Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: Power Steering Question

  1. #1
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post

    Power Steering Question

    I have a question about the rack and pump seals and running the system dry. I bought this car last year and it had one of the rear power steering lines severed so it didn't hold fluid for long at all. The previous owner said it wasn't driven much after that issue occurred.

    Now I am about to install everything in the car after a color change and suspension overhaul and I am wondering if I should rebuild both the power steering pump AND the rack.

    My original plan was to blast/paint and rebuild every system on the car, but of course things got drawn out and I really want to just have the car for winter. (Weird I know, but after having to drive the car I've been driving for a year I REALLY want to drive this car). I have the rebuild kits for both the rack and pump purchased, I used Toni's guide on wiki for the part numbers.

    Should I rebuild both now while I have everything out and have easy access OR
    throw it back together and hope for no leaks and everyhing is fine. Thanks for any advice!

  2. #2
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    The pump rebuild is tedious but not that difficult. The rack seals are probably dried out so I would do that one too. I would say leaks are likely and it would be much harder to pull them out once the car is together.

    Mod list (scroll down the page)
    JNS Engineering has your Spyders covered (and uncovered too!!)

  3. #3
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post
    Thank you for the tip kind sir. Looks like I know what I am doing this weekend!

  4. #4
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post
    I finished up rebuilding the rack, that wasn't so bad. Now on to the pump, how do I go about removing the c clip that holds the pulley and shaft on? This looks to be the hardest part of the pump.

  5. #5
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    Hope you were careful on the rack. I've heard it isn't too hard to damage the seals when you slide the rack teeth in.

    If I remember, the C clip wants to spin around the shaft as you pry on it. Is that the issue or is it something else? A picture might jog my memory on what I did.

  6. #6
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post
    Well I actually installed the rack back into the housing and then pulled it out along with the backup washer and seal just to check the seal, but yes I was extra careful when installing the rack since those teeth are quite sharp. It's impossible to access the c-clip because the pulley is in the way. Let me get a couple pics up in a few mins.

  7. #7
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    You have to take it apart from the other side. See this guide.

    Power Steering Pump Rebuild - 3SI Wiki

  8. #8
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post
    I have been following that guide, everything on the other side of the pulley is off. It won't let me upload pics, I don't know how to get them on here.

  9. #9
    JNS Engineering verified
    Join Date
    Sep 2010
    Owner Since
    1994

    Location
    San Jose, CA
    Posts
    2,112
    Thanks
    61
    Thanked 155 Times in 110 Posts
    You have to host pics on an external site (photobucket etc) and then paste links on here using the [img] [/img] tags.

  10. #10
    Forum User
    Join Date
    Dec 2011
    Owner Since
    2009

    Location
    Iowa
    Posts
    99
    Thanks
    0
    Thanked 1 Time in 1 Post

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering