Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: VR4 Long block

  1. #1
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts

    VR4 Long block

    Potentially looking for a VR4 long block (or motor + tranny and tcase) that is up to date on maintenance and isn't due for major service (60 or 120k) for at least 30k miles. Don't care if it's a 2 bolt or 4 bolt, 1st gen or 2nd gen.

    All I need is something in good running order that will be dependable enough for a daily driver.

    Currently have a 91 RT/TT which seems to have spun a bearing. 2 and 3 in the tranny seem to have no synchros left, not sure how long they've been like that. 2 grinds no matter what, 3 won't grind if you get close with a quick rev match or shift very gently at normal RPMs. Tcase is almost brand new and was replaced last year under recall. Has only 3-400 miles on it.

    I can trade those (for whatever little bit they're worth) plus some cash. Also have a 25 spline 5 speed with tcase that is in good shape if you are wanting to trade the complete drive train.

    I'd like to keep the total cost under 2k as I am an unemployed college student at the moment. Let me know what you have, it'd be nice to have videos of it running and/or with compression testing.

  2. #2
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    I'm not sure how cheap I can go on a 2-bolt longblock that doesn't need an oil pump, water pump, maybe tensioner, etc. I have some low mileage items except for the oil pump as it's the only 2-bolt I own. The motor has some bent valves. I haven't taken it apart yet to check out the damage. I have a good set of 1st gen heads that probably need new VSS. Other than that I could do a quick hone on the cylinders, put in some new rings, and new bearinigs.
    95 RT/TT Billet TD04s E70, DW1000cc injectors, ARC-2 with 92mm maf, 3SX fuel rail loop, hotwired Walbro 416/485, 3" FMIC, single small Krank vent, DR 3.5" downpipe and cat-back, DNP 02 housings, Hallman Pro MBC, BlackStealth LCDBC, AEM wideband, AEM oil pressure, Apexi S1 coilovers with SCE EVO 8/9 adapters, 3SX adjustable control arms, Spec 3+ clutch, Maximal solids/3SX poly motor mounts, Setrab custom SMOC, stock motor 127k miles, stock drivetrain.

  3. #3
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    I understand. And that's my only concern with the 55k shortblock you and I were discussing. Unfortunately my motor has 170k on it, so even if my spun bearings did nothing but wreck the bearings and SOMEHOW didn't damage anything else in the motor, it'd still need all the stuff for a 120k done soon, or getting a shortblock and having to do all that stuff anyway but then slapping heads with 170k on it doesn't seem like a great idea either. Unfortunately, I find myself in that no man's land where rebuilding what I have with factory will cost about as much as a used set up and rebuilding with forged components is just out of my price range (total to spend to get motor fixed/replaced, new clutch and flywheel and 120k stuff is only around 3k plus whatever I can sell my old motor and tranny for or some other misc parts.)

  4. #4
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    Quote Originally Posted by sergechronos View Post
    I understand. And that's my only concern with the 55k shortblock you and I were discussing. Unfortunately my motor has 170k on it, so even if my spun bearings did nothing but wreck the bearings and SOMEHOW didn't damage anything else in the motor, it'd still need all the stuff for a 120k done soon, or getting a shortblock and having to do all that stuff anyway but then slapping heads with 170k on it doesn't seem like a great idea either. Unfortunately, I find myself in that no man's land where rebuilding what I have with factory will cost about as much as a used set up and rebuilding with forged components is just out of my price range (total to spend to get motor fixed/replaced, new clutch and flywheel and 120k stuff is only around 3k plus whatever I can sell my old motor and tranny for or some other misc parts.)
    2-bolt motors aren't in very big demand. It's a JDM motor supposedly but I've found some other surprises so it could possibly have a forged crank if it isn't an original motor. Regardless, I may be able to put together a long block with the oil pump, rear main seal, oil pan, full timing components, valve covers, water pump, thermostat housing, manifolds if need be, etc possibly for under $1k. I would have to see what else I would need besides a gasket set. I should have everything else in good condition.

  5. #5
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    Just let me know what you can do, like I said I have *some* flexibility and we can put some new stuff on there if need be. Not in a huge rush, it'll be a few weeks before I know for sure how boned my current motor (and turbos and oil cooler) really is. Since I'm basically pulling out of my financial aid for the time being though, cheap and reliable is the key. Forged anything in the bottom end is just a bonus honestly. Long term goal is only something like DR650 or 750s, so nothing too wild.

    Anything else you may want to know about the vehicle before you start seeing if you have that stuff to figure out an estimate and what not? Also: if I have to do clutch+flywheel, would be easier to just order and ship to you to do or do it here myself? Also also: Any issue if we go this route with ordering a set of Gen3 lifters and having them sent there for you to do while you're at it?

  6. #6
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    Quote Originally Posted by sergechronos View Post
    Just let me know what you can do, like I said I have *some* flexibility and we can put some new stuff on there if need be. Not in a huge rush, it'll be a few weeks before I know for sure how boned my current motor (and turbos and oil cooler) really is. Since I'm basically pulling out of my financial aid for the time being though, cheap and reliable is the key. Forged anything in the bottom end is just a bonus honestly. Long term goal is only something like DR650 or 750s, so nothing too wild.

    Anything else you may want to know about the vehicle before you start seeing if you have that stuff to figure out an estimate and what not? Also: if I have to do clutch+flywheel, would be easier to just order and ship to you to do or do it here myself? Also also: Any issue if we go this route with ordering a set of Gen3 lifters and having them sent there for you to do while you're at it?
    On a budget you couldn't go wrong with a 2-bolt to get through college at least. You won't want to be making big power anyways because it will become a money pit breaking parts and such plus I didn't have time to work on my cars hardly at all. It'll probably be a few weeks before I have everything taken apart and then see if any pistons were damaged. I've got an extra set of stock ones and would just need to buy some rings plus bearings. I was planning on either selling it as a 2-bolt short block or long block anyways. I will have to check if I have any used 99 lifters. I know I should have a set of new ones I was going to put in my upgraded heads for my other motor. If we work something out you could always send them to me.

    The clutch and flywheel are easy to bolt on. All you do is bolt the flywheel to the crank, align the disk, and bolt the pressure plate down. I'm sure you can do it.

    I have a few used non-spun bearing oil coolers also I have no idea what I'm going to do with. I'm sure the lines need replacing.

    Maybe somebody has a cheap 4-bolt setup. It would be nice to have one for the strength later down the road when you upgrade turbos so you're not doing it twice but could stretch the budget some. Levani has a 97 VR-4 motor out of a car he's parting I want to say for $1k plus shipping. That wouldn't be a bad deal.
    Last edited by TurboSinceBirth; 01-22-2013 at 12:52 AM.

  7. #7
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    Well I mean honestly this semester should be the last I really need the car for every day driving, transferring to a 4 year school this summer and should be on campus housing or close enough to use public transport. So really 20-30k miles before needing to do 60k (or 120k as needed if oil pump is used) should actually be a couple years. Summer internships at Oak Ridge should bring in the capital to do all that when the time comes.

    So possible things that may need replacing due to spun bearing would be obviously the motor, oil cooler and maybe the turbos depending what I find when I start pulling the motor apart. Rebuild on them would worth it or just get another pair used? Or, given I've got everything to go blow thru and 550cc injectors except new preturbo pipes/individual filters, worth it to just step up to something a little larger at that point? Going price for factory seems to be about 300, 13 and 15g are going for between 4-600 looks like.

    I did ask Levani about his, but he said he couldn't ship. If I still had my truck I'd make a weekend trip up to NY to get it, see the folks and bring it back down. Besides, when it comes time to go crazy I plan on just getting a separate 4 bolt block and building it up on the side and then rotate them back and forth when one fails

  8. #8
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    You could step up to 13G or 15G if you got a set for $4-600. Any bigger and the mods can start to snowball if you get carried away. I would stick to a mostly stock fuel setup outside of injectors and a hotwired Walbro 255. I'm running 1000cc injectors, Walbro 416, and 3SX fuel loop on E70 pushing 30 psi. The rest of my fuel system is stock so I know it can handle quite a bit of fuel 650+AWHP.

    You should see if anyone can make a trip up to NY for you or keep an eye out on the forums in case another complete motor pops up.

  9. #9
    Member verified
    Join Date
    Sep 2012
    Owner Since
    2010

    Location
    Decatur, TN
    Posts
    1,671
    Blog Entries
    7
    Thanks
    57
    Thanked 71 Times in 60 Posts
    I have been keeping my eye out for the last month or so since the motor first spun the bearings, most are short blocks that are either 4 bolt or built and therefore out of my price range. The long blocks I find generally folks don't want to ship them.

    Just see what you might can do and let me know what the cost will be for whatever may be missing or needs to be new. If I can get a long block and new oil cooler and turbos together for like 1500-1600 shipped (tall order I know) then do clutch and flywheel (I think you can get just a stage 2 Comp clutch and flywheel for like 600ish) and keep the total cost under 2500 I'd be pretty happy with that since I could sell the 2g rear end or Intropys keyless entry or maybe the old block and tranny and make back some of that.

  10. #10
    One fix at a time verified
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    Kansas
    Posts
    2,158
    Blog Entries
    1
    Thanks
    60
    Thanked 57 Times in 49 Posts
    Quote Originally Posted by sergechronos View Post
    I have been keeping my eye out for the last month or so since the motor first spun the bearings, most are short blocks that are either 4 bolt or built and therefore out of my price range. The long blocks I find generally folks don't want to ship them.

    Just see what you might can do and let me know what the cost will be for whatever may be missing or needs to be new. If I can get a long block and new oil cooler and turbos together for like 1500-1600 shipped (tall order I know) then do clutch and flywheel (I think you can get just a stage 2 Comp clutch and flywheel for like 600ish) and keep the total cost under 2500 I'd be pretty happy with that since I could sell the 2g rear end or Intropys keyless entry or maybe the old block and tranny and make back some of that.
    If I had an extra SB DXD pressure plate that wasn't worn bad you could get a new OEM disc for it. Basically all the RPS Street clutch is an upgraded pressure plate with an OEM disk. I think the DXD-F clutch I have is too worn to use for anything without losing too much potential clamping force. If I were you I'd get a stock flywheel machined with a new step to spec. A lightweight flywheel will make your rpms drop quicker between shifts. The car revs faster without a load but that's about the only benefit. It should only cost about $35-40 to have the stock flywheel machined. There's another way to save. You might check the classifieds for a used clutch. There's really not a way around spending a chunk for an upgraded one. I probably wouldn't trust a XTD eBay clutch. They're hit or miss.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering