Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 39

Thread: Failing Timing belt tensioners vs upgraded valve springs.

  1. #21
    I don't bite
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Southern IN
    Posts
    1,996
    Thanks
    59
    Thanked 98 Times in 80 Posts
    You are running a gates racing belt? My understanding is they barely stretch. Is it possible you didn't have tension set correctly from the beginning? Or you happened to get a bad tensioner?
    1992 Kilder Green VR4 - First 4G swap in a 3S. 2.0, auto, awd. 9.65 at 143mph. Now LS swapped. 8.52 at 162.

  2. #22
    1st ever COTM and COTY verified
    Join Date
    Aug 2010
    Owner Since
    Birth

    Location
    Tennessee
    Posts
    7,077
    Thanks
    649
    Thanked 451 Times in 347 Posts
    Quote Originally Posted by Streamln1 View Post
    If the belt stretched it would be pushed out farther, not pushed all the way in like mine was. it was definitely 1-2mm from the grenade pin position.

    I may try the shimming idea so it can't bottom out, a lot of these thread responses make sense, so there is more 'at rest' force on the tensioner than a stock setup, so its leaving more slack than necessary between the heads.

    Another weird thing I noticed, theres a lot of blue belt residue on my water pump from the gates belt, its on there thick enough its made the pump pulley feel rough, its as if the pump was 'dragging' on the belt or at times the tension wasn't enough to drive it, which is very bad, I also suspect this may be a tension thing, the pump spins freely enough and it also has just a few thousand miles on it.

    The timing is spot on, and I always checked it periodicly because I am paranoid (having $7k plus in an engine will do that to ya).
    I thought you said it popped out when you turned the engine? All tensioners will compress when the engine sits there. Not every time but if the engine stops in a place where the springs are putting pressure on the tensioner it will compress.

    Quote Originally Posted by HilbillyHomeboy View Post
    I bet she smells of old mustard and sawdust.
    Jeremy

  3. #23
    Forum User Not Verified
    Join Date
    Jan 2012
    Owner Since
    2001

    Location
    Arizona
    Posts
    662
    Thanks
    1
    Thanked 25 Times in 16 Posts
    it never did return to its original stock position, although close.

  4. #24
    Forum User Not Verified
    Join Date
    Jan 2012
    Owner Since
    2001

    Location
    Arizona
    Posts
    662
    Thanks
    1
    Thanked 25 Times in 16 Posts
    Im thinking im going to get a solid tensioner since there really is no definite answer as to any negative effects, since the Kevlar is not going to stretch is not going to be an issue. I could see how a solid on a stock belt could be an issue over time with no way to compensate for stretch. The stock tensioner is the biggest reason there is ever any slack between the heads

  5. #25
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    Just make sure you set it up for optimum tension at operating temp, or set it up slightly loose cold... A Kevlar belt that's too tight will wipe out your cam bearing surfaces pretty easily.

    I've never checked a Kevlar belt, but I've seen with my own eyes a stock tensioner with stock belt moving almost 1/8" from cold operation to full temp operation.


    Real Performance Automotive (541)816-4500 www.FB.com/RealPerformanceAuto

  6. #26
    Forum User Not Verified
    Join Date
    Jan 2012
    Owner Since
    2001

    Location
    Arizona
    Posts
    662
    Thanks
    1
    Thanked 25 Times in 16 Posts
    That worries me. But the stock tensioner does as well, I just do not think its up to the task of handling dual springs, overcompensating by going a little tighter might work but its still not the right way. Either way, something was going on to leave that much belt residue on my water pump pulley, that could only come from the belt not making solid contact occasionally.

  7. #27
    Forum User
    Join Date
    Sep 2010
    Owner Since

    Posts
    503
    Thanks
    11
    Thanked 84 Times in 75 Posts
    If the tensioner was located between the crank, and rear head, increased spring tension could over compress it. The location of the tensioner makes spring tension a non factor.
    Try this, put a wrench on the front exhaust cam to keep it from moving. Take a breaker bar and try to rotate the crank. Watch what happens to the tensioner, it actually extends. The higher the force required to rotate the cams, the lower the tension on the tensioner. The job of the tensioner is to take up slack, not absorb tension.

  8. #28
    Forum User Not Verified
    Join Date
    Jan 2012
    Owner Since
    2001

    Location
    Arizona
    Posts
    662
    Thanks
    1
    Thanked 25 Times in 16 Posts
    of course it does and that proves nothing, Your thinking about it the wrong way. You would be lessoning the tension on it by doing that, but the front head and the heads over all with upgraded springs put more tension on the belt overall than stock, its questionable if the stock tensioner is up to the task, and since prone to fail. At some points the front head is putting a lot of pressure on the belt between it and the crank sprocket. If the tensioner were strong enough, there would never be a point where the spring pressure was enough to create slack between the heads.

    my tensioner compressed inward overall and did not return to stock position fully, there is no force other than constant pressure on the tensioner causing it to weaken that could do this, if the belt stretched it would go the opposite way, not compress inward. As others have stated this is not an uncommon thing with cars with upgraded valve springs and head work. Rays suggestion would work also but I am leaning towards a solid tensioner since that is basically doing the same thing as defeating the stock weak link . If someone came up with an upgraded hydraulic unit that would be great. The floating design if fail proof would be the best of both worlds.
    Last edited by Streamln1; 10-28-2013 at 04:37 AM.

  9. #29
    Forum User
    Join Date
    Sep 2010
    Owner Since

    Posts
    503
    Thanks
    11
    Thanked 84 Times in 75 Posts
    More tension on the belt, doesn't mean more tension on the tensioner.
    Only when the engine is stopped does the front cylinder bank put any tension on the tensioner.
    If the crankshaft is turned backwards, then tension is placed on the tensioner.
    Think about it. The crankshaft turns clockwise, and pulls on the rear head exhaust cam, it also has to turn the rear intake cam, water pump, front intake cam, then front exhaust cam. Now, it's back where it started, and cannot pull on itself. The tensioner is designed to take up the slack in the belt between the front head, and the crankshaft. The overall tension on the belt comes from the resistance the cams have to turning, as long as the tensioner isn't bottomed out.

  10. #30
    Forum User Not Verified
    Join Date
    Jan 2012
    Owner Since
    2001

    Location
    Arizona
    Posts
    662
    Thanks
    1
    Thanked 25 Times in 16 Posts
    also not true, at rest when there is slack between the heads the tensioner is almost fully pushed in, thats the spring tension between the heads and the crank pushing it in. if it stays pushed in like that or is slow to push out for some reason thats how people jump timing.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering