JDM 74 goodies for sale

[Unknownvr4]

Just got my JDM 6g74 in today, I pulled it apart and separated the parts I don't need. These parts have an estimated 50k miles on it stated by the JDM engine supplier.

Forged 6g74 crank - put this in your 72 block for a 3.5L stroker - $500 shipped
Complete 6g74 heads - same as 2G NA heads - good cores, good for a port job, or good replacements for your bad heads after you replace the seals - $300 shipped
Upper 74 timing covers - front one has a cracking pictured, but will still work fine - $50 shipped
Upper 74 intake plenum - $75 shipped
Engine hoist/intake plenum brackets - $30 shipped
74 exhaust manifolds with heat shields - will bolt up to 72 heads, but not sure if they will meet your down pipe - $50 shipped
74 injector harness cover with correct screws - will fit 72 with some trimming - SOLD
Valve covers - look to be the same as a 72, but unsure - $50 shipped
74 injectors - you should probably get themy cleaned - $60 shipped

Also check out my other FS post Two 4 bolt main 72 tuto blocks for use with the 74 crank.

Pictures in next post.

[Unknownvr4]

[Unknownvr4]

[Uniuno]

Where did you get the engine from?

I'll take the injector cover, Please PM me your paypal.

Thanks

[futurevr4man]

I have a question for you:

Where the two timing belt covers meet, is there a plate or something that sits "inside" of them... to keep things from falling behind/under them into the timing belt area? Like above the water tube, but in the V of the heads, on the end... the timing belt covers meet right at the top/middle of the plate.

The plate for a 72 won't fit, and I've always been curious what the 74 one looks like, if there is one. I plan to fab something up when I pull my engine this go-round (or buy yours if you'd sell it to me?!).

Edit: I added your pic with a circle around what I believe to be what I'm after.

20150921_190548_zps4xcqf9zc.jpg

[Unknownvr4]

Where did you get the engine from?

I'll take the injector cover, Please PM me your paypal.

Thanks

Found it on ebay, there were two for sale. Messaged the first seller and then gave this second one a call. The guy was very helpful and was able to answer some questions i had about the engine - even going out to look at the oil filter location. He ended up giving me a discount since I bought over the phone. Jdm engine pro is their name.

Pm coming your way.

[Unknownvr4]

I have a question for you:

Where the two timing belt covers meet, is there a plate or something that sits "inside" of them... to keep things from falling behind/under them into the timing belt area? Like above the water tube, but in the V of the heads, on the end... the timing belt covers meet right at the top/middle of the plate.

The plate for a 72 won't fit, and I've always been curious what the 74 one looks like, if there is one. I plan to fab something up when I pull my engine this go-round (or buy yours if you'd sell it to me?!).

Edit: I added your pic with a circle around what I believe to be what I'm after.

20150921_190548_zps4xcqf9zc.jpg

Haha, I need mine so I am not going to sell it. I'll send you a picture later.

[futurevr4man]

Haha, I need mine so I am not going to sell it. I'll send you a picture later.

Thanks! Was my circle correct?

[Uniuno]

Found it on ebay, there were two for sale. Messaged the first seller and then gave this second one a call. The guy was very helpful and was able to answer some questions i had about the engine - even going out to look at the oil filter location. He ended up giving me a discount since I bought over the phone. Jdm engine pro is their name.

Pm coming your way.

Very cool. I bought mine from BestofJDM.com, that website now redirects somewhere else and the 6g74 isn't listed anymore. They seem to be kinda tricky to find. I also had to wait for it to ship from over seas.

PM received and payment sent. Thank you, sir.

[Unknownvr4]

Thanks! Was my circle correct?

Yes, that's where all the shields on the heads were lol