hopefully the less expensive helps mitigate my problems but i'm interested to see how those 16t's do after the new packs.

Emilie@GZP
03-28-2011, 08:44 AM
We swapped the coil last time he was here (when this thread was posted) he has been driving it since then with no issues. He just dropped it back off for some follow up stuff.

3KVT
03-28-2011, 10:08 AM
Let me know when you get her back on the dyno!
It should be noted that I wasn't whoopin on it too much when I got it back, and that I turned the boost down to about 10psi. Had to take it easy, cause the trip home was 400+ miles one way. It did fine though, and I got the alignment taken care of, so it's really practically finished, just gotta get the rim touched up and dyno this bitch... again.

1993RT/TT
03-28-2011, 02:37 PM
subscribed and interested to see what 16Ts will do

Boomer3000
03-28-2011, 03:08 PM
Sub.. I am interested in the 16T's as well.

93SlugTT
03-28-2011, 03:09 PM
also wanna see numbers.

Ninja Performance
03-28-2011, 04:54 PM
No surprise there. These cars are old. The ignition was one of the very few over designed systems on the car, haha... And unfortunately, people tend to upgrade it when they don't have to and often create more problems than they solve.

What people forget. And then try to run over stock boost (or even stock boost) and then complain about how a 3S is crap...with thier 20 yr old 150K mile coils LOL

-Chris

SpdDmnVR4
03-28-2011, 05:03 PM
Im running 16T's at 11 psi on stock Injectors/stock tune. Interesting that you all made 322/315 on 12 psi with 560cc injectors (I must not be far behind). Those injectors have ALOT of headroom left as well.

Im planning on hitting ~400whp with just 450's and a SAFC. Im curious what the HP ceiling is on a proper running 16T car with the stock MAS in place. Are you planning on maxing this setup out? or just shooting for 400+ wheel?

Im considering going with an Evo 8 Maf conversion, but I dont suspect 400 wheel will outflow the stock MAS. It will be close however. I guess time will tell.

Emilie@GZP
03-28-2011, 05:46 PM
The same 16Ts, on a Spyder we built around the same time. 400AWHP @ 16psi on a nice safe tune.

Build thread here, with specs. http://www.3sgto.org/f2/gzp-16t-spyder-vr4-dyno-results-4122.html


http://www.youtube.com/watch?v=F2Jf4OA5X5s

3KVT
03-28-2011, 08:40 PM
Im running 16T's at 11 psi on stock Injectors/stock tune. Interesting that you all made 322/315 on 12 psi with 560cc injectors (I must not be far behind). Those injectors have ALOT of headroom left as well. Fo sho. I think IDC was like 65% or something, I'll let Hans correct me if I'm wrong. It was runnin pretty rich too, at 12 psi.

Im planning on hitting ~400whp with just 450's and a SAFC. Im curious what the HP ceiling is on a proper running 16T car with the stock MAS in place. Are you planning on maxing this setup out? or just shooting for 400+ wheel?

Im considering going with an Evo 8 Maf conversion, but I dont suspect 400 wheel will outflow the stock MAS. It will be close however. I guess time will tell.
Given the history of this particular car, I don't think maxin it out is an option at this point. 400awhp was what I had in mind when I started this whole project, so that's my target number right now. I'm hopin it can be as easy for my car as it was for the spider after the coil change, but I guess we'll just have to see. If Hans thinks it can do more without exploding, I may just have to see what it's capable of doin.

and I see you have a similar setup. any chances of you gettin some hard numbers in the near future?

SpdDmnVR4
03-29-2011, 01:07 AM
its doubtful... while I would love hard numbers, the closest Dyno is Automotion in Louisville (Its a mustang dyno, but it reads notoriously high. I wouldn't be surprised in the slightest bit if it said my car out down 375 whp right now and a stock vr4 puts down 290 whp. Yes that high!), next closest is IPS in Columbus. I would love to go to IPS, but if I do go there it will be for them to finalize my tune and probably won't happen until late July at best.

I plan on tuning myself using just an AEM wideband, HHH datalogger, 450cc injectors, AFPR, and an old school SAFC (I have these right now). Im hoping I can get away with 15 psi and make ~400 wheel on a decent self-tune. I mean your at 322 at 12 running rich. estimate at least 15 whp/psi increase(since we are well within the efficiency range of the 16T), thats roughly 370 wheel, fine tune the A/F ratio and pick up 15-20 wheel and thats ~390 whp. logically, Im not far from my goal, although I may run out of injector before I reach it.

Honestly, Im just going to do it and see what I can get. track times tell my story. Sooner or later Ill get on a dyno. My butt dyno says Im around 300 whp right now. Car pulls hard and clean. Now I just need to fix my slipping clutch issue and install all those lovely mods sitting on the shelf waiting patiently. Soon enough. Im only a college student....

93SlugTT
03-29-2011, 02:32 AM
Nobody seems to really really push 16ts or 15gs. Everyone does a mid ranged number like 16psi. I have seen that all over this forum.nobody pushes there turbos. Here I am, I'm going for 23psi on e85 in 15gs lol. I'm like a madman to come people on here. It seems this cword is more tame wiith pushing there turbos.

OBXBoost
03-29-2011, 08:04 AM
Nobody seems to really really push 16ts or 15gs. Everyone does a mid ranged number like 16psi. I have seen that all over this forum.nobody pushes there turbos. Here I am, I'm going for 23psi on e85 in 15gs lol. I'm like a madman to come people on here. It seems this cword is more tame wiith pushing there turbos.

We will see about that.

3KVT
03-29-2011, 09:57 AM
I'd like to push 'em, but we'll have to see how the car is acting first. As I said, given it's history, I don't know how safe it will be to push em too hard.

SpdDmnVR4
03-29-2011, 01:06 PM
Nobody seems to really really push 16ts or 15gs. Everyone does a mid ranged number like 16psi. I have seen that all over this forum.nobody pushes there turbos. Here I am, I'm going for 23psi on e85 in 15gs lol. I'm like a madman to come people on here. It seems this cword is more tame wiith pushing there turbos.

This isn't a fair comparison. I would love to push my car, eventually I will, but for now Im a college student, paying my own way. I use the VR4 as a DD, and its always been a good car. That being said, modding the VR4 is a lot of fun and Usually very rewarding, but its just not feasible right now to come out swinging for a maxxed out setup when I have stock long block in the car (albeit its a healthy engine, but it is a 1st gen cast crank car).

Also, to really take advantage of 16T's you are probably going to need a FMIC ($600 I dont have), and honestly Blow thru is the best way to go IMO ($400-800 depending on new/used and all the piping/mas you decide on. Again, Not in my budget). I have considered going with an Evo8 Maf, as I said before, since others have had fairly good results. Plus its much less expensive than blow thru but still better than stock. Then to support that extra power at the track (or even on the street) you need a semi upgraded drivetrain, (Output shaft at least.. which is like $350-400 I believe). You can see that going past 400whp or "maxxing out a given turbo" can take alot of money and severely hurt reliability.

The reason you don't see alot of maxxed out 15g/16t setups is because those cars are built with goals in mind. (Like mine for instance is to run 11.99 @ 115+ and still DD my car.) If you wanted to go balls to the wall and max out a power setup, you go for the big turbo's (TD04 anyway) like 19T's, DR700/750's, Billet or not. Those are the turbos that make the big power easier. Its not that 16T's can't make power, Its that larger turbos make power easier.

Anyways, /rant

93SlugTT
04-02-2011, 01:36 AM
I'm not going to clutter this thread with how nobody pushes 15th and 16's.

Back on topic, where's the update? How is the car coming, what is the plan with these turbos , do u plan on pushing them as far as you can

3KVT
04-07-2011, 09:49 AM
There is still no update, as my car apparently got pushed to the back burner yet again. I haven't heard anything from Hans since last week, and he told me they were going to try to dyno saturday.
As far as the plan goes, there really isn't one. I want to wait and see how the car acts under the higher boost levels (once we get the ignition system stuff figured out). I'm really only concerned with hitting 400 as of right now, though.

Emilie@GZP
04-07-2011, 10:00 AM
We dyno on saturdays. So, we're hoping to get it on there this saturday. It really depends on how long the other 2 cars take on there.

3KVT
04-07-2011, 10:21 AM
We dyno on saturdays. So, we're hoping to get it on there this saturday. It really depends on how long the other 2 cars take on there.

works for me.

vr3.9
04-07-2011, 10:31 AM
I'm not going to clutter this thread with how nobody pushes 15th and 16's.

Back on topic, where's the update? How is the car coming, what is the plan with these turbos , do u plan on pushing them as far as you can

Since they won't dyno till Saturday might as well clutter a little.:biggrin: If he can get 400 on pump gas and stock MAF, I would call that pushing it. That being said I think some of the old 15g and 13T records need to be broken. Once I can switch to blow thru I plan on spending a little time on the dyno and go for it again. After I break it :Clap:. I will most likely throw my 550's back in and shoot for around 400 on pump, again that will be pushing it.

SpdDmnVR4
04-07-2011, 03:39 PM
VR3.9, What was your mod when you ran your best 1/4 mile? Also Are you using Timing control? I ask because 780's are BIG and I dont see how you could get away with them without timing control

and I am sure that the stock MAS is a huge restriction but others have made high 300's/low 400's in power on it, why can't this car?

vr3.9
04-07-2011, 05:01 PM
That 12.33 was with 550's and stock Maf. 780's are definitely too big for 93, I've turned the fuel pressure down to about 36 and still won't run more than wastegate on it. They are however a little small for E85. Was limited to the 471 because my injectors were giving it all they had. I'll turn up the Fuel pressure to 55 and give it another shot. That will also give more timing, fuel pressure (injector size) is the only timing control I have.

SpdDmnVR4
04-07-2011, 05:29 PM
I didn't realize that you were running E85. I was wondering why your injectors were so big. Its interesting that you have no timing control at all (besides tuning using FP), does that seem to work pretty well with the 550's? or do you wish you had timing control?

For simplicities sake, I plan on running just an SAFC, 450's, and a AFPR. I want a two dimensional tuning map to work with. Adding 3 dimensions (boost, fuel, and timing), I fear would make self tuning my car too complicated. Especially considering this is my first time. Perhaps in the future I will change my mind. Im hoping that with 450's and cranked fuel pressure I can get my car near your 12.33 run. I really just want a super fun DD, tuning doesn't scare me, but I want to keep it simple and still pick up a decent amount of horsepower. Would you consider your car a fun street car when you had the 550's and stock MAS installed?

I am beginning to think that perhaps 450's will be a bit small for the power I would like to make, but then again I am relying on a "butt dyno" to tell me how my car is running. right now my car will pull 105 trapping cars on the street (from a roll) but my best 1/4 mile is a 13.5 @ 102 ( with my clutch slipping on the launch and between shifts).

Simace
04-08-2011, 06:49 PM
Hans said one of them had way higher resistance than a new factory set...

Quick question on this ^

According to Stealth316, the Primary Coil Resistance is between 0.67-0.81 ohms, while the Secondary Coil Resistance is between 11,300-15,300 ohms

When you mention that Hans says it had "way higher resistance"; does that mean that if the resistance is closer to the high-end of the factory specifications (0.81 on Pri, 15,300 on Sec) and not going past, that this in itself might be a good enough reason to change out the coilpacks?

The reason I ask is because I recently, having the same issue as your car, got another coilpack (with all 3 coils) and tested it. This new (to me) coilpack registers closer to the lower-end of the factory specifications while the coilpack (in my car) is registering closer to the high-end (but not going over) of the factory specifications.

FWIW: I've already replaced the PTU with a brand new OEM (120.00) one and the hesitation/breakup is still there. Any higher than 14psi = hesitation/breakup. Mods in my sig.

Hym3n
04-09-2011, 12:42 AM
If I may, what (specifically) was required to install the 16T's? Did the front motor mount bracket require modification (a la some 13T setups)? Did water lines need to be modified? ANYTHING else?

Thanks!
Brian

Hym3n
04-09-2011, 12:43 AM
If I may, what (specifically) was required to install the 16T's? Did the front motor mount bracket require modification (a la some 13T setups)? Did water lines need to be modified? ANYTHING else?

Thanks!
Brian

SpdDmnVR4
04-09-2011, 03:24 AM
my 16t's, Which came from 3sx, required no modification to work. I actually put them on without pulling engine. Everything bolted right up with no modification needed. It was exactly like installing 9B's. But I can't comment on GZP's 16t's

Ninja Performance
04-09-2011, 08:10 AM
Most likely they are all the same, they may even be getting them from the same place.

-Chris

3KVT
04-09-2011, 09:22 AM
I'm fairly certain that no extra modifications were necessary. It's the same TD04 housing and I'm still using all my factory manifolds/piping (minus the FMIC).

Emilie@GZP
04-09-2011, 09:49 AM
It is a 13g housing. It requires no additional modifications to install, just bolts right up.

Hym3n
04-09-2011, 11:05 PM
Would it be safe to say that the 16T > 13T? Any specs comparing the two wheels?

Emilie@GZP
04-09-2011, 11:11 PM
They produce very close numbers.

93SlugTT
04-10-2011, 05:31 PM
Since they won't dyno till Saturday might as well clutter a little.:biggrin: If he can get 400 on pump gas and stock MAF, I would call that pushing it. That being said I think some of the old 15g and 13T records need to be broken. Once I can switch to blow thru I plan on spending a little time on the dyno and go for it again. After I break it :Clap:. I will most likely throw my 550's back in and shoot for around 400 on pump, again that will be pushing it.

i don't know what the record is but im shooting for over 500. also on e85, blow though, 15gs, aem ems, wisco's pistons, arp main,rod, and head bolts. pretty much every bolt on, fmic, 750cc. dual walbro pumps. if i need to push a bigg injector i will, hoping to hold 23psi if they will do it.

3KVT
04-21-2011, 05:00 PM
still waiting for dyno time cause Hans is paintin flames on his Ram

3KVT
05-24-2011, 11:01 AM
Welp, got the ignition issue resolved. Apparently the new coil did the trick. Still only did like 320+awhp, so we're gonna swap the stock MAS for a blow-thru and see if we can get better numbers today.

Emilie@GZP
05-24-2011, 11:03 AM
Welp, got the ignition issue resolved. Apparently the new coil did the trick. Still only did like 320+awhp, so we're gonna swap the stock MAS for a blow-thru and see if we can get better numbers today.

:7Up:

3KVT
05-24-2011, 11:17 AM
I'm giddier than a school girl.

Amphiron
05-24-2011, 09:18 PM
How did it go?

Emilie@GZP
05-24-2011, 09:24 PM
I didn't get back from picking up the parts until almost 6pm, so we will finish the install and dyno tomorrow.

3KVT
05-24-2011, 09:53 PM
The giddiness is on hold.

Toni
05-25-2011, 11:43 AM
Welp, got the ignition issue resolved. Apparently the new coil did the trick. Still only did like 320+awhp, so we're gonna swap the stock MAS for a blow-thru and see if we can get better numbers today.

How much boost were you running and what target afrs?

Hans@GZP
05-25-2011, 04:54 PM
How much boost were you running and what target afrs?

It was 1.06 kPa with 11.3 afr

The blow thru setup is almost done and I will have some numbers tonight.

Hans@GZP
05-25-2011, 04:55 PM
Oh, and I can't wait to see what difference in power the maft version 2 has versus the stock maf. I don't recall seeing back to back numbers on any power gains between the 2.

Emilie@GZP
05-25-2011, 07:45 PM
Fired back up... gonna be running it again soon. I'll post some back-to-back videos from the pulls yesterday with the Stock MAF with the dyno charts, and the pulls today with the maft version 2 video and charts. I'm curious to see these results :)

FastOldGuy
05-25-2011, 11:43 PM
I'm interested to see how it does. My car has just been up graded to 16T's and a FMIC I should be having it dynoed in a couple of weeks. I'd like >400hp on pump gas.

Hans@GZP
05-25-2011, 11:48 PM
We made 360 with stock intake pipes and 15 psi. Other cars with these turbos and metal intake pipes have made 400 at 16 psi. If I could get more boost without knocking, we would be well above 400. We can run more than 16 psi on the street without knock, but not on the dyno.

3KVT
05-25-2011, 11:53 PM
So I can turn it up a bit on the street?

Here's the link to the other thread about this car and the stock MAS vs. the 3.5" blow-thru
http://www.3sgto.org/f2/dyno-results-stock-mas-vs-maft-version-2-a-5100.html

Hans@GZP
05-26-2011, 12:00 AM
It's running around 16 psi on the street right now on your 3rd boost setting. I'm not sure what the 4th is set for lol.

FastOldGuy
05-26-2011, 12:03 AM
Are you using 93 octane?

3KVT
05-26-2011, 12:06 AM
I don't think I've set the 4th one. The first one is low and the second is around 1 bar, at least the last time I was in it, it was. haha

3KVT
05-26-2011, 12:06 AM
yeah, regular 93 octane pump

Hans@GZP
05-26-2011, 12:07 AM
Lane, yea. 93 octane.

Mark, I changed the first 2 settings. They are .8 bar and .95 bar.

FastOldGuy
05-26-2011, 12:22 AM
Does anyone know what the hp record for 16T on race gas?

Hans@GZP
05-26-2011, 08:49 AM
I'm not sure. I would expect around 500.

mannavr4
05-26-2011, 02:01 PM
I got 529awhp on 91+meth. I don't know if that's a record.

Sent from my HTC Dream using Tapatalk

3KVT
05-26-2011, 02:57 PM
Big thank yous to GZP, Hans, Em, and the rest of the crew! Super stoked and pleased with the results. Car runs magnificently, and makes me smile every start-up. Feels so good to drive this beast.

Emilie@GZP
05-26-2011, 03:17 PM
:7Up: Glad you're enjoying it finally!! :)