Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: What to replace when installing injectors?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts

    What to replace when installing injectors?

    I am going to try to get around to install my injectors next week and I am wondering what all I should replace while I am doing it. The injectors come with new O-rings and my plenum gasket is a few years old.

    Should I replace the plenum gasket? Should I replace the insulators?

    Trying to save money where I can but I don't want to have to make 18 different orders/pay for shipping a million times either. I am just going to try to place an order through 3SX for everything I need (depending on their shipping charges).

  2. #2
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    The insulators are best to replace because they are a boost leak if they get dried out.

    I've got to the point where it is easier just to replace the plenum gasket each time. felpro's are like $8 from the parts stores. You certainly don't HAVE to, but I just don't have the plenum off as much as I used to.

    Parting 6 speed
    Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace

  3. #3
    RTBOOST verified
    Join Date
    Sep 2010
    Owner Since

    Location
    Florence, Wisconsin
    Posts
    715
    Thanks
    24
    Thanked 29 Times in 19 Posts
    If I were you, I'd personally get all new injector insulators (MD087060) & the fuel injector sheets (MD614805). You said that the injectors already came with o-rings (#1465A188), so that should be all that you would need...If you order through Cherry Hill, prices are $4.71/ea for the sheets & $1.74/ea for the insulators (o-rings are $3.39/ea). If you use 3SE as the code at checkout, that should pretty much cover half or all of the S&H charges.


    Sent from the garage
    '90 Toyota Celica GT Liftback..........................(X) (daily driver)
    '73 Dodge Challenger 340...............................(X)
    '91 Firestorm Red Stealth R/T TT.....................(X)

  4. #4
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    I'll probably just order one from Cherry Hill since I'm placing an order anyhow. I think I've only had the plenum off once or twice so probably worth it.

    As far as the insulators, I need 6 of each right? Thanks a lot, the part numbers are really helpful!

  5. #5
    RTBOOST verified
    Join Date
    Sep 2010
    Owner Since

    Location
    Florence, Wisconsin
    Posts
    715
    Thanks
    24
    Thanked 29 Times in 19 Posts
    Yes, you'll need 6 of each...I was able to just check out my past orders to get you those part #'s as I am eventually swapping my injectors out, too.

    Also, those prices are from a while ago, but I can't see them being too far off, if they've even changed at all.

  6. #6
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    It ended up being $60 shipped (I forgot to put in the coupon code ) for 6 of each of the insulators and a plenum gasket.

  7. #7
    Forum User Not Verified

    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Cape Girardeau
    Posts
    4,791
    Thanks
    365
    Thanked 296 Times in 214 Posts
    holy shit

  8. #8
    Forum User verified
    Join Date
    Sep 2010
    Owner Since
    ~2006

    Location
    Pittsburgh, PA/Wheeling, WV
    Posts
    867
    Thanks
    36
    Thanked 15 Times in 11 Posts
    Quote Originally Posted by Forest Gump View Post
    holy shit
    That is what I say everytime I buy something for this car

  9. #9
    Padawan garage troll Not Verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Newark, DE
    Posts
    635
    Blog Entries
    5
    Thanks
    68
    Thanked 23 Times in 21 Posts
    May try Rock auto

    Revel in your time
    91 AWD TT
    K&N FIPK, Precats gutted, Test Pipe, Blitz DSBC, Walbro 255, Vacuum reduction, SM3, MMCd, Krank Vents, 3SX Aluminum Crank Pulley, Aluminum 2PC DS, MAFT Pro (AFC mode atm).

    To do list: Need to check electronic timing, install FP hotwire, install PS poly MM, RUACAs, Setrab oil cooler, Dejon Y-pipe, 3.5 GM Mas, FIC 650ccs & 13Ts.

  10. #10
    Forum User
    Join Date
    Jun 2011
    Owner Since
    2010

    Location
    Sweden, Gothenburg
    Posts
    835
    Thanks
    32
    Thanked 49 Times in 38 Posts
    just do a visual inspection. all my 2 decade old gaskets on my car has been perfect.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
  • History
  • Information
  • Groups
  • Events
  • Resources
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net