PDA

View Full Version : Corbeau Seat Installations anyone having/had my problems?



MR2
12-25-2010, 08:01 PM
Corbeau Seat Rails + Brackets*-*Mitsubishi 3000GT*/*Dodge Stealth Parts (http://www.3sx.com/store/comersus_viewItemBundle.asp?idProduct=25297)

Anyone had any problems mounting these seat Rails? the tabs that you bolt through don't line up and the inner seatbelt side actually appears to need to be shimmed up!!

anyone?

Unknownvr4
12-25-2010, 11:40 PM
I modified a 1g dsm rail to fit in my car

MR2
12-26-2010, 12:27 AM
yeahh with much stuffing around I've made them fit :| funny enough they are only just able to move forward enough for my feet to fit on the pedals :p

looks like alot of people have the same problems doing a fair amount of digging around google. :|

KeithMac
12-26-2010, 06:53 AM
Most people have to ream the bolt holes out by all accounts.

FlamboyantStealthTT
12-26-2010, 01:31 PM
yeahh with much stuffing around I've made them fit :| funny enough they are only just able to move forward enough for my feet to fit on the pedals :p

looks like alot of people have the same problems doing a fair amount of digging around google. :|
im looking at the fx1 pro right now and thinking about getting it. how tall are you? im 5'8 and if my feet dont reach the pedals ill be pissed... also to fit the rails drill out the holes to be bigger??? thats all it needs to fit?

MR2
12-28-2010, 08:14 AM
I'm what...175cm? and yeah just had to drill the holes AND the rear rail does not sit on the holes level so I had to shim it up to make it level (the rear bolt tunnel side on both sides was over 1" lower than where the mount was attempting to attach to.

I think I'm also going to put another metal bar on the rails so I can have the seat further forward normally AND so I can lift the front of the seat up.

i3igpete
03-01-2011, 05:07 PM
i used to have the FX1's. do NOT use the bottom mounts, use side mounts so you can tilt the seat. if you use the bottom mounts, the seat is just way too "flat" and you can't adjust the angle. you will feel like your butt is sliding forward all the time. also, you will feel like you're slouching all the time because the seat is bolt upright.

GENERAL corbeau bracket top tip:
when bolting it down (after you've widened the hole), if you notice that there is a gap between the bracket and bolt hole, do NOT just crank it down. doing so will bend the bracket, and the slider with it. it will be very difficult to adjust. use a solid spacer of some sort (not a stack of washers).

MR2
03-01-2011, 05:21 PM
bottom mounts? side mounts? picture of what your talking about?

i3igpete
03-01-2011, 05:31 PM
corbeau seat and sparco side mounts:
http://i9.photobucket.com/albums/a65/Faerus2/IMG_2218b.jpg

corbeau side mounts:
http://www.sportseats4u.co.uk/gfx/Corbeau/corbeausidemounts.jpg

for the lowest possible configuration (e.g. helmet space), i recommend ditching the sliders completely. drill and bolt the side mounts directly to the bracket. mount the seat using the lowest holes in the rear, and give yourself a little tilt in the front.

of course, your girlfriend and midgets won't be able to drive your car, but oh well.

MR2
03-01-2011, 09:26 PM
oh wow shit, my seats did not have that option....damn I wish.

i3igpete
03-02-2011, 12:40 AM
which seats did you get? I think the forzas and the fx1's have holes on the side

MR2
03-02-2011, 12:56 AM
skinny CR-1's maybe I should MAKE holes in the side

Goallie11
03-02-2011, 09:34 PM
My FX-1 pro was a bitch to get in, same bracket problem like the rest of you have experienced. Took me a good two hours to grind the holes bigger so it'd fit properly and then I just muscled it into position and cranked it down. It doesn't seem flat to me though, the way I did it.

Head room is definitely lacking, so I would highly recommend those side mounts also.

fullracegt
03-07-2011, 12:25 AM
My FX-1 pro was a bitch to get in, same bracket problem like the rest of you have experienced. Took me a good two hours to grind the holes bigger so it'd fit properly and then I just muscled it into position and cranked it down. It doesn't seem flat to me though, the way I did it.

Head room is definitely lacking, so I would highly recommend those side mounts also.

what did the finished product look like? im goin to be installing the same seats in my car but i havent bought the brackets yet.

Goallie11
03-07-2011, 12:37 AM
what did the finished product look like? im goin to be installing the same seats in my car but i havent bought the brackets yet.

I'll take some pictures for you tomorrow.

i3igpete
03-07-2011, 10:05 AM
headroom with side mounts. rear bolt set to the lowest hole, front bolt set to 2nd from the top. for extra extra headroom, buy a fibgerglass shell type seat, not a tube frame. that way when you take out the seat pads and it will still be comfortable.

http://a4.sphotos.ak.fbcdn.net/hphotos-ak-snc6/198461_10100359885313760_1901292_62813983_5500105_ n.jpg

Goallie11
03-07-2011, 08:14 PM
Heres mine, on the Corbeau sliding bracket.

http://img.photobucket.com/albums/v653/Goallie11/IMAG00122.jpg
http://img.photobucket.com/albums/v653/Goallie11/IMAG00112.jpg

This shows my headroom from the top of the seat, I couldn't get my whole hand in and take a picture at the same time but it's about 3 inches.
http://img.photobucket.com/albums/v653/Goallie11/IMAG00132.jpg

You gain lots of room on either side of the seat, but I did have to flip around the buckle mounting plate to get it to fit.
http://img.photobucket.com/albums/v653/Goallie11/IMAG0014.jpg
http://img.photobucket.com/albums/v653/Goallie11/IMAG0015.jpg

fullracegt
03-15-2011, 10:38 PM
:Dthanks for all the pics they were very helpful. Im pretty sure im gonna go with the sparco side mount brackets,they seem to fit my needs best:mitsu:

dpartinvr4
03-17-2011, 07:38 PM
installed my seats and sliding brackets today, they fit like a glove :).......I love it when it's my turn to have the freak product that actually fits like it's supposed to.

MR2
03-19-2011, 05:01 AM
installed my seats and sliding brackets today, they fit like a glove :).......I love it when it's my turn to have the freak product that actually fits like it's supposed to.

all our whinging was heard then! :p good stuff, they could have done a LOT to improve the brackets.