View Full Version : This MAY be my first n00b Question...
Nihil
03-05-2011, 02:48 AM
I'm kinda buzzed, but I've been wondering this for the past couple days now, I see a lot of subie guys (subaru) around here (that's the performance car of choice in my area) with lowered cars, look nice, rims flush with the fenders, with about 1/4 inch of clearance...
I know Terry's car (maximal peformance) is pretty slammed and a few others here are too...but not seeing them in person....
My question is, with that little of clearance, what happens if you bottom out, won't you hit the fender and fuck shit up? Or are those with setups like that, the douches who roll about 1.5MPH over any little bump in the road, in a daily driver?
J_Parker
03-05-2011, 03:04 AM
Lol, if you're only buzzed you're not doing a good enough job of drinking!
To answer your question though, if you plow a big speed bump or pothole... Yes it will fuck shit up on a quantum scale, I slammed my old Talon a while back and nailed a pothole doing about 60km/h and crumpled/dented in my rocker panel/fender pretty badly upon exiting it.
Mike-92RT
03-05-2011, 04:15 AM
lol i've done enough drinking to laugh out loud this LOL. Sorry.
Nihil
03-05-2011, 04:20 AM
SHH! I willl DRINK YOU UNDER THE TABLE! haha
I'm kinda buzzed, but I've been wondering this for the past couple days now, I see a lot of subie guys (subaru) around here (that's the performance car of choice in my area) with lowered cars, look nice, rims flush with the fenders, with about 1/4 inch of clearance...
I know Terry's car (maximal peformance) is pretty slammed and a few others here are too...but not seeing them in person....
My question is, with that little of clearance, what happens if you bottom out, won't you hit the fender and fuck shit up? Or are those with setups like that, the douches who roll about 1.5MPH over any little bump in the road, in a daily driver?
depends on your setup. i found out with my 285's that i wasn't bottoming out; i was scoring the tires on the fenders. needless to say, i got coilovers to RAISE the rear.
imho, the less clearance you have, the stiffer your ride must be. since my personal preference is for smooth; my best option is trying to find some type of fender flares or widebody to try and "close" the gap.
speedy25
03-05-2011, 10:18 AM
If you're going to race the car then the mods make sense. Doing it to a daily driver is insane since it badly affects ride quality just so you van look "cool."
-SP
green-lantern
03-05-2011, 12:31 PM
Slammed 3ses just don't look that good. The fenders are very wide so the lower the car is, the bigger the gaps on the sides appear. So the gap on top of the wheel you can get rid of by lowering the car but the gaps on the sides of the tires you can't really do anything about.
Slammed 3ses just don't look that good. The fenders are very wide so the lower the car is, the bigger the gaps on the sides appear. So the gap on top of the wheel you can get rid of by lowering the car but the gaps on the sides of the tires you can't really do anything about.
this^eleventy billion.
KeithMac
03-05-2011, 02:55 PM
As has been said, the lower you go the less travel the suspension has requing stiffer springs and harder damping.
On a normal road a car that`s too stiff will have problems keeping up with a car that`s go compliant suspension.
I took coilovers off mine and went back to stock ECS suspension, best mod I`ve done to the car regarding drivability..
Nihil
03-05-2011, 03:00 PM
Slammed 3ses just don't look that good. The fenders are very wide so the lower the car is, the bigger the gaps on the sides appear. So the gap on top of the wheel you can get rid of by lowering the car but the gaps on the sides of the tires you can't really do anything about.
Definitely agree, I don't know why they made our wheel wells so weirdly shaped, oddly enough, no one has made anything to fix it with aftermarket side skirts, fenders and bumpers...
depends on your setup. i found out with my 285's that i wasn't bottoming out; i was scoring the tires on the fenders. needless to say, i got coilovers to RAISE the rear.
imho, the less clearance you have, the stiffer your ride must be. since my personal preference is for smooth; my best option is trying to find some type of fender flares or widebody to try and "close" the gap.
285s? What rims? I've been lookin into rims for the TT and want to go as wide as possible without sticking out, flush is ok, as long as nothin gets torn up, that's why I asked this question, since I see a lot of cars runnin flush rims that are pretty lowered
DuTTch
03-05-2011, 03:25 PM
Hella flush
i've never seen anyone run 285's on all four and make it flush.
mine stick out; but unlike the majority, i actually like the look of having a couple inches of rubber sticking out.
green-lantern
03-05-2011, 05:39 PM
Definitely agree, I don't know why they made our wheel wells so weirdly shaped, oddly enough, no one has made anything to fix it with aftermarket side skirts, fenders and bumpers...
Yeah I'm a bit surprised nobody has messed with the fender holes, seems like it would be an interesting thing to photo shop.
i've never seen anyone run 285's on all four and make it flush.
mine stick out; but unlike the majority, i actually like the look of having a couple inches of rubber sticking out.
I like a little bit sticking out. The saleen replicas I have now seem to be about perfect for what I like.
Yeah I'm a bit surprised nobody has messed with the fender holes, seems like it would be an interesting thing to photo shop.
that's precisely my gripe with what offerings currently exist. equally narrow the gap on all sides; and do it in a way which looks stock; NOT tacked on or an afterthought. it's especially noticeable on the back, where such a piece would have to start at the "hip" rather than the wheel arch.
DocHoliday
03-05-2011, 09:27 PM
Yeah I'm a bit surprised nobody has messed with the fender holes, seems like it would be an interesting thing to photo shop.
Here's my take on it:
http://img69.imageshack.us/img69/2899/moddaysig.jpg
J_Parker
03-05-2011, 10:24 PM
I like the agressive change the most. I think if you were to get a widebody kit like Cianci's and some sideskirts to match you'd have a fairly OEM look going on. But you'd have to customize the bumpers to make it work... Maybe this'll be my next project when the car is inside...
green-lantern
03-05-2011, 11:15 PM
Here's my take on it:
http://img69.imageshack.us/img69/2899/moddaysig.jpg
I like it BUT the aggressive change curves in at the bottom and I don't like that. The slight change with wide body fenders could look really good.
Edit: on 2nd thought the aggressive change isn't all that bad. Maybe in between the two.
GTOJOE
03-05-2011, 11:18 PM
I like the agressive change the most. I think if you were to get a widebody kit like Cianci's and some sideskirts to match you'd have a fairly OEM look going on. But you'd have to customize the bumpers to make it work... Maybe this'll be my next project when the car is inside...
You know I just saw the pic and thought I just know this will be Jordan's next project. Then Bam next post hahaha
J_Parker
03-06-2011, 12:59 AM
You know I just saw the pic and thought I just know this will be Jordan's next project. Then Bam next post hahaha
Lmao, well what can I say, either you know me too well, or I just have to take advantage of a good idea when it comes along :p
J_Parker
03-06-2011, 03:51 AM
Just an idea to spitball here, how tough do you guys think it'd be to increase the track width by about 8" on our cars, if doable I'd most certainly try.
Just an idea to spitball here, how tough do you guys think it'd be to increase the track width by about 8" on our cars, if doable I'd most certainly try.
i suggest you research the threads about what was done to the PUMA gto.
Nihil
03-06-2011, 01:20 PM
Just an idea to spitball here, how tough do you guys think it'd be to increase the track width by about 8" on our cars, if doable I'd most certainly try.
Anything's do-able man! The biggest thing to consider when goin wider like that though are your stress and leverage points/weight distributions on the axle and components since you're moving the wheels away from their center of gravity.
I don't think we really need to go that much wider, with our cars, they're already pretty nice, just a couple inches to enable us to tuck some wide tires under is all we really need. Have you seen that red car from Japan?
http://img.photobucket.com/albums/v229/prevailingevils/Stealth3000gt/Jap%20Widebody/11.jpg
http://img.photobucket.com/albums/v229/prevailingevils/Stealth3000gt/Jap%20Widebody/05.jpg
http://img.photobucket.com/albums/v229/prevailingevils/Stealth3000gt/Jap%20Widebody/10.jpg
By far my most favorite 3S, I have more pics on my comp I can upload to photobucket and share with everyone! ha
not japan, thailand. and as high-quality as the work on that car is, it completely destroys the look of the car. a body kit should compliment the stock lines/design; not reinvent it. if you don't like the design of the car in the first place; then don't buy the car.
J_Parker
03-06-2011, 06:37 PM
not japan, thailand. and as high-quality as the work on that car is, it completely destroys the look of the car. a body kit should compliment the stock lines/design; not reinvent it. if you don't like the design of the car in the first place; then don't buy the car.
Precisely my thoughts, I would keep the lines of the car, just simply widen it. However... I HATE the look of just increasing the width of whe wheel wells, I would much rather see a kit that compleatly widens the car, doors and all, but keeping the origional look, perhaps making some of the air dams functional and a little more dramatc would be nice though. Also if I were to do something like it I would make a center garnish that widens the tail lights rather than the os so common retarded look of squaring the body work off when you reach them, the headlights are another thing to be widened with that big of an increase.
Nihil
03-07-2011, 12:21 PM
Aside from personal tastes, the guy did a great job of fitting the wheel wells around the wheels, I think. I posted those pics just so you could see that part of the car
J_Parker
03-07-2011, 04:15 PM
Sorry man, I wasn't trying to say he didn't do a good job, there's just things I would've done different. The onlt problems with the way he did his wheel wells is that he can literally no longer drive on unlevel road, unless he's got some serious sway bars, or retaining straps on his suspention. I can see that going very wrong for the average guy.
Aside from personal tastes, the guy did a great job of fitting the wheel wells around the wheels, I think. I posted those pics just so you could see that part of the car
it "looks" nice, but i wouldn't want something that extreme on my car. imho, the sides should never go past vertical. you start to create too many problems when you enclose the bottoms of the wheels; one of note is driving the car in snow.
if you look at a lot of other sports cars, they don't require flares to fit wider tires. this is because the top portion of the wheel well is actually flared out significantly wider than the rest of the well--STOCK. look at 99-04 mustangs. look at 93-02 camaros. if you look at both cars from the rear, even the narrowest "stock base model wheels" fit because they come approximately flush with the bottom of the well. significantly wider tires can be fitted and still look good because they will fit flusher with the top of the well. i think this is a good approach to be considered. this kind of "inverse taper" (wider at the top, narrower at the bottom) works well if the transition is smooth. and, because it allows for wider tires to fit with at least part of the well, it's kind of a best of all worlds solution. it's flush up top, but there's still plenty of rubber showing; which is, imho, one of the most aggressive things that can be done.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.