Page 2 of 8 FirstFirst 1234 ... LastLast
Results 11 to 20 of 77

Thread: AWD conversion/engine build

  1. #11
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    How to keep a motor mount from walking


    When I got this mount the center metal sleeve was a little loose and the poly insert could be pushed around some when it was cold. This is how I fixed that.




    Find some thick pipe that closely fits the OD of the motor mount metal sleeve. Mark and cut so it will be flush with the sleeve. I cut them a little thick then ground them down to fit.




    ^ 3SX Pen plug! send me free stuff guys! ^






    Wrap the sleeve in some electrical tape to take up any room between the OD of the sleeve and the ID of the pipe so they fit snug and don’t rattle.







    Then just drill some holes and put in some good screws.





    That should work

  2. #12
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    Parts ready to be welded








    Rear subframe ready to be mounted








    Intercooler mounted







    Next things to do is change and hotwire fuel pump, assemble the engine and transmission.

  3. #13
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts





    :lol3: all I have at the moment.

  4. #14
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    I'm using the stock shroud for an intercooler shroud. It looks like it will work out pretty good.








    I think I need to cut a little out on the inside of the bumper. Nothing that would show from the front.










  5. #15
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts





  6. #16
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts




  7. #17
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    Well the AWD part is done. Just need to finish the engine and trans.



  8. #18
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    ACTION SHOT!


  9. #19
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    Sorry I haven’t updated this thread lately but pretty much all my spare time has been working on the car.

    From lack of proper tools I was dreading pulling the races in and out to shim the trans. The only thing I needed to check was the diff because I'm installing a modified OBX LSD. I like to make things as easy as posible. I decided to use new bearings on it so I took the old race and ground down the sides so I could pull it in and out very easy without tearing up the seal or heat the casing ect. I know there could be a slight difference in the old race and new but apparently not enough to worry about because it came out almost perfect. Congrats to OBX for building it to the right size.




    Like I said anything to make it easier.

    Yes, casing in the oven and races in the freezer.










    Special thanks to intropy (Justin Pratt), He was a HUGE help! Not sure I could have put it back together (correctly) without him. Thanks man!



    More pics soon to come

  10. #20
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering