I have also been told it is gear rattle

I have also been told it is gear rattle
Parting 6 speed
Pampena 3.5 Stroker, GTX 2867 Gen IIs, AEM Series2, oohnoo SMIC, DN Hardpipes, FIC 1650s, Walbro 525, aermotive fpr, Dejon intake pipes, Tial Q, Koyo Rad, Samco Hoses, Stoptech 332mm fronts, HKS GT4 Coilovers, Spec 4+ LW, JDM 6 Speed, Billet shift forks, Pampena brace
I could never hear anything over the sound of the exhaust except for the lifters ticking.![]()
95 RT/TT Billet TD04s E70, DW1000cc injectors, ARC-2 with 92mm maf, 3SX fuel rail loop, hotwired Walbro 416/485, 3" FMIC, single small Krank vent, DR 3.5" downpipe and cat-back, DNP 02 housings, Hallman Pro MBC, BlackStealth LCDBC, AEM wideband, AEM oil pressure, Apexi S1 coilovers with SCE EVO 8/9 adapters, 3SX adjustable control arms, Spec 3+ clutch, Maximal solids/3SX poly motor mounts, Setrab custom SMOC, stock motor 127k miles, stock drivetrain.
In neutral? Damn that's a loud exhaust
Yeah it is. I will probably swap the JIC exhaust back on if MTC rebuilds my turbos. Otherwise, I'll go bigger and add another muffler or something. It's a 3.5" DR downpipe, 3.5" DR race cat, and then splits into twin 3" Aeroturbine mufflers. I think it was the only particular 3.5" full exhaust DR ever made. I don't know that Adam ever made more than one in existence. Needless to say it wouldn't be long trip friendly but it sure flows.
My 92 and my 95 both rattle. I replaced the TOB assuming that was the problem and it changed nothing.
1995 Dodge Stealth R/T Turbo
Mods: DR750s, BC Sportsman rods, Ross pistons, ACT HD 6 puck clutch, 5 speed transmission, 300M output shaft, Broomfield racing billet transfer case housings, Spectre air filter, GM 3.75" MAF w/translator, DN Pre-turbo pipes, Pampena/CX Racing dual core FMIC, M2 Performance turbo-back exhaust, Walbro 450lph E85 pump, SXPerformance fuel filter, stainless fuel feed lines, EK2 Mfg fuel rails, SXPerformance AFPR, 1000cc Bosch injectors, 99 VR4 replica ECU w/ Chrome for tuning, Kenne Bell Boost-a-Spark, Blitz SBC i-D boost controller, IPS oil cooler, Intrax springs on KYB GR2 struts, Enkei Kojin 18X9.5 +30, Nexen N3000s, 99 front end, carbon fiber steering wheel, Pioneer AVH-X2600BT, JL C2 6.5" and 6"x9" speakers, free 4 channel amp for subs (LOL), twin Alpine 10" type E subs.
Made 608whp/631wtrq on Pampena's dyno @ 31 psi.
ya, i wasnt sure if it would cause an issue to the clutch itself. Ever since i went to the unsprng disc it has done this.
1/4 mile 11.80 @117mph. 551whp 641trq @ 26psi E85 tune, MTC 19T-HLs, forge 15psi spring wastegates, 780 PTE inj, 3SX Fuel loop, ss fuel lines, Engine built by Laniers Speed shop, block bored .060 w/ chromolly rings, weisco pistons, 3sx custom forged rods, forged crank, HKS DLI, AEM EMS, AEM UEGO wideband, prosport oil and boost guages, aeromotive 1000 FPR, Dejon blow thru twintakes, Walbro E85 400 w/ 3sx hotwire kit and custom an fitting fuel pump w/ STM filter to pump line, CXRacing FMIC, Megan Racing Aluminum radiator, IPS custom downpipe, Borla 3" exhaust,Greddy profec b spec II EBC, Blitz SS BOV,R1 Drilled slotted rotors, Drag DR-31 rims, RPS stage 4 unsprung clutch,
|
3000gt.com 3000GT / Stealth International WWWboard Archive Jim's (RED3KGT) Reststop |
|
Team 3S 3000GT / Stealth / GTO Information daveblack.net |
|
Michigan 3S MInnesota 3S Wisconsin 3S Iowa, Nebraska, Kansas 3S |
North California 3000GT/Stealth United Society of 3S Owners 3000GT/Stealth/GTO Forums 3000GT/Stealth International |
|
3S National Gathering East Coast Gathering Upper Mid-West Gathering Blue Ridge Gathering |
Bookmarks