How would I go about leak testing on my blow thru setup
How would I go about leak testing on my blow thru setup
i would like to know this also
1/4 mile 11.80 @117mph. 551whp 641trq @ 26psi E85 tune, MTC 19T-HLs, forge 15psi spring wastegates, 780 PTE inj, 3SX Fuel loop, ss fuel lines, Engine built by Laniers Speed shop, block bored .060 w/ chromolly rings, weisco pistons, 3sx custom forged rods, forged crank, HKS DLI, AEM EMS, AEM UEGO wideband, prosport oil and boost guages, aeromotive 1000 FPR, Dejon blow thru twintakes, Walbro E85 400 w/ 3sx hotwire kit and custom an fitting fuel pump w/ STM filter to pump line, CXRacing FMIC, Megan Racing Aluminum radiator, IPS custom downpipe, Borla 3" exhaust,Greddy profec b spec II EBC, Blitz SS BOV,R1 Drilled slotted rotors, Drag DR-31 rims, RPS stage 4 unsprung clutch,
I guess we could always put the stock bubble and pipes on and do that but what a PITA
i dont have my bubble anymore, but sure I could get one. I think im gonna fabricate a pressure tester for blow thru set ups.
block off one turbo with a rubber pipe cap. Then build a circular pressure tester for the other side like this:
Intake Leak Pressure Tester
Parting 6 speed
Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace
Tried to find it on this site, but only found it on the other site.
3000GT/Stealth International Message Center
92 Red VR4 - BPU: Sold
93 SS VR4 - BPU: Sold
94 VR$ - Not Stock
Light travels faster then sound. This is why some people appear bright until you hear them speak.
"Transire suum pectus mundoque potiri"
(Rise above oneself and grasp the world).
"Give me a fixed point, and I will move the Earth."
(Archimedes)
I have come here to chew bubblegum and kick ass... and I'm all out of bubblegum.
(Roddy Piper)
go to the hardware store and buy a valve stem and a pvc cap
drill a hole in the cap and push the valve stem through it. then just remove the ic pipe going to the maf and put in the pvc cap. pressurize and bam your done.
the basic go fast bits...
forged short block, Billet DR1000's, 680cc injectors, meth inj, FMIC, MAFT, Apexi Neo, hotwired 255lph fuel pump.
Tuned by Ray Pampena
Just a fun Daily Driver.
Be VERY careful that those caps don't blow off the turbo and fly around - I did a similar tester for my evo and somewhere around 25psi the cap popped off. Scared the peanuts out of me. The black couplers should be right near the PVC caps.
1995 VR4 Coupe
I have a Rob Beck pressure tester that fits in the stock air bubble. I ended up getting a 3.5" to 3" reducer and a 3" cap so I can pressure test my blow-through setup. I couldn't even build any pressure because it was leaking out my MAF sensor so I'm going to see how well I can get it to seal up. You can build a pressure tester pretty easily just block one of the turbos off.
95 RT/TT Billet TD04s E70, DW1000cc injectors, ARC-2 with 92mm maf, 3SX fuel rail loop, hotwired Walbro 416/485, 3" FMIC, single small Krank vent, DR 3.5" downpipe and cat-back, DNP 02 housings, Hallman Pro MBC, BlackStealth LCDBC, AEM wideband, AEM oil pressure, Apexi S1 coilovers with SCE EVO 8/9 adapters, 3SX adjustable control arms, Spec 3+ clutch, Maximal solids/3SX poly motor mounts, Setrab custom SMOC, stock motor 127k miles, stock drivetrain.
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Bookmarks