PDA

View Full Version : Not Running Right After Evo Injector Install



HLxDrummer
05-05-2013, 09:11 PM
Well I finally got around to installing my Evo 560s today. Everything was going smoothly for once until I fired it up after the install.

Sounded like a truck at first with 600CC (what the injectors actually flowed) and latencies off the EvoM board. Then tried the latencies from this board and it got a little better. Then put 560CC and got a little better but still doesn't sound right. Wideband says it is running ~16:1 at idle. If I rev it it sputters as the revs rise but if I hold the RPMs steady is sounds about the same as idle. When I let off it will read 12:1 for a second.

Trims are ~120 low and mid (can't remember exactly) and 100 high. They were about 120/110/100 before the install (didn't reset the computer). The O2 trim fluctuates from 100 to 120.

CEL came on after a while but when I tried to read it is says speed sensor.. I am not real familiar with Evoscan though so maybe I picked the wrong setting? Evoscan 2.9 and Chrome V2.

When I disabled injectors they all made an impact (which varied from injector to injector) except #4. Please tell me this is the middle one on the rear bank lol

I don't see any leaks on the front bank and don't smell any fuel. New O-rings and insulators. Put the retaining clips back in the plugs as well as the metal thing that holds them on the rail.

Fuel pressure is good.

Only things I can think of are:
1. Messed up flash ECU settings (all I changed was injector size and latencies).
2. Messed up wiring - the wires sound pretty crispy when I was doing the install. I tried wiggling what I could reach and it didn't change anything though.
3. Forgot to plug something back in/put something back on - I followed the stealth316 tutorial if you are wondering what I removed.
4. Vacuum leak - I did use a new plenum gasket though.

What should I do? Any ideas?

Should I put the stock ones back in (rule out electrical), rearrange the Evo injectors (isolate the problem to one injector), remove plenum and cut back the sheath on the wiring to inspect it/run continuity test, something else? I don't have a compressor here or I would pressure test. Any other ideas? I am busy with school (this past weekend I had some time off) so whatever is the most time efficient is the ticket for me.

Thank you!

ChargerX3
05-06-2013, 03:10 AM
What numbers did you use for your injectors?

GTO-SIMON
05-06-2013, 06:07 AM
hi ,mate ,not alot of poeople use the 560 evo injectors over here in uk on gto,s they always seem to have issues < almost imposible to set up on our cars> if you contact rob at evil empire uk he maybe able to tell you more.there is not nothing he dont know about these cars simon

HLxDrummer
05-06-2013, 09:02 AM
I tried these values:

4.7V/3.312mSec 7.0V/1.680mSec 9.4V/1.032mSec 11.7V/0.672mSec 14.0V/0.432mSec 16.4V/0.264mSec 18.6V/0.144mSec

and these:

16V - 0.628
14V - 0.748
12V - 0.928
10V - 1.208
8V - 1.688
6V - 1.900

Greg E
05-06-2013, 10:13 AM
Evoscan 2.9 can't read/clear CELs. It is broken.

Greg E
05-06-2013, 10:15 AM
hi ,mate ,not alot of poeople use the 560 evo injectors over here in uk on gto,s they always seem to have issues < almost imposible to set up on our cars> if you contact rob at evil empire uk he maybe able to tell you more.there is not nothing he dont know about these cars simon

Huh???

HLxDrummer
05-06-2013, 10:45 AM
Hm.. any other way I can read them? I don't remember if I can with my LCDBC or not.

Chris@Rvengeperformance
05-06-2013, 11:41 AM
I tried these values:

4.7V/3.312mSec 7.0V/1.680mSec 9.4V/1.032mSec 11.7V/0.672mSec 14.0V/0.432mSec 16.4V/0.264mSec 18.6V/0.144mSec

and these:

16V - 0.628
14V - 0.748
12V - 0.928
10V - 1.208
8V - 1.688
6V - 1.900

The first string of numbers is what I always used with the 560s. I did use 535 for the scaling, but every car is different.

read the cel with evoscan 2.6, if you email hamish he will get you a license for the older version. See my thread about deleting the ftdxxxx dll in the evoscan 2.6 folder.

Chris@Rvengeperformance
05-06-2013, 11:42 AM
Huh???

I believe what Simon is referring to is the problems people run into using the 560s with the stock ecu. It is extremely difficult to get the car to idle stoic.

They work perfect when setup on the flash ecu.

HLxDrummer
05-06-2013, 01:02 PM
The first string of numbers is what I always used with the 560s. I did use 535 for the scaling, but every car is different.

read the cel with evoscan 2.6, if you email hamish he will get you a license for the older version. See my thread about deleting the ftdxxxx dll in the evoscan 2.6 folder.


Ya the first set is what I am using now and which made it run better than the second set.

I will try to get 2.6 installed again (that is what I was running with V1) and see what that says. I tried pulling the code with my LCDBC but it isn't working right..

HLxDrummer
05-06-2013, 05:01 PM
Alright I pulled the code - just a random misfire. I was hoping it would say injector 4 was out and cross my fingers that it somehow got unplugged.

Any ideas other than pulling it apart and checking everything? I wish I could run the car with the plenum off lol

Chris@Rvengeperformance
05-06-2013, 06:06 PM
What is the history of the injectors?

HLxDrummer
05-06-2013, 09:10 PM
I bought them off Evotuner on 3Si. Said he cleaned and flow tested them. According to the sheet he gave me all the resistances are +/- 0.1 and they all flow 600CC +/- 1CC. I was going to double check the resistances myself but got lazy and didn't.

Greg E
05-06-2013, 09:32 PM
I doubt your injectors are the problem.

HLxDrummer
05-07-2013, 01:15 PM
Why do you say that? I doubt they are as well, just wanted to see your reasoning.

Do you know which injector number 4 is?

If I can take some time off this weekend I'll probably check the continuity of the rear bank wires (if that includes #4) from the plug to the bigger plug that bolts to the plenum as well as ensuring that they are actually plugged into the injectors correctly. If that stuff is all good then I'll probably switch a few injectors around and go from there.

I'm guessing I can't apply 12V to the injector as a crude way of testing them, right? Would be cool if I could leave them on the rail and jump the fuel pump to make sure they are spraying.

Chris@Rvengeperformance
05-07-2013, 01:17 PM
yes you can, but most places recommend using a 9volt battery for safety. It is unlikely evotuner sent bad injectors, those were the same ones I was running.

It is some work, but if it were me I'd put the stock injectors back in with the stock settings and see if the problem goes away. That should eliminate wiring or some other issue as a problem.

Greg E
05-07-2013, 02:20 PM
Why do you say that? I doubt they are as well, just wanted to see your reasoning.

Do you know which injector number 4 is?

Experience. :p

See it all the time. Guys replace their injectors but not the rubber insulators which seal the injector to the lower intake plenum. I bet if you did a pressure test, you'll find the seal for injector #4 (center rear cylinder) is leaking.

Guys running piggy back can get away with this intake leak because they just adjust the airflow signal for it. Flash ECU is a bit more precise than that.

Greg E
05-07-2013, 02:26 PM
EVO injectors are denso injectors like ours but the sealing surface of the injector heads are slightly different size than ours. I bet you every single car out there with "bad EVO injectors" are the result of this seal leaking.

HLxDrummer
05-07-2013, 02:31 PM
Dude! I test fitted the insulator on the evo injector and I thought it fit looser than on the stock ones! I thought it was my imagination/it would go away when they were torqued down. Is there a solution if that is the problem? All the insulators fit the same so its not like there was a bad seal.

Greg E
05-07-2013, 02:58 PM
If you buy NEW OEM ones, they will seal perfectly again. :)

J-Groove
05-07-2013, 03:03 PM
If you buy NEW OEM ones, they will seal perfectly again. :)

:stupid:

I had to do that as well.

-John

Jimvr4
05-07-2013, 03:38 PM
Adds this to the list of things to check on my build, thanks!

HLxDrummer
05-07-2013, 03:41 PM
I bought new oem everything. The injectors also came with new seals/insulators/etc (forgot that when I ordered OEM). The OEM and the ones on the injectors both fit the same (felt a little loose).. should I try again with the new OEM ones?

Also, if the problem is just a boost leak why would killing injector 4 not affect the engine?

Greg E
05-07-2013, 03:44 PM
I bought new oem everything. The injectors also came with new seals/insulators/etc (forgot that when I ordered OEM). The OEM and the ones on the injectors both fit the same (felt a little loose).. should I try again with the new OEM ones?

Also, if the problem is just a boost leak why would killing injector 4 not affect the engine?

Probably because that injector seal is leaking worse than the others.

Pressure test and find out.

HLxDrummer
05-07-2013, 08:41 PM
It is going to be hard for me to pressure test unless I go out and buy a compressor or put in the stock injector and wait until summer, swap them again, then pressure test at my Dad's (which would take the place of some other things I need to do to my car there).

Would it be a dumb idea to spray starter fluid around the lower seals to detect a leak?

What would I do to fix it if there was a leak?

Also I should mention the new plenum gasket I installed was slightly bent from shipping. I figured once I set the plenum on it that it would flatten out, however. It wasn't kinked or folded or anything.

Thank you for all the help guys, I really do appreciate it!

Greg E
05-07-2013, 11:26 PM
I'm sorry, but you were presented with not only a problem, but a test for that issue to verify and a solution if the verification checks out... Can't help you beyond that.

ChargerX3
05-08-2013, 04:46 AM
You can lead a horse to water...

HLxDrummer
05-08-2013, 09:40 AM
Well what is the solution? That is what I want to know lol Trying to throw parts at it in an effort to save time over testing things and still probably having to throw parts at it.

I mentioned in the original post that I can't pressure test so I was kind of asking for things I could actually do..

DocWalt
05-08-2013, 09:48 AM
Without pressure testing it you're just throwing parts at it ;)

HLxDrummer
05-08-2013, 09:52 AM
Without pressure testing it you're just throwing parts at it ;)

My goal IS to throw parts at it lol I don't have the time right now to be economical in my diagnosis. School is more important right now. I just had a few specific questions (what to do to fix seals, will starting fluid damage the seals, etc)

The part number for the Evo seals and our seals are the same so I guess the seals I got should work even though they didn't fit the same as stock. This weekend I'm gunna tear it apart, check the injectors (resistance and spray), check the wiring, replace the lower seals, and check out the plenum gasket. If that doesn't fix it then it can sit lol

DocWalt
05-08-2013, 09:57 AM
They didn't fit the same because the seals crushed to fit the stock injectors. Starting fluid shouldn't damage them, and they probably leak anyway so does it matter? :p Good luck :)

HLxDrummer
05-10-2013, 08:57 PM
Alright I took it apart again and put the injector from cylinder 4 to the front. I also smeared some petroleum jelly around the seals. Went to kill the injectors and Evoscan isn't working right. OBDII won't bring up the actuatutor buttons, MUTIII says connection successful but that the was an error and the 3000GT setting freezes. I'm not sure which I used last time or what the problem is. Only change I made was uninstalling 2.9, installing 2.6 and deleting the file Forest said to get rid of. I tried reinstalling 2.9, same issue.

It is idling much better now. AFR is right, trims are around 100, etc. Except once in a while the RPMs will drop real low and it will stall/almost stall. Not sure what the issue is there... Wish I could pressure test!

Do the seals use the top/bottom of the seal to actually seal or is the center used? I can't imagine how they would ever work if they use the center..

Any tips? Thanks!

Greg E
05-10-2013, 10:00 PM
I gotta do a step by step thread on setting idle via SAS mode...

HLxDrummer
05-10-2013, 10:27 PM
That would be helpful with all the flash ECU settings. I have played with the basic idle stuff a little but didn't see much need for it (at least before the injector install). You think those settings need tweaked in my case?

Seems weird it is intermittent.. Going to try to take it for a spin tomorrow and see how it fares.

Do you happen to know anything about why Evoscan isn't disabling the injectors suddenly? I hate to bother you with that but you know so much about Evoscan/ECU flash..

Greg E
05-10-2013, 11:25 PM
Evoscan 2.9 sucks... Definitely gojbg to be stepping back for the next version of chrome b

HLxDrummer
05-12-2013, 05:12 PM
Alright I have a little update. After I took it apart again and put petreoleum jelly/etc. it seemed to be smoother but once in a while would sound like it was going to install. Never took it out of the garage though (didn't have a ton of time and a friend's motorcycle was blocking me in).

Today I decided to move the bike and go for a spin. Seemed to run just fine. Every once in a while it seemed like there was a little hiccup but that is probably attributable to me being paranoid and my coilovers. Fuel trims are around 85/115/100 but I only drove it for like half an hour. This is also after I flashed the injector size as 600 (got ECUflash to work but not Evoscan). Not sure why the trims are under 100 when I probably have boost leaks and I put the injector size as what they actually flowed.. oh well.

Not sure what fixed the issue.. probably either the jelly sealing the little gaps or me cleaning the holes in the manifold really well. I also did a little torque pattern on the rails so maybe that helped? Hopefully it stays this way for a while or at least until I can get my hands on a compressor.

Thanks for all the help everyone.

Greg E
05-12-2013, 07:30 PM
Read my new thread on tuning fuel trims. ;)

HLxDrummer
05-28-2013, 09:05 PM
Alright this is getting real old..

Trims have been real low (low ~ 80, mid somewhere around 80, high 100). The O2 trim or whatever you wanna call it went anywhere from 42 to 130 (with a very slight delay between these two extremes). This is with 600CC scaling. I could drive it but it wasn't as smooth as it should be.

Changed the scaling to 535 (without resetting the trims) and it drove decent but the trims didn't really change. Changed the scaling to 510 and reset the trims. Ran like shit and the O2 trim is still really low so I just parked it.

I'm about to just put the stock injectors in and buy a 550 set that fits right later in life and change my NBO2s. Any other ideas? I'm just frustrated because I literally have 8 weekends off total this summer for me to have fun/get stuff done on the car/do stuff around the house and then I will basically have 0 time for anything remotely fun for the next six years. I don't want to be messing around with this POS the entire time and not even get to autocross it. This is on top of needing to replace my oil cooler lines, AC compressor bearing, etc. And I can't do those things or pressure test unless I go 1.5 hours to my Dad's house (which is one weekend at least gone if I do all that and try to fix my injector issue).

Should I just put stock in and say screw it?

The stock O2s cycle but not real evenly. They like to stick near 0V for a little bit. I am pretty sure they are original. And I briefly drove with them unplugged in the past trying to disable closed loop so not having the heater on probably didn't help their life.

PS For what it is worth I sprayed starting fluid around the injectors/Y pipe/etc. the best I could and didn't notice any change in the idle.

PSS There is just one rubber seal that goes between the injector and the actual manifold itself, right?

Chris@Rvengeperformance
05-28-2013, 10:07 PM
You have the upper spacer on the injector, right?

Sent from my RM-845_nam_vzw_100 using Board Express

HLxDrummer
05-28-2013, 10:17 PM
You have the upper spacer on the injector, right?

Sent from my RM-845_nam_vzw_100 using Board Express

These: STM: OEM MITSUBISHI FUEL INJECTOR SHEET | EVO VIII-IX | 90-99 DSM | MD614805 (http://www.streettunedmotorsports.com/parts/oem_evo_dsm_fuel_injector_sheet_md614805.htm)

If so, ya I put those on.

Chris@Rvengeperformance
05-28-2013, 11:48 PM
yeah that is what I meant.

very strange, I had nothing but great lucky with the 560s and the flash ecu.

HLxDrummer
05-29-2013, 08:57 AM
I know it is really weird.. I swear my car is like a prototype. My Maximal TC brace didn't fit, Maximal control arms didn't fit at first, and a couple other things didn't work out as it should/does on other cars.

I have a bunch of tests coming up so I'm going to try to focus on them instead of working on the car but I guess afterwards I'll put the stockers on and see if the problem goes away. Or just limp it to my dads and pressure test..

If anyone has any ideas still feel free to throw them up.

Thanks again for the help!

Greg E
05-29-2013, 10:47 AM
Buy a compressor and do an intake leak test....

HLxDrummer
07-18-2013, 10:11 AM
Well I finally got a compressor but I have already uninstalled the Evo injectors. I sent them back to Evotuner and he said they tested just fine. I think I am going to let him keep them for a partial refund because I don't want to risk selling them to somebody if they aren't working right (which I believe is the case).

I tried them with the same exact setup/seals as I am running now with stock injectors and they ran like crap while the stockers run great. Dunno what the issue was.