PDA

View Full Version : Pump Gas Limitations



Chris@Rvengeperformance
01-18-2013, 06:48 PM
I know this is a sensitive topic for some, but I'd like to get a discussion going. There are many that say pump gas is a waste of time. Well, I for one like to be able to run times at the track that fully represent my "street" mode that the car sees daily.

If that is not your cup of tea I am not here to argue with you.

The point of this thread is to talk about the reasons why we are stuck at much lower boost levels than other platforms on pump and what can be done about it. What about our engine or cylinder head design is lacking that causes us to have to run so much less boost than say an Evo? Many say that cleaned up combustion chambers like DR or other heads help, but there has really been not much evidence posted to support that.

I know our stock timing map may be too aggressive for high boost, but then we hear from many that running high boost and low timing doesn't work either. I also know that the whole real point is airflow, but it is easy for most of us to get on the same page if we talk about boost.

Basically the threshold for knock on typical 93 octane gas seems to be as low as 15 PSI for some and maybe low 20s for others. Most people do not seem to venture much about 15 lbs, but that really holds us back.

If you don't want to talk about boost then you can think of it in terms of power. Most cars seem to do well to get to 400-450AWHP with bolt on style turbos and pump gas. What can we do to get past this?

Let's pretend these 3 options are off the table at the moment:

1)Methanol/water injection
2)Race Gas
3)E85

What can we do then?

Greg E
01-18-2013, 07:09 PM
My theory has been this is a result of high EGTs from a poor/very restrictive exhaust manifold, very mild cam overlap and shitty innercoolers.

Greg E
01-18-2013, 07:12 PM
About high timing, that's bull... Peak load, the timing dips all the way back to 10-12degrees and even as low as the single digits if you get enough airflow on a stock timing map. You run a piggy back, then suddenly you run into too high of timing.

Chris@Rvengeperformance
01-18-2013, 07:14 PM
My theory has been this is a result of high EGTs from a poor/very restrictive exhaust manifold, very mild cam overlap and shitty innercoolers.

As far as inter-cooling goes you never see any real results posted about that. Even with a FMIC the ceiling seems to be really low.

Even the all out built to the wall cars never seem to run much past low 20s.

Greg E
01-18-2013, 07:15 PM
Many say that cleaned up combustion chambers like DR or other heads help, but there has really been not much evidence posted to support that.

Missed this note:

I have first hand experience with DR heads. Every car running them were able to run MUCH more boost on pump. Both my previous 95 Stealths were able to run as much as 17-19psi on pump with little to no knock. They performed extremely well!

NickS VR4
01-18-2013, 07:16 PM
My theory has been this is a result of high EGTs from a poor/very restrictive exhaust manifold, very mild cam overlap and shitty innercoolers.

Don't have much to add, but I wonder if Gil's manifolds will help with this.

Sent from my Galaxy Nexus using Tapatalk 2

Chris@Rvengeperformance
01-18-2013, 07:16 PM
Missed this note:

I have first hand experience with DR heads. Every car running them were able to run MUCH more boost on pump. Both my previous 95 Stealths were able to run as much as 17-19psi on pump with little to no knock. They performed extremely well!

good to know and have some solid data. Sounds like they are worth 2-3 more PSI.

Greg E
01-18-2013, 07:16 PM
As far as inter-cooling goes you never see any real results posted about that. Even with a FMIC the ceiling seems to be really low.

Even the all out built to the wall cars never seem to run much past low 20s.

That's pretty good actually.

Chris@Rvengeperformance
01-18-2013, 07:17 PM
Don't have much to add, but I wonder if Gil's manifolds will help with this.

Sent from my Galaxy Nexus using Tapatalk 2

I am looking forward to the dyno testing that has been proposed on them. I'd certainly pick one up if it were worth some tangible gains.

Greg E
01-18-2013, 07:17 PM
Don't have much to add, but I wonder if Gil's manifolds will help with this.

Sent from my Galaxy Nexus using Tapatalk 2

Debating dropping the coin for one. He needs to make a rear one too!

Chris@Rvengeperformance
01-18-2013, 07:18 PM
That's pretty good actually.

I guess I can't wrap my head around evos that seem to get away with 30 on 93 and make 600AWHP out of a 2.0 liter on 93.

Greg E
01-18-2013, 07:19 PM
I guess I can't wrap my head around evos that seem to get away with 30 on 93 and make 600AWHP out of a 2.0 liter on 93.

Much more efficient turbo and inner cooler setup.

NickS VR4
01-18-2013, 07:20 PM
I am looking forward to the dyno testing that has been proposed on them. I'd certainly pick one up if it were worth some tangible gains.

If someone near ray wanted to borrow them while they are off my car the next month or two. I have no problem lending them for a dyno comparison. I have front and rear.

Sent from my Galaxy Nexus using Tapatalk 2

Chris@Rvengeperformance
01-18-2013, 07:21 PM
Much more efficient turbo and inner cooler setup.

how is it we cannot replicate this, or at least get close? Our best intercooler setups are pretty beefy, is there some problem with them I do not know about? I know it is hard to not have a bunch of bends and other issues due to packaging restraints, but the cores themselves should be ok on the good setups.

IPD
01-18-2013, 07:24 PM
is it just DR heads? wouldn't any +1 (stage 3) heads be sufficient for this?

also, are we shelving the idea of strokers for this discussion?

Greg E
01-18-2013, 07:26 PM
I know it is hard to not have a bunch of bends and other issues due to packaging restraints

I believe this is part of the issue.

Greg E
01-18-2013, 07:29 PM
is it just DR heads? wouldn't any +1 (stage 3) heads be sufficient for this?

also, are we shelving the idea of strokers for this discussion?

Just DR heads. Matt M spent YEARS buying NEW sets of heads and applying different combustion chamber designs in an attempt at eliminating the hot spots in the cylinders. I can't for the life of me find that thread but it dates back to the early 2000 era of 3si back when Matt shared a lot of technical info. :(

BTW my DR750 car will be running a stroker.

vr4tune
01-18-2013, 07:54 PM
I'd put my money on cam lobe profile (lift, and duration) and valve timing and over lap. Combustion chamber shape and texture will also play a factor.

Chris@Rvengeperformance
01-18-2013, 07:59 PM
is it just DR heads? wouldn't any +1 (stage 3) heads be sufficient for this?

also, are we shelving the idea of strokers for this discussion?

I would prefer to keep things as simple as possible and not dive into various displacement options. Bore and stroke size does have an effect, but I think any improvements we can come up with will benefit both stock and non stock displacements.

Greg E
01-18-2013, 08:04 PM
I'd put my money on cam lobe profile (lift, and duration) and valve timing and over lap.

Completely agree. Everyone is so bent on sticking with the stock cams...

It's really more of a bang for the buck mentality with this group though. 4 cams are expensive to swap out and no one can "prove" results from just a cam swap alone.

NOMIEZVR4
01-18-2013, 08:12 PM
great thread...I was only able to run 14lbs on my setup before knocking on pump 93. Later I found out my car was burning some oil(WTF...only 4k miles on the rebuild!) so it was fouling the plugs out...I'm gonna re-ring the bottom end myself this time around and hopefully this spring i'll be able to contribute some useful data to this thread.

Its crazy you're absolutely right, EVO's with stock turbos and upgraded I/C and cams have no problem running mid-hi 20's boost ...im so jealous.

IPD
01-18-2013, 08:36 PM
Just DR heads. Matt M spent YEARS buying NEW sets of heads and applying different combustion chamber designs in an attempt at eliminating the hot spots in the cylinders. I can't for the life of me find that thread but it dates back to the early 2000 era of 3si back when Matt shared a lot of technical info. :(

BTW my DR750 car will be running a stroker.

i'd like to see some numbers/data to back up that claim on DR heads. i'm not really seeing how you can possibly modify them THAT differently that it will provide substantial benefits that other stage 3 heads do not have.

i almost was going to run 750's on a stroker, but matt himself said it would be a waste, so i'm going with 16g's instead.

JasonY
01-18-2013, 09:44 PM
I went 11.1X at 125mph on DR2 heads with old school DR650's on pump 93 and meth at 22-24psi(fell to 22psi) Could run 18-19psi on straight pump. ARC2 only fuel control. Stock heads came setup, 14-15psi reliably. 16 was doable, but zero knock is better than 5-6 for 1psi. That was just the stock valved stage 2's also.

Other than Abram has anyone even come close with that setup? Only weight reduction on my car was 1pc CFDS, Tien coil overs, 18x9.5 TE37's. DSM sidemounts and DNP hardpipes, 500ccs of meth, plus the normal supporting mods of a 3/S circa 03/4.

Jason

TurboSinceBirth
01-18-2013, 11:57 PM
I skipped pump altogether because our 91 is even worse than 93. On smaller turbos I couldn't get past 14 psi without knock which was one reason for switching fuels. I'd be curious to see what you guys come up with.

R/T93
01-19-2013, 12:07 AM
Debating dropping the coin for one. He needs to make a rear one too!

He does make a rear one.

J. Fast
01-19-2013, 01:25 AM
Anyone opposed to running low 20 to mid teen timing at 20psi on pumpgas? I ran my 19t setup like that for years with zero knock issues. I don't understand why you guys are having knock issues at 15 psi on pumpgas. Sounds like its a combination of heatsoak, really bad airflow, , an climate differences. Dont forget wrong temp range plugs and improper gap are huge knock culprits also.

TurboSinceBirth
01-19-2013, 01:42 AM
Mine at the time was definitely heatsoak. You can thank the previous owner installing a crappy auto parts replacement radiator for that.

mb3000
01-19-2013, 02:44 AM
My .02 goes to the turbochargers themselves. The vast majority of 3/s owners are pushing their turbos past the compressor map, much less keeping their max rpm/P.R. plot inside of the highest efficiency island.

futurevr4man
01-19-2013, 01:46 PM
i know in my experience on my first engine build, i had a 3sx forged bottom end, as far as i know the heads were stock, on some cheeeeaaaapppp 19t's. i ran 18 - 19psi with 0 knock, and i figured that was normal. the compression was also 8.5:1.... maybe i just got lucky? the car ran like a scalded dog, but i never got a pass at the track to prove times. ended up lifting the heads, and then went with my big build.

fwiw, im hoping i can see low - mid 20's on this big build, but its a stroker/DR stage 3 heads with big turbos, so it doesnt really apply to this conversation.

whats interesting to note is even people with strokers and nice heads/intercoolers/turbos are still only seeing 19ish psi on pump. take leonel for instance...


http://www.youtube.com/watch?v=Ane1NhXk-O0

as far as i know, thats all tuned out on 93 pump by ray with no meth.


chris, i share your opinions on running pump, which is exactly what i plan to do on my car. im hoping for mid 600's on pump. and i think the issue is in the cams personally, but i have nothing to prove that...

vr4tune
01-19-2013, 04:15 PM
When I switched cams I also did cam gears and ported the heads with 2mm oversized valves. After the switch I wasn't able to run as much boost. I went from 18psi on the pure stock heads and cams to 15psi on the new heads and cams.

I still made more power because of the increase of flow [less resistance in the heads] per psi of boost. Power wise I now make at 15psi what I used to make at 21psi

Right now I'm thinking I can pull a few more psi if I properly degree my cams. I have 3sx gears so I'm sure they are off as well as the cams may not be perfect either. Plus the heads were milled a smidgen. Those three thing all compiled together could be throwing my cam timing way off.

NOMIEZVR4
01-19-2013, 05:42 PM
also gotta keep in mind...as far as pump gas limits for our rivals that came out in the same era, were all relatively in the same ballpark. BPU supra's normally can't run more than 17-18lbs on pumpgas, RX-7's I barely see running more than 13lbs and 300ZX's are also limited to the mid-teens. The EVO and STi are almost 2 generations newer so its kinda apples to oranges comparison.

Julianvr4
01-19-2013, 08:51 PM
2slow2tedius on 3si...I don't post much here but here is my take on it:

Our rear manifold is a 1n3/4 collected cast manifold, our front is a 1n3/4" half-ass log manifold, feeding a turbine housing as wide as my thumb, using a wheel that was devised in the 80's.
This is why the stock exhaust is ok'ish...we have several restrictions in place, and no matter what you upgrade downstream, it doesn't fix the bunk ass hotside we have (and share with many bolt-on turbos) then if you look at the microscopic internal waste gates we have...another fail. We are supposed to be sending exhaust gas outta that straw hole. Someone needs to cast a bigger hotside.

Adam vr4 running 14b's and adapter plates was able to squeeze out more boost after he got an actual manifold setup.

DSM's and EVO's get a set of hks 272's almost immediately because the are so inexpensive to get their stock cams reground ($200) for us, it's about $400 from Delta camshaft who will copy the lift/duration of the HKS 272's. They also have a much newer front mount, and a BIGGER TURBO. EVOs run 20-21 psi stock on the 16g. They don't have 3 cat converters or limited to a 3" down pipe for 3L of displacement. Packaging constraints are less of an issue for them.



Half-ass proof
My last setup on 9b's and stock cams, I would hit fuel cut before I got any knock at 18-19psi. The car was FAST after I put a fuel pump and a clutch in it. The car weighed 3500lbs with a 1/4 tank of gas. This was on a JDM ecu and I had gone through the combustion chambers with 220g and 320g sand paper to knock down the high spots and smooth out the texture. Nothing to it. Note that I was also running open downpipe the entire time. On 9b's. Stock side mounts. Very healthy engine, perfect compression, NEW OEM IGNITION (coil pack/ptu/plug wires).


This next build that I'm very close to finishing (twin HX35's on a BONE STOCK 6G74) will probably poop out at 15-16psi without meth injection just because of the high compression (making 550whp on 93oct) I've done everything I can to make sure that my biggest restriction is the cylinder heads lol.

Sent from my DROID BIONIC using Tapatalk 2



Sent from my DROID BIONIC using Tapatalk 2

J. Fast
01-19-2013, 11:19 PM
Lets compare real airflow and timing numbers and see where the discrepency lies. I think the low knock thresholds are functions of end user, tuning strategy, and true EFI fundamentals. I looked at my AEM timing maps for a number of pumpgas setups. Not one has timing over 18 degrees with as much as 22 psi on pumpgas on TD04's.

I think tuning is still very much a black art and premonitions made based on information provided by highly regarded and influential people has been reared and repeated like gospel. When I went to EFIU I discovered much of the information being passed around this community is ultra conservative and no where near optimal.

It will show itself with real data. Lets see some timing maps and the results with them.

keo92stealth
01-20-2013, 12:40 AM
Completely agree. Everyone is so bent on sticking with the stock cams...

It's really more of a bang for the buck mentality with this group though. 4 cams are expensive to swap out and no one can "prove" results from just a cam swap alone.
I also agree. Every other platforms cams are 300 to 400 bucks where ours are 700 to 800.

By the way this is a great topic.

Julianvr4
01-20-2013, 10:19 AM
Deltacam will copy an hks272, 264, or 280 cam for $93 per cam. They send you the shims, no re-degreeing necessary as if they were new billet cores.

Buying new valve springs to capitalize on the cams is another adventure though. I would also be hung up on paying $500 for a set of springs

Sent from my DROID BIONIC using Tapatalk 2

keo92stealth
01-20-2013, 02:01 PM
But I was always told, cams don't mean shit if they're in stock heads . I would atleast put bigger valves before I went cams.

futurevr4man
01-20-2013, 02:13 PM
But I was always told, cams don't mean shit if they're in stock heads . I would atleast put bigger valves before I went cams . I would just skip the pump gas altogether and just go e85. Chris hills car is the prime example . Shit made 8xx awhp on ethonal type fuel . Probably would have tapped out way before that on pump gas . Cars a beast .

im not just aiming this at you, but in general it really freakin frustrates me when people say things like this. not everyone has e85 available and its ignorant to think they do. i have 1... ONE station within like 60 miles of me. it is NOT pump gas, and more than that, the beginning of this thread said to take e85 and race gas off the table.

this thread has absolutely nothing to do with what fuel you are using. its a discussion of efficiency and power and why we have less of each compared to other platforms. please do not fill this with 'just use e85 cause joe schmo and his brother made more power using it'. of course they did. its the most oxygen rich fuel on the market.

NickS VR4
01-20-2013, 02:42 PM
Just a thought... Is it possible we are limited due to the Cast Iron block not able to disperse heat as well as aluminum? Maybe our cylinders are getting too hot.

masterjr33
01-20-2013, 02:50 PM
im still going with crappy manifolds causing to much exhaust gas restriction.if you cant clear the stock chambers of recently burnt fuel and gas that is 1400* plus. how are you going to effectivly control the next mitxture coming in from pre igniting.

keo92stealth
01-20-2013, 03:01 PM
im not just aiming this at you, but in general it really freakin frustrates me when people say things like this. not everyone has e85 available and its ignorant to think they do. i have 1... ONE station within like 60 miles of me. it is NOT pump gas, and more than that, the beginning of this thread said to take e85 and race gas off the table.

this thread has absolutely nothing to do with what fuel you are using. its a discussion of efficiency and power and why we have less of each compared to other platforms. please do not fill this with 'just use e85 cause joe schmo and his brother made more power using it'. of course they did. its the most oxygen rich fuel on the market.
correct smart ass . I misread the first post . E85 is not in the topic .carry on .

JasonY
01-20-2013, 03:01 PM
I bet a 4L with twin GT35's could run mid/upper 20's boost on 93. Like mentioned, most of these setups are much more efficient on the exhaust side of things than most of our cars. "big" to us is still TD05 or T3 with a small a/r.

Jason

keo92stealth
01-20-2013, 03:09 PM
Since we are comparing the 3s to other platforms I would simply say that the head design plays a huge part . Someone should post some stock flow numbers between different heads .

R/T93
01-20-2013, 03:29 PM
Stan Weiss' - Cylinder Head Flow Data at 28 Inches of Water -- DFW / FLW Flow Files for use with Engine Simulation Software (http://users.erols.com/srweiss/tablehdc.htm)

Check that out, a vr-4 is on there as well as mostly everything else. 242/212 @ .400 and 28 inches. Jrod's head guy claims 304 intake after their work, DR probably similar.

R/T93
01-20-2013, 03:35 PM
im still going with crappy manifolds causing to much exhaust gas restriction.if you cant clear the stock chambers of recently burnt fuel and gas that is 1400* plus. how are you going to effectivly control the next mitxture coming in from pre igniting.

I was up to 930-970C all day yesterday road racing. 1700-1770F. This was at 11 psi with 9b's.

Julianvr4
01-20-2013, 03:53 PM
To my knowledge, the 3S heads really aren't that bad. The 300zx heads flow worse and they have two log style exhaust manifolds. Major factor would be that they have two bigger Turbos. A BPU 300zx makes 400-425 wheel at low 20-something psi. They don't hold that to redline tho. Restrictive hotside lol

Sent from my DROID BIONIC using Tapatalk 2

TurboSinceBirth
01-20-2013, 04:49 PM
Has anyone done a dyno on Mivec heads with pump gas? I know Itallo and the guy with the Eclipse Mivec 3.8L motor have both made 800-1000AWHP plus on race gas or ethanol, but I couldn't remember what they were able to run on pump. Unported those Mivec heads flow better than our Stage III heads iirc. I know ported with bigger valves the Mivec flows better for sure. Both of those owners have bigger manifolds, exhausts, intakes, intercooler pipes, etc to make a more efficient setup. If they can't run more than 20-23 psi, then there's something else holding us back or it just isn't possible due to the inefficient design of an older V6 compared to a new 4-cylinder.

futurevr4man
01-20-2013, 08:08 PM
Has anyone done a dyno on Mivec heads with pump gas? I know Itallo and the guy with the Eclipse Mivec 3.8L motor have both made 800-1000AWHP plus on race gas or ethanol, but I couldn't remember what they were able to run on pump. Unported those Mivec heads flow better than our Stage III heads iirc. I know ported with bigger valves the Mivec flows better for sure. Both of those owners have bigger manifolds, exhausts, intakes, intercooler pipes, etc to make a more efficient setup. If they can't run more than 20-23 psi, then there's something else holding us back or it just isn't possible due to the inefficient design of an older V6 compared to a new 4-cylinder.


thats what i was saying earlier when i posted the vid (leonels car). him and italo have the same setup except italo has slightly different turbos and mivec. bottom ends and manifolds are the same iirc. thats kinda why i lean on cams being the culprit because many people have changed every other variable but as anyonebutme always says, there are no truly *good* cams made for our cars yet. you are almost certain to not gain max potential power with just a cam swap unless you put adjustable cam gears on there too. i wish someone on here had the pull to investigate into getting cams made and swapping them in for direct comparison

NOMIEZVR4
01-20-2013, 11:08 PM
After so much effort and work that has been put into developing the Flash ECU for our platform, making and testing a set of cams should definitely be doable. EVO's regularly pick up 40whp with a cam swap with supporting mods. We've also got quite a few technical savy 3/s gurus still with the platform...its just a matter of time IMO.

DG
01-21-2013, 12:53 AM
Back in 2002 Carroll Smith showed up at a race I was at. I ran into him and convinced him to come look at my car (the Talon) because in the space of 24 hours it had gone from a championship winner to undrivable at the same track, same weather, same tires and I was at my wit's end figuring out why.

Carroll looks at the car and starts asking me questions. I have NO answers. Lots of "I think this" and "the general consensus on the Internet is this" but nothing specific to my car.

After 20 min of bullshit and blank stares, a visibly frustrated Carroll says "dear God man, you're supposed to be the engineer here. If you don't know these answers, how the hell am I supposed to know?"

It was like being shot in the head with a diamond -and revolutionized my approach to car setup. Suspension got measured and modeled. Sensors got added and logged. Shocks and springs were measured and dynoed. You name it, I did it - and I learned a shitload about suspension tuning, including highlighting all the stuff I (and most other people) got wrong (and discovered too that most shock companies made shit and had no idea).

I very much support this topic; I'm moving to New Brunswick this summer and will lose access to Sunoco 94. I'm going to have to re-tune the car for 91 octane and I'm keen to see what people find.

But if you are gonna do it, do it right. Wanna know the difference between the EVO head and the 3G? Buy an EVO head and break out the calipers. CC the combustion chambers. Make rubber casts of the head passages and compare them. Slice up those casts and compare sectional area and shape. Break out the band saw and cut some heads open, look at wall thicknesses, look at coolant flows. Build a flow bench (or rent time on one) and get real flow numbers you can trust. Measure cam profiles. Detail every way that the heads differ, and every way that they are the same. Grab some stock intercooler pipes, compare length and volume. Etc etc etc.

I have some books from the 80s that do this with Pontiac motors (real Pontiacs, not the Chevy stuff) that details the similarities and differences between every single engine Pontiac ever made - head castings, camshafts, cranks - the works. Flow numbers, valve sizes, port shapes, chamber CC for every single head casting. All cam specs for every single OEM cam part number. And this predates digital publishing - these books were put together the old fashioned way, with scissors, typewriters, and rubber cement before going to camera and Linotype. Those old skool guys had their shit wired; they were working when it was much harder to communicate, they did it in less time, and in some cases, with smaller production numbers from which to source examples (not a whole lot of RamAir IV parts to measure, and they even had details on the prototyped - but never released publicly - Ram Air V)

Why the Import guys never did this sort of stuff is beyond me... but there's no reason why the 3S crowd couldn't start.

If you are really serious about learning this stuff, start measuring parts and publishing your findings, instead of working off rumour and innuendo.

DG

GTOJOE
01-21-2013, 03:04 AM
2slow2tedius on 3si...I don't post much here but here is my take on it:

Our rear manifold is a 1n3/4 collected cast manifold, our front is a 1n3/4" half-ass log manifold, feeding a turbine housing as wide as my thumb, using a wheel that was devised in the 80's.
This is why the stock exhaust is ok'ish...we have several restrictions in place, and no matter what you upgrade downstream, it doesn't fix the bunk ass hotside we have (and share with many bolt-on turbos) then if you look at the microscopic internal waste gates we have...another fail. We are supposed to be sending exhaust gas outta that straw hole. Someone needs to cast a bigger hotside.

Adam vr4 running 14b's and adapter plates was able to squeeze out more boost after he got an actual manifold setup.

DSM's and EVO's get a set of hks 272's almost immediately because the are so inexpensive to get their stock cams reground ($200) for us, it's about $400 from Delta camshaft who will copy the lift/duration of the HKS 272's. They also have a much newer front mount, and a BIGGER TURBO. EVOs run 20-21 psi stock on the 16g. They don't have 3 cat converters or limited to a 3" down pipe for 3L of displacement. Packaging constraints are less of an issue for them.



Half-ass proof
My last setup on 9b's and stock cams, I would hit fuel cut before I got any knock at 18-19psi. The car was FAST after I put a fuel pump and a clutch in it. The car weighed 3500lbs with a 1/4 tank of gas. This was on a JDM ecu and I had gone through the combustion chambers with 220g and 320g sand paper to knock down the high spots and smooth out the texture. Nothing to it. Note that I was also running open downpipe the entire time. On 9b's. Stock side mounts. Very healthy engine, perfect compression, NEW OEM IGNITION (coil pack/ptu/plug wires).


This next build that I'm very close to finishing (twin HX35's on a BONE STOCK 6G74) will probably poop out at 15-16psi without meth injection just because of the high compression (making 550whp on 93oct) I've done everything I can to make sure that my biggest restriction is the cylinder heads lol.

Sent from my DROID BIONIC using Tapatalk 2



Sent from my DROID BIONIC using Tapatalk 2

A guy here in Melbourne bought a set of dr750s removed the exhaust housing and used a modified set he made by 9383464 a band around the hot side and machining the exhaust port larger. Haven't heard if he has dyno results for it though. Someone needs to do this and do a back to back comparison.

Sent from my GT-I9300 using Tapatalk 2

GTOJOE
01-21-2013, 03:05 AM
2slow2tedius on 3si...I don't post much here but here is my take on it:

Our rear manifold is a 1n3/4 collected cast manifold, our front is a 1n3/4" half-ass log manifold, feeding a turbine housing as wide as my thumb, using a wheel that was devised in the 80's.
This is why the stock exhaust is ok'ish...we have several restrictions in place, and no matter what you upgrade downstream, it doesn't fix the bunk ass hotside we have (and share with many bolt-on turbos) then if you look at the microscopic internal waste gates we have...another fail. We are supposed to be sending exhaust gas outta that straw hole. Someone needs to cast a bigger hotside.

Adam vr4 running 14b's and adapter plates was able to squeeze out more boost after he got an actual manifold setup.

DSM's and EVO's get a set of hks 272's almost immediately because the are so inexpensive to get their stock cams reground ($200) for us, it's about $400 from Delta camshaft who will copy the lift/duration of the HKS 272's. They also have a much newer front mount, and a BIGGER TURBO. EVOs run 20-21 psi stock on the 16g. They don't have 3 cat converters or limited to a 3" down pipe for 3L of displacement. Packaging constraints are less of an issue for them.



Half-ass proof
My last setup on 9b's and stock cams, I would hit fuel cut before I got any knock at 18-19psi. The car was FAST after I put a fuel pump and a clutch in it. The car weighed 3500lbs with a 1/4 tank of gas. This was on a JDM ecu and I had gone through the combustion chambers with 220g and 320g sand paper to knock down the high spots and smooth out the texture. Nothing to it. Note that I was also running open downpipe the entire time. On 9b's. Stock side mounts. Very healthy engine, perfect compression, NEW OEM IGNITION (coil pack/ptu/plug wires).


This next build that I'm very close to finishing (twin HX35's on a BONE STOCK 6G74) will probably poop out at 15-16psi without meth injection just because of the high compression (making 550whp on 93oct) I've done everything I can to make sure that my biggest restriction is the cylinder heads lol.

Sent from my DROID BIONIC using Tapatalk 2



Sent from my DROID BIONIC using Tapatalk 2

A guy here in Melbourne bought a set of dr750s removed the exhaust housing and used a modified set he made by welding a band around the hot side and machining the exhaust port larger. Haven't heard if he has dyno results for it though. Someone needs to do this and do a back to back comparison.

Sent from my GT-I9300 using Tapatalk 2