PDA

View Full Version : power steering question



92EuroDiamante
01-08-2011, 04:59 PM
Hey everyone,
so after a week of really productive work, I go for a test drive and my car dumps PS fluid and I lose power steering. No problem I think, I will cut out the leak and replace the pipe. Well the leak is on the tube right where it connects to the rack, right at the end so no cutting it out.

Its freezing here so I dont feel like replacing the whole line so I was thinkng about doing this, let me know if it would be a problem in a PS system. I was going to get the replacement tube, cut the last few inches off the new one, cut off the last few inches of the old one and then connect it to the existing tube with high psi tubing. The rest of my tubing has absolutely no corrosion so im thinking this is a quicker alternative to replacing everything in this weather.

I have done this with A/C lines after repairing older cars in accidents and its always worked well.

Thanks for any advice :)

DocWalt
01-08-2011, 05:34 PM
Kind of ghetto, but I see no reason why it wouldn't work.

92EuroDiamante
01-09-2011, 02:34 AM
Definitely ghetto haha. Thing is I would love to just throw a new rack in and then have every major component new/rebuilt on the car but the thing is I just put in coilovers and I would like to get more than 5 miles on my new alignment and balance before it had to be all undone haha.

RL7
01-09-2011, 06:05 PM
I think that may be the high pressure side that sees several thousand psi. I think the hose there would almost have to be metal. If it's on the low side, no problem. Pump->rack= high, everywhere else is low I think.

FluffyCow
01-10-2011, 12:24 AM
In theory, as long as you weld/solder/braze the tubing together(metal to metal, with a flaring/swaging tool like this (http://www.stridetool.com/tools/flaring_swagingtools/flaringtools_08.html)), it should work fine.

92EuroDiamante
01-10-2011, 11:18 AM
Kind of ghetto, but I see no reason why it wouldn't work.
My local Mitsu dealer is actually able to get me the correct one for very cheap in a reasonable amount of time (didnt expect that!) so I am leaning toward replacing the line.
Docwalt, I know you had a write up about removing the rack, do you remember how much you have to pull off to get to the line? Trying to determine if its better to replace the whole thing or permanently reconnect the last few inches of the new unit to the old one.

DocWalt
01-10-2011, 12:25 PM
Which line are you replacing?

92EuroDiamante
01-10-2011, 12:43 PM
Facing the car head on (looking at the headlights) it is the one that goes to the port farthest right I believe. Is one harder than the other, let me know, I will get a chance to confirm which one tonight or tomorrow. Thank you so much for the advice and help

DocWalt
01-10-2011, 12:52 PM
From what I remember, one of those two lines goes almost directly into a rubber line and would be somewhat easier to replace. The other line was a hardline for a much longer distance, I think. It's been two years, so I'm not 100% sure. :sad: I'm pretty sure the line going to the right is the low pressure line, and feeds into a rubber line to move up along the frame towards the P/S fluid reservoir. I don't have a service manual handy at work anymore, so I can't check to be certain.

92EuroDiamante
01-10-2011, 02:25 PM
Fairly certain it is the reservoir line now that I think about it because if I fill the reservoir it will begin to leak before I turn the car on and also it drips not sprays. If it is indeed at 1k+ psi Im gonna guess it would spray like crazy with a leak that size. I know radiators do!

Thank you for the help, just trying to gauge on weather its gonna be a simple job or a removing a dozen other things to do a simple job kind of thing, before I go and freeze!

DocWalt
01-10-2011, 04:37 PM
I unbolted the throttle cable from the plenum and firewall and also pulled the cruise control box off its mount and swung it back onto the cowl to gain access to those lines. Shouldn't be too bad. You may need to remove that subframe crossmember, or downpipe to have access from underneath, I don't know, I already had those two off. Good luck :)

92EuroDiamante
01-11-2011, 03:06 PM
You may need to remove that subframe crossmember, or downpipe to have access from underneath, I don't know, I already had those two off. Good luck :)

CRAP! I got a good look at it today and made a diagram. The view is from on your back underneath the car. feet sticking out from the front.
http://i53.tinypic.com/15z447p.jpg
There is no bolt to undo to the leak unless the line goes through that bracket (which if it does everythings gotta come out or it will have to be resealed once ran through). Looks like the best bet is gonna be to braze it or something, or remove everything and replace it all. Anyone in the Chicago area know anyone that can do that for me? When I have it jacked up as much as I can its still inches from my face and im not gonna play with fire there :p. Hopefully I can get it brazed and them im gonna put some sort of high heat coating over the rest of the lines to resist corrosion any further.

Also, does anyone know if the line that has a leak is one piece from reservoir to nut or if it is two pieces seperated by that bracket after the leak?
If its one piece Im thinking about just borrowing a lift, cutting out the straight section with a leak, feeding a new one through the bracket and reattaching it on each side.

CoreyB
01-11-2011, 04:32 PM
Done it with compression fittings many times. Never had an issue.

To be more clear I have bought new line with the correct end on it and used it to replace the bad line, then ran it until there was a good solid part of the old line and use the compression fitting to connect the old and new lines together.

92EuroDiamante
01-11-2011, 04:44 PM
Yeah, if only I had a half inch of room on either side of the hole. Its literally right up against that bracket.
Do you know what end fitting it uses? I ask because it would take mitsu quite some time to get me one and Id like this done by the end of the week.

DocWalt
01-11-2011, 04:50 PM
That line isn't that bad to remove, from what I remember. Obviously, that right side bracket needs removed, but meh :p

92EuroDiamante
01-11-2011, 05:11 PM
well thank god for bolt extractors. looks like ill be tearing it apart now that I know that line is one piece and not connected under the bracket. I found a hydraulics shop that says they can make me a set that wont corrode

92EuroDiamante
01-12-2011, 04:34 PM
Got the old lines out today, didnt take too long :)
Another thing for any IL guys. I had Bristol Hydraulics in Northlake make me a new set. They are wayyy beefier than the stock ones you can bend with your hand. All for only 80 bucks!

92EuroDiamante
01-12-2011, 09:03 PM
Got the new lines in and everything is working great :)
Thank you everyone for your help. Was much much easier than it appeared to be.

DocWalt
01-12-2011, 11:01 PM
Glad it went well for you!