Page 6 of 6 FirstFirst ... 456
Results 51 to 53 of 53

Thread: Ignition testing

  1. #51
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    I scope secondary voltage all the time with my lab scope... A 1k resistor in the signal wire puts you right in range. You can't calculate actual KV without a current reading as well, but I use an inductive clamp for that. In most cases I not that concerned with the actual numbers though, I'm mostly looking at waveform behavior.

    I'll have to get a capture of the DLI in action... I've been curious about how it actually worked. Haven't had a lot of time to play with the scope lately.


    Real Performance Automotive (541)816-4500 www.FB.com/RealPerformanceAuto

  2. #52
    Forum User
    Join Date
    Feb 2014
    Owner Since
    never

    Posts
    58
    Thanks
    1
    Thanked 11 Times in 9 Posts
    Quote Originally Posted by tom93vr4 View Post
    I wonder about increased stress on the PTU & coils if running 18 - 20V and higher current all the time. A DD probably doesn't need that a lot of the time. I like the idea of switching it on via ecu or some other control only when needed.
    Quote Originally Posted by Jesters Deadd View Post
    I was worried about running that voltage all the time. Hence the bsa.
    Btw i recommended increaseing the limit to 90% and the dwell time by 25%
    You guys are obviously more familiar with what is adjustable within the Chrome ECU, but it has a lookup table of battery voltage that is a large factor in the dwell calculation, correct?

    Assuming that is correct, then if you are feeding a different voltage to the coils that the ECU doesn't see, that could result in some unstable dwell current. Say the battery voltage your ECU is reading rises a few volts, it will shorten the dwell. But your regulated voltage to the coils isn't changing, so the shorter dwell time at the same coil supply voltage would lower the actual dwell current. If you are going to make a higher voltage regulated power supply, you'd almost want to either zero out that table. Or make that higher voltage supply relate to the battery voltage that the ECU sees, so that you could then adjust the table to match.
    Last edited by bradrs; 11-16-2015 at 01:19 PM.

  3. #53
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    Yes, there is a table called Coil Dwell Time Vs voltage.



    FYI, that is 15% more dwell than stock.

    Parting 6 speed
    Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace

  4. The Following User Says Thank You to Chris@Rvengeperformance For This Useful Post:


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering