Page 17 of 23 FirstFirst ... 71516171819 ... LastLast
Results 161 to 170 of 226

Thread: 70mm Billet throttle body on sale now!

  1. #161
    I did. I actually had a 70 MM hole saw and carved some out of gasket sheets I bought at Advanced Auto. I traced out the stock gasket on the outside so it's a perfect fit. Almost looked stock but with a 70MM hole.

    But yeah, I am curious to see if yours leaks as well. This is my 2nd one and am not sure if it's just bad luck or the seals can't handle higher boost.

    1993 Dodge Stealth RT/TT - For mod list, visit stealthTT.com.

  2. #162
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since

    Posts
    737
    Thanks
    26
    Thanked 13 Times in 9 Posts
    Thanks for the pictures....THAT's what that is. Never seen one of those before on a magna/diamante TB so that is new to me. Glad to see you've found a solution aswell.
    That little allen key thing at 7 o clock is an idle bypass screw but Im positive there is actually a throttle stop screw aswell....positive...

  3. #163
    Diamonds and Rust
    Join Date
    Sep 2010
    Owner Since
    1-11-01

    Location
    ak
    Posts
    186
    Thanks
    0
    Thanked 6 Times in 5 Posts
    Quote Originally Posted by stealthII View Post
    I did. I actually had a 70 MM hole saw and carved some out of gasket sheets I bought at Advanced Auto. I traced out the stock gasket on the outside so it's a perfect fit. Almost looked stock but with a 70MM hole.

    But yeah, I am curious to see if yours leaks as well. This is my 2nd one and am not sure if it's just bad luck or the seals can't handle higher boost.
    i run about 18lb daily so we'll see. stupid ?, did you use teflon tape when you plugged the 3 vac ports?
    "if i was as slow as you, they'ed bury me" dad

  4. #164
    Another thing to note is that when I got mine, I had to adjust the idle set screw. It's not supposed to be closed all of the way, even at idle according to the service manual. According to the manual, you reverse the screw so that the plate is closed, and then you screw it in 1 1/4 turns.

  5. #165
    I didn't use tape, but I used some thread sealant on them. So I did use a sealant.

  6. #166
    Diamonds and Rust
    Join Date
    Sep 2010
    Owner Since
    1-11-01

    Location
    ak
    Posts
    186
    Thanks
    0
    Thanked 6 Times in 5 Posts
    Quote Originally Posted by TUFFTR View Post
    Thanks for the pictures....THAT's what that is. Never seen one of those before on a magna/diamante TB so that is new to me. Glad to see you've found a solution aswell.
    That little allen key thing at 7 o clock is an idle bypass screw but Im positive there is actually a throttle stop screw aswell....positive...
    we tried to set the tps and found that my sweet spot is 10.9 -96%wot, at 11.3 it 94%wot, any higher we go out of spec. thank you hhh logger. might try again but im sure thats good for now.

  7. #167
    Diamonds and Rust
    Join Date
    Sep 2010
    Owner Since
    1-11-01

    Location
    ak
    Posts
    186
    Thanks
    0
    Thanked 6 Times in 5 Posts
    Quote Originally Posted by stealthII View Post
    Another thing to note is that when I got mine, I had to adjust the idle set screw. It's not supposed to be closed all of the way, even at idle according to the service manual. According to the manual, you reverse the screw so that the plate is closed, and then you screw it in 1 1/4 turns.
    saw that in the manual. i even bought aset of feelr gauges but my friend that helped didnt seemed concerned. im a little out of my leage with elec testing.

    after testing i will see if i need to set that screw and reset the tps.

  8. #168
    Quote Originally Posted by gltasn View Post
    saw that in the manual. i even bought aset of feelr gauges but my friend that helped didnt seemed concerned. im a little out of my leage with elec testing.

    after testing i will see if i need to set that screw and reset the tps.

    Resetting the TPS is easy. You are just testing for continuity on the bottom two pins. You want to adjust it right to the point where you no longer see any continuity between the pins. But like you mentioned, you have to put that feeler gauge right behind the throttle and then do it. It's pretty straight forward.

  9. #169
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since

    Posts
    737
    Thanks
    26
    Thanked 13 Times in 9 Posts
    And yep....Mine leaks aswell from the throttle cable side of things. Plumed in the air line and there was barely any pressure in the intake manifold....actually wasn't even registering on the gauge.......I put my hand where the throttle plate is (closest to firewall) and could could hear the air quieten down as I placed my hand around various things...

    Are we just able to replace the seals? What's the go? Can we use OEM size ones? Maybe needs a different size O ring...
    Anyone figured out a solution?

  10. #170
    Diamonds and Rust
    Join Date
    Sep 2010
    Owner Since
    1-11-01

    Location
    ak
    Posts
    186
    Thanks
    0
    Thanked 6 Times in 5 Posts
    i have a feeling these were not made to be pressurized and they quickly fail. i feel like i got another aftermarket part that was rushed to the market without testing on the platform. mines a leaky pos too. can i get a refund? j

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering