Page 5 of 7 FirstFirst ... 34567 LastLast
Results 41 to 50 of 65

Thread: Trying to figure out why my reman 6-speed is failing...

  1. #41
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts
    so...whats wrong with this picture...oem fork and ball

    EDIT: Its a video

    Last edited by NOMIEZVR4; 09-02-2014 at 11:38 AM.
    95 TD05 16G VR-4---540whp@24psi
    34XXlbs..

  2. #42
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts

  3. #43
    I don't bite
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Southern IN
    Posts
    1,996
    Thanks
    59
    Thanked 98 Times in 80 Posts
    Is that with trans bolted to engine?
    1992 Kilder Green VR4 - First 4G swap in a 3S. 2.0, auto, awd. 9.65 at 143mph. Now LS swapped. 8.52 at 162.

  4. #44
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts
    Yes, that is with motor and trans bolted together.

    More pictures...just disassembled the whole thing..














    Last edited by NOMIEZVR4; 09-02-2014 at 11:40 AM.

  5. #45
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts


    WIth no disc in the middle...




    Its a stock trans, IPS FLywheel, SB stage 4 clutch...OEM TOB, OEM Fork and Ball...any ideas?

  6. #46
    Member Not Verified
    Join Date
    Feb 2011
    Owner Since
    2009

    Location
    Scottsbluff, NE
    Posts
    872
    Thanks
    37
    Thanked 49 Times in 36 Posts
    I don't see what's wrong with it?
    1995 Dodge Stealth R/T Turbo
    Mods: DR750s, BC Sportsman rods, Ross pistons, ACT HD 6 puck clutch, 5 speed transmission, 300M output shaft, Broomfield racing billet transfer case housings, Spectre air filter, GM 3.75" MAF w/translator, DN Pre-turbo pipes, Pampena/CX Racing dual core FMIC, M2 Performance turbo-back exhaust, Walbro 450lph E85 pump, SXPerformance fuel filter, stainless fuel feed lines, EK2 Mfg fuel rails, SXPerformance AFPR, 1000cc Bosch injectors, 99 VR4 replica ECU w/ Chrome for tuning, Kenne Bell Boost-a-Spark, Blitz SBC i-D boost controller, IPS oil cooler, Intrax springs on KYB GR2 struts, Enkei Kojin 18X9.5 +30, Nexen N3000s, 99 front end, carbon fiber steering wheel, Pioneer AVH-X2600BT, JL C2 6.5" and 6"x9" speakers, free 4 channel amp for subs (LOL), twin Alpine 10" type E subs.

    Made 608whp/631wtrq on Pampena's dyno @ 31 psi.

  7. #47
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts
    The fork is still too far over to the right...

    or am I being paranoid?

  8. #48
    Low & Slow verified
    Join Date
    Sep 2010
    Owner Since
    2005

    Location
    Fortson, GA
    Posts
    577
    Thanks
    25
    Thanked 39 Times in 29 Posts
    Looks good to me. That position will probably give maximum throw of the slave cylinder. It has plenty of room for the fork to continue to move toward the engine as the clutch disc wears. The disc seems to have quite a bit of material left. I don't see anything wrong. The play in the video will be gone once the slave is installed. Paranoid, just paranoid.

    Jeff

  9. #49
    There will be Blood! verified
    Join Date
    Sep 2010
    Owner Since
    1997

    Location
    In Sane!
    Posts
    4,677
    Thanks
    1,081
    Thanked 449 Times in 331 Posts
    Have you checked that the step height is within specs?

    Help them, for they know not that which they do not know!
    CoopKill's Mistress Makeover Thread!
    "Punk, Nutswinging, Small Time, Asshat, Monkey, Jerkoff, Loser that rides on other peoples accomplishments!" . .

  10. #50
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    August 2010

    Location
    Chicago
    Posts
    1,494
    Thanks
    46
    Thanked 57 Times in 46 Posts
    Quote Originally Posted by CoopKill View Post
    Have you checked that the step height is within specs?
    the flywheel is a new unit from ips but I guess checking the step height can't hurt.

    Jeff I'll keep you posted.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering