PDA

View Full Version : Virtual Dyno Software for AEM & Emanage Ultimate (How To & Charts to check out)



Trevor
10-12-2010, 12:45 AM
I'm kinda bored now so I figured I'd post up a "How to" on the Virtual Dyno software I've been using. I'm damn impressed with it so that's why I'm bothering to post. ;)

You can find the software here:
BradBarnhill.com (http://www.bradbarnhill.com/projects/VirtualDyno/)
Where I found the software:
http://forums.evolutionm.net/ecuflash/500150-virtual-dyno-standalone-software.html

It kicks out charts that look like this. Well maybe not this much torque at 16 psi. :p
http://members.cox.net/angelajames/600lbft.gif

*Dumbed down (but still geek) speak*
It works buy using the mass of the car and wind resistance as the resistive force instead of the dyno rollers. The coefficient of drag and frontal are of the car is already plugged into the software (behind the scenes). The engine rpm rate of change is referenced versus the mass and wind resistance from the pull to come up with wheel power.
*/Geek speak*

As dauting as these instructions look this software is actually pretty easy to use. Just about anyone can get this thing to kick out a graph. My instructions add a few steps because this is everything you can do to get the most accurate results from the software.

Important things to remember to ensure a accurate graph:
- Set your datalogging system to the maximum sample rate (250 samples/sec with the AEM & 20ms (50/sec) with the Emanage Ultimate). When you output the data to a *.txt or *.csv file select the fastest rate also. Slow sample rates will not help your accuracy.
- Weigh your car (and you & your stuff for that matter). The total mass of the moving car must be correct. You even need to account for the fuel that's in it. (Gas is roughly 6.1 lbs/gallon)
- Make sure your tire height is correct. Go to your tire manufacturer's website, narrow down to your tire model/size, and the tire height should be listed in the specs.
- You must do your pulls on a flat road.
- You shouldn't need more than 5 smoothing in the software to get a decently smooth chart. Anything more and you're probably having some issues with smooth power delivery.

A pointer...don't use this to tune the car unless the pulls are on same same stretch of road, going the same direction, & in the (exact) same weather. That pretty much means if you go out to tune you need to finish what you start and you shouldn't make changes to the timing based on a run from yesterday versus a run from today. Things like temperature, uncorrected barometric pressure, wind, and the grade of the road you do the pulls on makes comparisons from different days and locations impossible for the purposes of tuning. Now you can compare them for "gee whiz" fun...but don't tune like that.

__So on to the "How to"__________________________________
AEM:
- Install Virtual Dyno
- Open the software and go to "file", "options" and type "Engine Load" next to Boost (That'll be unnecessary in the next release / 1.0.7)
- Make sure the AEM's internal logger is set to record at 250 samples a second and is recoding (at minimum) Engine Speed, Engine Load, O2 #1 (or 2), & Throttle
- Do a single pull in 3rd and download it out of the computer. 4th is not necessary and is pretty damn dangerous. I usually start my pulls at 1500-2000 to make sure I give the turbo every chance to spool early.
- Open AEMLog and the pull file. Stick with one plot and select the "Overlays" button.
- Plot Engine Speed, Engine Load, O2 #1, & Throttle
- Zoom in on just the single pull (IE 1500 rpm to whatever your redline is). Nothing more.
- Go to file and hit "export as text"
- Select Engine Speed, Engine Load, O2 #1, & Throttle
- Select "current zoom data"
- Make sure the "restrict data rate" is still on "fastest" and the data is "Real"
- Hit export and put the file on your desktop
- Open Virtual Dyno and drag that file into the left pane
- Fix all the info in the box on the left. Ensure it's accurate.
- Boom! There's your graph!

_________________________________________
Emanage Ultimate:
- Install Virtual Dyno
- Open the software and go to "file", "options"
- make sure "Auto Trim TPS" is active/checked
- Type in these "Custom Column Names"
Time - msec
RPM - Engine Speed(rpm)
AFR - A/F Meter(0-5v) 1 (or 2 depending)
TPS - Throttle Position(%)
Boost - GReddy Pressure Sensor PSI 1 (or 2 depending)
- Make sure the Ultimate's internal logger is set to record at 20ms and is recoding (at minimum) Engine Speed, the A/F Meter, the Greddy Pressure Sensor, & Throttle Position
- Do a single pull in 3rd and download it out of the computer. 4th is not necessary and is pretty damn dangerous. I usually start my pulls at 1500-2000 to make sure I give the turbo every chance to spool early. Stop the logger immediately after you lift off the gas.
- Open the Logger and the pull file.
- Hit save (the little floppy disk in the corner).
- Change the "Save as type" to a Text file
- Browse to your desktop, name it, and hit Save
- Open Virtual Dyno and drag that file into the left pane
- Fix all the info in the box on the left. Ensure it's accurate.
- Boom! There's your graph!

As far as the Ultimate goes I sent the designer all of the header names and it should have native Ultimate support in the next release. That and support for S2000's. http://www.clicksmilies.com/s1106/teufel/devil-smiley-059.gif


--------------------------------------
So there ya have it. I want to see some graphs so post em if you got em! And no screwing around! ;) You're on your honor here. No 1st gear pulls in a 5000lb car while going down the side of a mountain!

Trevor
10-12-2010, 01:01 AM
And a quick note...athough it's very accurate and damn close to a real dyno at the end of the day it's not a real Dynojet or Mustang.

Now providing everyone inputs good base info the VD charts posted should be relative & comparative to each other. Apples to Apples most definitely.

Now what would be realy cool is to see VD charts from logs taken on real dynos and what they look like next to each other!

Trevor
10-12-2010, 01:21 AM
Old school. EVO3's pegged out on a Mustang. The real dyno chart is not to trusted though. The dyno operator didn't use an inductive pickup then proceeded to set the RPM vs roller speed reference wrong. When we lifted at 7911 according to the Ultimate the dyno said we were only at 7433. :rolleyes:

http://members.cox.net/angelajames/mustang.jpg

http://members.cox.net/angelajames/mustangvd.jpg

terrets
10-12-2010, 02:18 AM
Very cool. Ill be sure to use this after winter. Haha

B-Man
10-12-2010, 08:15 PM
I'll have to use this on my e-manage when I get a chance. Too bad I don't know the exact weight of my car :(

terrets
10-13-2010, 02:59 AM
I'll have to use this on my e-manage when I get a chance. Too bad I don't know the exact weight of my car :(

Just go to a weigh station or somewhere that sells soil/stones. Offer them a few bucks :D.

B-Man
10-13-2010, 10:12 AM
I need to find one is the problem.

terrets
10-13-2010, 04:49 PM
Do you live in bumfuck Egypt? :D

Trevor
10-13-2010, 11:42 PM
I need to find one is the problem.
http://catscale.findlocation.com/
They'll weigh cars and it's usually around $9.

B-Man
10-14-2010, 09:50 AM
Do you live in bumfuck Egypt? :D

No, I live in the middle of a city. Not much dirt sales go on in the city.

B-Man
10-14-2010, 09:51 AM
http://catscale.findlocation.com/
They'll weigh cars and it's usually around $9.

Thanks, I found one not too far away.

B-Man
10-15-2010, 08:23 AM
For the EMU, do we type in the fields just what you wrote before the '-' or the entire line?

Trevor
10-15-2010, 01:10 PM
For the EMU, do we type in the fields just what you wrote before the '-' or the entire line?
The info after the dash (not the whole line).

Make sure the O2 1 or 2 and the pressure sensor 1 or 2 are referenced to the correct inputs (IE your pressure sensor could be on 1 with your widbeand on 2 or it could be the flip-flopped...just depends on how you hooked em up).

B-Man
10-18-2010, 07:03 PM
So, I'm doing something wrong. It says I have 1163HP lol. AFR and Wideband look right. I'll post the log in a few.

B-Man
10-18-2010, 07:12 PM
Hopefully this works. The first file is the log I took. I cut out any of the file that isn't 100% throttle.

B-Man
10-18-2010, 07:16 PM
Graph:
1287

mh3kgt
10-18-2010, 08:01 PM
How do I get this to work with my MMCd log files? It's a .csv file, but every time I go to load it in VD it has an error saying "wrong input string" or something of the sort.

B-Man
10-18-2010, 08:27 PM
The label row (usually top row of CSV) need to be inputted into the options field (File->options)

Trevor
10-18-2010, 10:44 PM
You sure that wasn't a second gear pull? That's what it looks like.

B-Man
10-18-2010, 10:56 PM
Pretty sure. Does 5.8sec from 2-6k not make sense in 3rd gear?

mh3kgt
10-19-2010, 11:41 AM
The label row (usually top row of CSV) need to be inputted into the options field (File->options)

Yeah I already went through and set VD labels to match exactly my .csv file, and still no luck. Still get an error saying wrong input string :(

B-Man
10-19-2010, 12:05 PM
Post the log.

B-Man
10-19-2010, 12:13 PM
Is the input supposed to be in milliseconds or seconds?

mh3kgt
10-19-2010, 12:22 PM
1289 This should be my most recent 3rd gear pull...see if you can get it to work with VD lol, cuz I'm apparently a retard :p


*edit* hrmm not sure if I attached that right...lemme know if it works or not

B-Man
10-19-2010, 12:26 PM
It's def not gonna work with the time like that. It's gonna see all the times are the same and not know what to do with it. Also, you're missing a label so things won't line up.

mh3kgt
10-19-2010, 12:27 PM
I dunno why excel shows the time like that, if I open it in openoffice the time is just fine grr microsoft :( or are you meaning that all the times are 17:31?

B-Man
10-19-2010, 12:28 PM
All times are at 17:31.

mh3kgt
10-19-2010, 12:40 PM
Hmm wonder how I change the settings in MMCd for it to display the time correctly

Chris@Rvengeperformance
10-19-2010, 12:58 PM
very nice program, "seems" to read a bit high so far, but I have not done a full pull yet. I ran it to 4000 RPM in 3rd and it is showing 435 ft/lbs at 3755 RPM. I would think 375 would be more realistic for the tune and boost I'm running right now.

I'm not sure if my sampling rate is high enough, I'm datalogging through my scanmaster into HHH. I have HHH setup to poll the RPM every 30 ms and I am only logging RPM,TPS,KNOCK, and AFR.

I have exported the file to csv with a line outputted every 10 MS to be sure it has the most granular data possible.

I'm wondering if a direct logging connection to the ECU using the Evoscan OBD1 cable would provide more accurate results.

It does definitely correlate to my butt dyno and I had some knock on that pull that showed up as a big dip in the graph, so it is certainly useful for tuning. I am amazed how much power just a little knock cost. It shows that 5 knock counts caused me to lose 20 ft/lbs of torque.

mh3kgt
10-19-2010, 01:03 PM
What is another good free datalogging program for us 1g guys? Seems like MMCd isn't liking VD so far...

Chris@Rvengeperformance
10-19-2010, 01:41 PM
if you are logging on a notebook pay the small fee and get HHH

mh3kgt
10-19-2010, 02:44 PM
I suppose I could log on my laptop, but the battery life sucks lol I normally just use my Palm and MMCd. Wait, doesn't TunerproRT have a logging feature as well? I could just log straight off my Maftpro I guess

blindmist
10-19-2010, 04:57 PM
if you are logging on a notebook pay the small fee and get HHH

I completely agree. HHH is DAMN WELL worth the money. I still use it over my Emanage Ultimate logger. The cable is easy enough to make if you have a diode and a 10k resistor and some spade connectors to fit on the pin.

SilverJester
10-19-2010, 11:13 PM
TunerPro RT does have a logging feature. I used it instead of HHH for use with Virtual Dyno because I can read both boost and wideband (I have the wideband hooked in through the ecu's egrt so HHH can read it but not the boost). But the maft-pro doesn't log on it's own, in order to log you need a laptop connected to you maft-pro. Also, you need tunerpro rt V5 (which is in beta right now) because V4 doesn't log the time at which each sample is taken.

mh3kgt
10-20-2010, 01:10 AM
thanks for the info I'll have to see what I can do with TunerproRT

Chris@Rvengeperformance
10-25-2010, 07:20 PM
I have done some full pulls and they are now also reading around 1150 HP. Is the sampling rate through my setup just too low? It is half way sane until the RPM data is quite smooth in the upper revs.

FYI it doesn't look worth it trying to log through the e-manage blue, the claimed sample rate I have seen is only 10 per second!

B-Man
11-12-2010, 09:55 PM
So, I happened to be looking through a log and noticed that the sampling changes from 20ms to 200ms. I'd imagine if the program was written incorrectly, it would cause the 1000hp issue. Going to look into why it changes in the log some more.

Boostaddict
11-16-2010, 10:07 PM
BTW for shits and giggles I plotted an aem log that I took on the dyno last week (or was it the week before... time flies). Anyway, they were damn close!

R/T93
11-16-2010, 10:14 PM
I have shown 310-330 whp and 340-360 tq.

Seems a bit high but not unbelievable.

A dyno program I got for my Droid also said 330 whp, at least they are consistent!