View Full Version : automatic vr4?
hyper3000gt
08-04-2013, 05:21 PM
has anyone ever managed to put the awd automatic into a vr4? or are the awd tt conversions I've seen done start out as an already automatic SL just with the vr4s engine swaped in?
donniekak
08-04-2013, 07:02 PM
Several people have done this. I believe there is a semi how to on the other forum.
Nationalmilkman
08-04-2013, 08:57 PM
I know of 2 running/driving Auto VR4 and an Auto TT in the works.
hyper3000gt
08-04-2013, 09:31 PM
Several people have done this. I believe there is a semi how to on the other forum.
do you have a link to it? I'm just really curious how this is done. I understand how to make a turbo SL just by dropping in the engine from the vr4 with all supporting piping and oil lines and what not but installing the auto in a vr4 might be tricky. does anyone know if the whole dash would have to come out to install the necessary wiring? How does the automatic tranny's computer communicate with the vr4's engine ECU?
hyper3000gt
08-05-2013, 01:14 AM
has anyone seen baddvr4 around? I think he knew some stuff about this particular conversion.
Blue91SL
08-05-2013, 01:24 AM
All GTOs were AWD, even the N/A cars. N/A came with automatic, but still AWD. You can find one of those transmissions on ebay, and swap it in. Pretty straight forward. Don't know Alison's name on the forums, but she's got an AWD ATX VR4 running on the strip.
hyper3000gt
08-05-2013, 01:42 AM
yea I would like to speak with someone that's done it, so I know what all is involved I might be doing this conversion my self sometime soon, but I don't want to get in over my head. the main things I need to know is how difficult it is to put in all the wiring that's required for the awd tranny. obviously in a manual there is no wiring so I would have to put all that in my self and also get the proper ecu for it as well.
does anyone know if this can be done only by working under the hood and just removing the center counsel or would the whole front dash from the inside of the car need to be removed to place the wires correctly?
ICPREY
08-05-2013, 01:42 AM
has anyone seen baddvr4 around? I think he knew some stuff about this particular conversion.
Thad or IPD has a conversion built car, but I think it's a SL body or Stealth with VR4 parts and automatic transmission. I may be wrong, but I'm sure he'll chime in...
TurboSinceBirth
08-05-2013, 02:19 AM
PM 11SecondFWD. He put a GTO AWD ATX transmission in a VR-4 and ran some high 10s at the track on DR-650s.
hyper3000gt
08-05-2013, 02:48 AM
sounds good thanks turbosincebirth!
my car started as a 95 base 3kgt n/a atx & is now tt awd atx. the "hard part" of the conversion is really just making the TCU talk to the ECU. the thing is...now that we have flashable ECU's...the difficulty therein might be moot anymore.
of course, if you just want "stock atx vr4", then you don't really even need that. you can just piggyback the stock N/A ecu on an ATX and not worry about it--but you'll be limited on how much fuel you can run.
having been down this route--and given the new options available--i'd say the ideal starting point is a tt/vr4 that you ATX convert. this eliminates the need for injector resistors, and also eliminates the mount-angle on the rear suspension. the latter is what makes using coilovers dicey, due to the rear axle flanges.
p.s.
it's had a 2g r/t rear bumper conversion & a 97 front bumper & 99 headlights added. hence the confusion over what exactly it "is".
hyper3000gt
08-05-2013, 04:38 PM
So from what your telling me once I get a flashable ecu it's easy to make it talk to the tcu, you can pretty much program it to do anything want not just things related to fuel?
but if I wanted to remain stock how can I piggyback the stock ecu to the auto TCU?
What kind of wiring is involved with this?
and what do you mean by the mount angle on the rear suspension is this different between the vr4 and the bases/ sls?
sergechronos
08-05-2013, 06:07 PM
my car started as a 95 base 3kgt n/a atx & is now tt awd atx. the "hard part" of the conversion is really just making the TCU talk to the ECU. the thing is...now that we have flashable ECU's...the difficulty therein might be moot anymore.
hence the confusion over what exactly it "is".
Believe you have said before specifically that it is: A pain in your ass.
So from what your telling me once I get a flashable ecu it's easy to make it talk to the tcu, you can pretty much program it to do anything want not just things related to fuel?
but if I wanted to remain stock how can I piggyback the stock ecu to the auto TCU?
What kind of wiring is involved with this?
and what do you mean by the mount angle on the rear suspension is this different between the vr4 and the bases/ sls?
He's saying it's POSSIBLE with a Flashable ECU that it may not be hard to get the ECU and TCU to talk anymore, but that's an unknown. Don't know anyone doing it. The Flashable ECU lets you adjust just about everything related to the car, but you will still have to get the TCU to play nice with it. Theoretically you could get one of the AWD NA auto trans from a GTO with all the wiring and such, but using it with the Chromed ECU is an unknown.
And I believe what he's referring to with the rear suspension is the work that is involved in turning a base/SL into an AWD car with the subframe. Several people have done it, more than a few will tell you that they wish they had just bought a VR4 instead.
If you really want to go through with this, Hans @GZP may be able to answer a few of the questions with an auto AWD TT as I think that they did this before. You may be in over your head though trying to do a swap of this size.
my photo album has a pic or two of the rear axle flange. z11's converted to z15/16's will have a more slack angle on the suspension. this means that there is less clearance between the shock & the axle flange. my coilovers literally touch the axle flange when my car is in the air. this is a known factor for fwd > awd conversions. the stock awd shocks won't have this problem...but the rear end will sit very low. that's not necessarily a bad thing, but with 285 tires, i was scoring the rubber on the fenders each time i'd hit a sizable bump.
TurboSinceBirth
08-05-2013, 09:43 PM
Right now there isn't anything that can be done to use the flashed ecu to control the atx. We don't even know if the TCU's are flashable or editable in any way. I don't think Greg is going to mess with it or even see if he can decipher the code even if we were able to read and write to it. Even with a shift kit using the TCU you're still extremely limited on how much power it will handle. Eliminating the TCU and running the two solenoids off a toggle switch is better but I'm sure past TD04 turbo you will see the weakness of the end clutches, etc. 11SecondFWD ran his ATX off of toggle switches to shift which gives 100% fully engaged shifts no slipping that the TCU will use for comfortable OEM driving.
It would be nice to only mess with the switches part of the time when you drag race and I'm sure the DSMers have figured out a way to use both the TCU and direct connection to the solenoids, but at the very least you could wire up your shift toggles to paddles or buttons on the steering wheel. I saw one person with an aftermarket steering wheel that had two NOS buttons. He used those to up/down shift. The paddle shifters would have to be custom made or custom retrofitted off a different car.
I can't quite give up rowing gears since I only have one performance vehicle which will remain manual until I get too old to operate the clutch but if I were to get another 3S I would definitely swap an ATX in to make a quick straight line car. You don't have to spend $2-3k upgrading the drivetrain on an ATX to run 10s whereas you have to do that on either 5 or 6 speed.
hyper3000gt
08-05-2013, 11:25 PM
who are the DSMers? and even if I have to go paddle shifter this doesn't bother me at all, I have no problem going that rout if that's what it takes.
sergechronos
08-05-2013, 11:29 PM
DSMers = people who own 91-99 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser. Pretty sure that the AWD turbo versions of those used the same transmission as the GTO AWD tranny.
same internals--different bell housing. 46g3 doesn't bolt up like a 6g72. my w4a33 came from a 92 diamante, iirc.
i don't think a flashable TCU is the way to go. i think that's superfluous. it has to do with the ECU reading the inputs from the TCU--that's it. the ATX doesn't need to be controlled by the ECU, just let the TCU do it's job. this is what i'm unsure of--because to my knowledge, no one has posted up on how to make a flashable ECU read those signals that would normally have to be hard-wired from the TCU.
and yes, the w4a33 is significantly cheaper to "beef up". if you do the labor yourself, it's less than a grand in parts--and that's including a HSTC.
hyper3000gt
08-06-2013, 11:50 AM
what about the ecu out of 98/99 automatic sl? wouldn't this already be set up for reading the inputs from the tcu IPD? and then it can just be flashed if I need to adjust the fuel to air ratio for further upgrades/ boosting?
donniekak
08-06-2013, 01:04 PM
I don't know what everyone's issues with the wiring, it's simple. The ecu, and tcu are separate. The only communication needed is some sensor input into the tcu to have the right shift points. If you run a shift box, you don't even need a tcu. Dsm's use the same automatic trans, and it's very simple to do a manual auto swap on them. Lots of the mitsu tcu's are also EPROM, and can be programmed for different shift points.
As far as the ecu is doesn't care if the car is running an auto, or manual trans. The non turbo cars have the same ecu, manual, and auto for each year.
hyper3000gt
08-07-2013, 03:54 AM
ok thanks donniekak that helps a lot. I think me and others included thought the ecu from the vr4 might not communicate with the tcu for the shift points your referring to. I do know at the very least the ecu in the vr4 is different then the manual non turbo cars because the air to fuel ratios are set up differently for turbos and for the lower compression of the engine compared to the stock.
but if the tcu can still get what needs from the vr4s ecu then I think we're in business.
i never said the wiring is difficult--it's just a pain. that's why most people who have chosen to run ATX's ditched the tcu entirely and ran it manually. i wanted a stock-feel to it, so i chose to keep the computer in the loop. personally, i find that the tcu (on pwr mode) is quite capable to the task at hand; upshifts shifts at redline & downshifts in the blink of an eye.
another issue i have with my car is having to hard-wire the fans ON. one more issue that could probably be fixed--had i been able to run a flashable ecu.
ilian51378
09-22-2013, 12:18 AM
I have exactly what you want! I bought a '95 N/A ATX GTO (all GTOs came AWD) and did a TT conversion on it. Then, I bought a shift box and a pair of paddle shifters and wired them in. For now, I have the paddles wired on the trim that covers the steering wheel column so they don't spin with the steering wheel, but I got a great idea on how to make a paddle shifter hub adaptor and install the paddles on the steering wheel. In order to do that, I will have to use the horn wires for the paddles and wire the horn on a separate button, somewhere on the dash.
ilian51378
09-22-2013, 12:21 AM
ok thanks donniekak that helps a lot. I think me and others included thought the ecu from the vr4 might not communicate with the tcu for the shift points your referring to. I do know at the very least the ecu in the vr4 is different then the manual non turbo cars because the air to fuel ratios are set up differently for turbos and for the lower compression of the engine compared to the stock.
but if the tcu can still get what needs from the vr4s ecu then I think we're in business.
It gets everything it needs. I am running a TT ECU in my TT converted N/A ATX GTO with shift box and paddles installed in it.
RealMcCoy
09-22-2013, 04:11 PM
It would be awesome to see the flashable ECU incorporate the torque reduction strategy of the stock system... You could make the trans take much more power if it was shifting in a reduced torque mode,(think NLS for a manual) and recovered power when the shift is completed. The slipping and shift shock under full power is what burns up/breaks parts. Maxing out the pressure will increase clutch holding capacity, but increases shock loads tremendously, and puts hard parts at greater risk.
As far as hardware, I know Brett's new ECU has all the components of both the SL and VR4 ECU, so obviously that can be done. I just have no idea where the software stands in the equation.
Just another project for the programmers... :D
that's pretty much what the TL shift kit is for. also, shifting in PWR mode means it will shift at redline...on the backside of the torque curve.
RealMcCoy
09-22-2013, 05:07 PM
that's pretty much what the TL shift kit is for. also, shifting in PWR mode means it will shift at redline...on the backside of the torque curve.
I won't disagree with you, but I think we're talking about very different levels... I personally prefer the TransGo kits, but the kit modifies the shift timing to reduce slippage and bindup, and increases clutch pressure and volume to minimize slippage. Running it up to redline drops it right into the torque curve after the shift. The entire idea of properly timed shifts is to keep the engine in the torque curve as long as possible. All that is great for car that is below huge power levels.
None of that will save a trans from being broken by big power.... The primary solution to most failures has been higher pressures, and stronger parts. But due to the physical size of the trans, there are limits to it's torque capacity. I was just pointing out that the trans could be made to take some very big power with some creative software.
i guess. i just know that DSM's are running them virtually stock (apart from a shift kit & welded spider), and they're taking 500-600whp regularly without issues.
TurboSinceBirth
09-22-2013, 07:21 PM
11SecondFWD ran DR-750s to high tens at the track with a stock ATX no shift kit, upgraded converter, or any internal modifications. He was making well over 550AWHP also and came within a few tenths of Ray's track numbers so I don't think anyone will discredit it holding the power of bolt-on TD04s sans a stock 4th gear WOT for an duration. If I had the space, time, and money for another 3S build I'd give the ATX a shot since it makes it so simple to run a faster time. Why do you think the GTRs do so well with no driver mod and anyone behind the seat? You can practically sleep behind the wheel because of the relative lack of driver involvementk and ease of use. 7-9k+ powerband you're in all the time plus lightning quick shifts makes it's great for drag racing if you can afford the entry price.
that, and 4a33's are cheap. well, at least the w's are when you import them. the f's can be pricey when used....dunno why.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.