PDA

View Full Version : Corbeau Seat Install



Maximal
07-29-2013, 01:54 PM
Been selling these for a couple years now and finally pulled the trigger on a set for my car. Went with A4's in black and a set of 5 point harnesses.

The two biggest complaints on the Corbeaus over the years have been that their brackets don't fit for shit and their seats sit too high.

We've been working with them on the brackets and they have finally got them that fit. I have had a problem with them sending out the old style brackets but they have ensured me that isn't the case anymore and they should fit fine. That "should" is there because every car can be a bit different so don't be surprised if you have to enlarge the mounting holes a bit. Mine were an old set that I modified to help them figure out how to modify them. Even for them the modification wasn't that drastic. If you have an old set still sitting around let me know and I can give you some measurements to modify.

As for the height issue. Pay the extra for a "shaved base" and you'll end up with an extra inch or so of headroom. Without the shaved based you're at about the same as stock, maybe a little less. I think the problem before was the way people were modifying the old brackets to fit with washers all over that spaced it up a bit. With that said I can really only comment on the A4 but I imagine most other lines are close to the same height.

Other than that install was pretty straight forward. Old seats out. Belt buckles off the old seats and onto the new ones (wanted to keep the standard belts with the harnesses). Then just bolt everything in. They slide clean (I just have the single locker) and look good.

Harnesses were a straight forward install for the most part. I have a roll bar (which you should have too if you're putting in any harnesses) so the shoulder belts wrapped around that. The outside lap belt connected to where the stock belt connects, I just removed a spacer and bolted the harness there. I did have to drill holes for the submarine belt (in line with the rear mounting points of the seat, centered, be careful with the fuel lines on the passenger side) and on the drive shaft tunnel for the other lap belt. They assumed you were using stock mounting locations so didn't include nuts with the harness hardware. I'll let you know what size to get once I pick some up.

Overall I'm really happy. They're nice quality seats, especially for the price. I see them lasting a long time. They're also super comfortable and the bolsters will hold you in on the track/auto-x/curvy road..I might not even need the harnesses.

If you guys are interested in a set shoot me a PM and I'll get you pricing. They have a decent selection of seats and harnesses. Any questions on the install or anything else about them let me know also. Onto the pics...

https://lh6.googleusercontent.com/-k36oiA8CkUw/UfaCgI16cjI/AAAAAAAAA2o/nVEvV5jGCPo/w949-h712-no/IMG_20130728_173723.jpg

https://lh3.googleusercontent.com/-5e1Oju5xx80/UfaDTXDYZxI/AAAAAAAAA3Y/2F63cqaqVm4/w949-h712-no/IMG_20130728_173556.jpg

https://lh3.googleusercontent.com/-h3Ynbb2cxas/UfaE4w9K-OI/AAAAAAAAA4o/h5YdY5hsKeU/w949-h712-no/IMG_20130728_173623.jpg

Ange
07-29-2013, 04:01 PM
why keep the rear seat if you installed a rollbar? May aswell delete them. Not that they weigh much.

Maximal
07-29-2013, 05:02 PM
Looks mainly. I'll probably get rid of them once I have time to fab something up that can replace them without just seeing floor there.

FeaRpb
07-29-2013, 06:09 PM
Can't wait to get the ones I bought from you installed. They look great.

green-lantern
07-29-2013, 07:46 PM
Looks great Terry, do want......someday


Next time get your finger out the pic though :p

EvanH
07-29-2013, 08:04 PM
If you don't mind me asking, how tall are you, how tall do the seats sit compared to stock, and what is your waist? I have been curious about these for a very long time, just haven't made my mind up if I want new seats or replace old red leather with new.

AdamVR4
07-29-2013, 10:33 PM
Modifications weren't drastic? The modifications necessary to make the brackets fit the car better weren't drastic. The modifications necessary to get the drivers seat down far enough so that I had any space between my helmet and the head liner was drastic... 5'11".

Shaved base? Is this referring to the fiberglass shell on the seat that I had to shave? This was critical and provided a shocking amount of height, but I'm not sure I'd want it done at the factory. This was how I set the lean of the fixed-back seats.

Greg E
07-30-2013, 07:30 AM
I haven't installed mine yet but honestly there is nothing holding me back from doing so. Maybe ill tackle this during the week and post back.

Maximal
07-30-2013, 09:45 AM
If you don't mind me asking, how tall are you, how tall do the seats sit compared to stock, and what is your waist? I have been curious about these for a very long time, just haven't made my mind up if I want new seats or replace old red leather with new.

5'8", 32" waist. I'd say about an extra inch of headroom over stock. I can fit my fist between the top of my head and the headliner with a bit of extra space so probably 5" or so of room.


Modifications weren't drastic? The modifications necessary to make the brackets fit the car better weren't drastic. The modifications necessary to get the drivers seat down far enough so that I had any space between my helmet and the head liner was drastic... 5'11".

Shaved base? Is this referring to the fiberglass shell on the seat that I had to shave? This was critical and provided a shocking amount of height, but I'm not sure I'd want it done at the factory. This was how I set the lean of the fixed-back seats.

Maybe the fixed seats are different. To get the brackets to fit I just had to modify the rear inside mounting point by welding a tab to make it sit higher.

The shaved base seats are exactly that. I went with reclining seats so the lean wasn't an issue. I sit way up on the steering wheel with a straightish back so I imagine most other people would get even more room if they recline and slide back a bit.


I haven't installed mine yet but honestly there is nothing holding me back from doing so. Maybe ill tackle this during the week and post back.

Hopefully you didn't get one of the old sets of brackets with the fitment issues. If so we can exchange them or if you have access to a welder I can show you how to modify them.

Toni
07-30-2013, 01:58 PM
Nice work Terry! This might be a future upgrade of mine if I start doing more road courses.

Maximal
07-31-2013, 09:34 AM
Yeah, I would suggest at least the seats for any type of racing. The harnesses obviously will hold you in for sure but the bolsters on the seats are pretty awesome for keeping you in place side to side at least.

Jeff V.
07-31-2013, 05:45 PM
I've got an older set of Corbeau brackets that I bought from somebody a year or two ago. Would you be willing to do the mods on them and send them back for a fee?

green-lantern
07-31-2013, 10:23 PM
I've got an older set of Corbeau brackets that I bought from somebody a year or two ago. Would you be willing to do the mods on them and send them back for a fee?

We both need a welder.

Maximal
08-01-2013, 09:26 AM
I've got an older set of Corbeau brackets that I bought from somebody a year or two ago. Would you be willing to do the mods on them and send them back for a fee?

Yeah, I probably could. I'm not liking the idea of having to pull my seats again but as long as you're not in a hurry shoot me a PM and we'll work something out.

Maximal
08-05-2013, 03:11 PM
Finished mounting the harnesses this weekend and I love this setup. Huge difference in keeping you in the seat which should help me focus on driving compared to not flying out of the seat.

Greg E
04-07-2014, 08:44 AM
Bought these from Terry some time ago and finally got the chance to install them. The new seat brackets make the install a piece of cake.

http://i.imgur.com/K1QDsT3.jpg
http://i.imgur.com/Ai7kzxQ.jpg

They're pretty idiot proof to install. I had to enlarge one of the mounting holes because it didn't quite line up right but that was an easy fix.

http://i.imgur.com/M6MAXwH.jpg
http://i.imgur.com/3bOr3Ud.jpg
http://i.imgur.com/xNQfJKV.jpg
http://i.imgur.com/7bQO7Iy.jpg

Transferring the seat belt receiver over I found a surprise. Looks like the wire got caught in the seat track and was cut. Also found the SRS light bulb pulled from the dash. Betcha a Taco this is why.

http://i.imgur.com/HwFc4Pu.jpg

The stock bolt is a bit too long. Some washers fixed that.

http://i.imgur.com/S0aJGTD.jpg?1

Seat brackets were an easy install.

http://i.imgur.com/hs4tNK6.jpg

Being a skinner guy, I fit into these comfortably. I would imagine a larger than typical American would have a difficult time with them. Just a heads up.

Thank you terry for the great customer service and quality product!

Disrupter
04-07-2014, 09:32 AM
Looks very nice Greg! My next mod I think.

Maximal
04-07-2014, 10:39 AM
Nice write-up Greg!

Ange
04-07-2014, 11:49 AM
corbeau brackets do they fit for other seats like sparco and bride? or is it different pattern on all those?

Greg E
04-07-2014, 12:36 PM
Someone on another forum was asking me about the height of these. It's a lot like stock to be honest.

Keep in mind though that the seat back itself is taller than a stock seat so if you're like me and sit close to the wheel, you'll need to recline it a bit. Also it seems I have to move the seat back in order to get in/out of the car too.

green-lantern
04-07-2014, 12:53 PM
Looks great, I want to do this if I ever get the spare cash.

FeaRpb
04-07-2014, 02:17 PM
This is nice to see. I still haven't installed mine yet lol. Waiting for the cage to go in first along with the dash.

Maximal
04-07-2014, 02:29 PM
corbeau brackets do they fit for other seats like sparco and bride? or is it different pattern on all those?

Chances are the mounting points are different but it's probably not a ton of work to get them to worth together. Even still it's probably best to buy the actual brackets for the seat though.

Greg E
04-08-2014, 08:17 PM
Passenger side installed today. One of the holes was pretty far off (about 1/4" to 3/8") but that was an easy fix with the 10,000lb punch press at work. :)

If anyone was wondering, yes the seat brackets allow you to keep the stock amp. It even just clears the Montero 315watt amp.

http://i.imgur.com/Y2O1yPy.jpg

My apologies for the crappy cell phone pics but the car is still a work in progress. Ill take better pics when its finished.

http://i.imgur.com/JJn4QpR.jpg
http://i.imgur.com/cY3j4cW.jpg
http://i.imgur.com/uyHnC2i.jpg
http://i.imgur.com/xZ7NSEI.jpg

Maximal
05-20-2014, 10:40 AM
With the new site we've got even more Corbeau options... Corbeau - Maximal Performance - Street - Strip - Track (http://store.maximalperformance.com/corbeau/b-10165.aspx)