View Profile
View Forum Posts
View Forum Threads
Show All Albums
Private Message
View Articles
View Blog Entries
5 minutes
Sent from the Man Cave!
*\( ^o^ )/*
5 minutes
Sent from the Man Cave!
*\( ^o^ )/*
Help them, for they know not that which they do not know!
CoopKill's Mistress Makeover Thread!
"Punk, Nutswinging, Small Time, Asshat, Monkey, Jerkoff, Loser that rides on other peoples accomplishments!" ..
Home Sweet Home!
Sent from the Man Cave!
*\( ^o^ )/*
As he mentioned clearances are tighter.
Sent from the Man Cave!
*\( ^o^ )/*
Last edited by CoopKill; 06-03-2014 at 08:10 PM.
Originally Posted by CoopKill
Home Sweet Home!
Sent from the Man Cave!
*\( ^o^ )/*
i see see what you did there.
Ported heads, IPS 2mm oversized valves, Delta 264/272 cams, 3SX High rev valve springs, 3SX cam gears,
Merkel 6g72 3.5L BILLET crank stroker (going in this summer), 3sx poly motor mounts
IPS EvoIII turbo kit, HKS SSQV bov, ETS anodized FMIC, AEM intake filters, Tanabe Turbo Back Concept G Blue Exhaust,
HKS DLI, Ultra spark plug wires, Denso iridium IK24 spark plugs,
JSPEC trans, Ultimate Performance short throw shifter, Spec carbon twin disk clutch, PST aluminum 2 piece drive shaft,
Denso Supra fuel pump, RC 750cc fuel injectors, AEM Fuel pressure regulator,
AEM wideband & boost gauge, AEM EMS in speed density,
Addco sway bars, DBA 4000 drilled & slotted rotors, Enkei PF01 18x9 +45, BFGoodrich g-froce KDW 245/40/R18
Wut?
pretty big ring gaps
Parting 6 speed
Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace
I believe that is the info that came with them. I will be crushed if I have to tear it down, and replace them... Again!
Oh, I think it will run okay, but I would expect seeing closer to .020. It might just use a little more oil, but you definitely won't worry about the rings butting and breaking.
I agree... Run it, it will be fine. I would have run them tighter, and usually run the 2nd ring equal or slightly wider than the top ring, (there are differing theories on that which could spark endless debate) but yours aren't wide enough to be a problem...
Just edging out the monster block form the picture! You didn't want her to steal the spot light.
Posting Permissions
|
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
|
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
|
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
|
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Reply With Quote
Bookmarks