View Full Version : Checking TPS signal
3000GTCSULB
12-23-2010, 09:41 PM
Here is a noob question, when checking for the voltage on the TPS, does the harness need to be connected to the sensor? TPS = Throttle Position Sensor, for those that did not know.
I suspect one of the following has gone bad:
TPS
ECU
Spark Plugs
Vacuum Leak
The ECU is a year old.
The Plugs are 2 years old.
TPS is original.
I'm getting a jerking acceleration when I'm driving, so I figured I would start here.
mb3000
12-23-2010, 10:04 PM
Here is a noob question, when checking for the voltage on the TPS, does the harness need to be connected to the sensor? TPS = Throttle Position Sensor, for those that did not know.
I suspect one of the following has gone bad:
TPS
ECU
Spark Plugs
Vacuum Leak
The ECU is a year old.
The Plugs are 2 years old.
TPS is original.
I'm getting a jerking acceleration when I'm driving, so I figured I would start here.
Are you getting consistant jerking throughout the rpm range?
3000GTCSULB
12-23-2010, 10:42 PM
Yes, at about 2700-3000. Which makes me shift at 2000 for now. :(
x2percentmilk
12-23-2010, 11:21 PM
Not sure about your problem, but here
http://www.3si.org/wiki/index.php/TPS_Throttle_Position_Sensor_Adjustment
about 1/4 of the way down
mb3000
12-23-2010, 11:31 PM
Yes, at about 2700-3000. Which makes me shift at 2000 for now. :(
If it is only at those rpm's than my guess is that you are getting nasty compressor surge in the colder temps. If this is the case than you probibly have a fmic on your car?
3000GTCSULB
12-23-2010, 11:44 PM
My car has the stock SMIC's. I'm in Southern Cali so the temperature is about 60.
I haven't tried other RPMs because I haven't wanted to accelerate through the jerking.
mb3000
12-24-2010, 12:00 AM
My car has the stock SMIC's. I'm in Southern Cali so the temperature is about 60.
I haven't tried other RPMs because I haven't wanted to accelerate through the jerking.
Well damn, wish it was as simple as a little surging.
You set the tps with the harness disconnected, but it needs voltage to check the output signal. You could probably wedge a wire into the output at the ecu and read the voltage there. I would use a datalogger though- much easier.
stealthee
12-24-2010, 02:49 PM
How old are the plug wires?
3000GTCSULB
12-24-2010, 03:07 PM
Wires are 2-3 years old based on the previous owner.
ver fer
12-24-2010, 03:17 PM
I would start with changing the plugs and wires. What plugs are you using?
3000GTCSULB
12-24-2010, 03:46 PM
Checked all the vacuum lines, no leaks.
Checked the ECU, everything looked brand new in there.
Next, ill change the plugs and wires. NGK Coppers KR7E gapped at 32. MSD Wires.
I'm pretty much BPU
mb3000
12-24-2010, 04:07 PM
Checked all the vacuum lines, no leaks.
Checked the ECU, everything looked brand new in there.
Next, ill change the plugs and wires. NGK Coppers KR7E gapped at 32. MSD Wires.
I'm pretty much BPU
Sounds like a pretty good plan.
3000GTCSULB
12-24-2010, 08:51 PM
I may have found the culprit. I was putting the plenum back together when I noticed this crack. I this the EGR piping?
http://i88.photobucket.com/albums/k193/Rgarcia9/VR4%20Project/IMAG0071.jpg
I don't know whether this would do it or not, since now I have order one.
stealthee
12-24-2010, 08:57 PM
That should not cause bucking. Mine was completely broken in half. All it did was make my car sound like a tractor.
3000GTCSULB
12-25-2010, 12:27 AM
SUCCESS!!! Car is no longer stuttering on acceleration.
TPS checked out okay for voltage.
I also cleaned the Idle Control Sensor since I had the Y-Pipe off. I'm pretty sure it was the spark plug wires that were bad.
On the coil pack, some of them looked white, and others locked yellow on the inside. Does that give some type of indication?
Now the only thing I'm hearing is some type of slight ticking while driving. I'll have to check that out next. The tick only happens when in gear, in neutral I can't hear it.
stealthee
12-25-2010, 09:45 AM
Awesome news.
KeithMac
12-26-2010, 07:02 AM
The coils have two different colour lead sockets, on is silver and the other is brass. If you had corrosion/white powder on the plug lead ends then that would cause a poor connection.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.